Koon Technology KN518 User manual

1
KN518 VOIP Motherboard
User Manual
1 Description
IP board-casting PCB Board support many connectors, including 4shortcut key, LCD screen, keypad,
handset, double wan port and so on. It can be installed with waterproof telephone, auto-dial
telephone, emergency telephone, elevator intercom, door phone, broadcasting intercom and etc.
The application is very wide.
2 Basic function
Support standard SIP 2.0(RFC3261)and RFC protocol,
Support directly calling to dispatcher station,
Support alarm, monitor, talking and broadcast,
Support common line talk back system,
Adapt high-tech echo cancellation,
Support handset, speaker and alarm adjustment,
Support G.729、G.723、G.711、G.722、G.726 coding and etc,
Support system record and check the recording files freely,
Set through Web(Default IP: 192.168.0.55）
Support upgrade online,
Waterproof and dust-proof design.
3、Technical data
Protocol
SIP 2.0(RFC-3261)
Main chip
DSPG518
Keypad
Design
Stainless steel
Number of direct keys
1、2、3、4（available）
Digital keypad
Available
Voice
Mic
1 pcs
Speaker
2W

2
Volume control
available
Duplex Hnads
Support(AEC)
Handset
Support
Speech stream
Support
RTP
Codec
G.729、G.723、G.711、G.722、G.726
Connector
Feature
Power supply
12V 1A DC or PoE
PoE（not allow IPGB-1）
PoE 802.3af (Class 1) 48V
LAN
10/100BASE-TX s Auto-MDIX, RJ-45
WAN
10/100BASE-TX s Auto-MDIX, RJ-45
Cable specification
UTP or higher then UTP
LCD
Support
RS232
Support
支持(可选)
Working temperature
-40°C-50°C
Relative humidity
10% - 95%
Storage Temperature
0°C to 55°C
IP rating
IP53
3.1 PCB diagram
Keypad
MIC
Speaker

3
3.2 Indicator connection
LED D9 is Registration status indicators,If the connection is correct, the indicator will long light.
3.3 Speed dialing (It needs handset)
soft1(SW3):KEY-COL5 and KEY-ROW1
soft2(SW8): KEY-COL5 and KEY-ROW2
soft3(SW16): KEY-COL5 and EY-ROW3
soft4(SW14): KEY-COL5 and KEY-ROW4

4
3.4 Full Keypad
PIN Definitions
PIN
Definitions
Usage
PIN
PIN
Definitions
Uasge
1
RELAY1
22
SID
Data
2
RELAY2
Alarm
23
SCLK
clock
3
COL0
Keypad IO input
24
AO
4
COL1
Keypad IO input
25
RST
Module reset
5
COL2
Keypad IO input
26
CS
Chip selection

5
5
COL3
Keypad IO input
27
TX+
Handset/MIC +
7
COL4
Keypad IO input
28
TX-
Handset/MIC -
8
COL5
Keypad IO input
29
RX-
Handset/speaker -
9
ROW0
Keypad IO output
30
RX+
Handset/speaker +
10
ROW1
Keypad IO output
31
GND
Earthing device
11
ROW2
Keypad IO output
32
GND
Earthing device
12
ROW3
Keypad IO output
33
MIC+
Handsfree/MIC +
13
ROW4
Keypad IO output
34
MIC-
Handsfree/MIC -
14
RSTN
Keypad IO output
35
GND
Earthing device
15
GND
Earthing device
37
SPK-
Handsfree -
16
HOOK
Hook defection
38
SPK+
Handsfree +
17
VDD
Power supply
39
-
18
LED
Backlight control
40
19
GND
Earthing device
4. Operation
4.1 Setting via Web Browse
Set the computer and telephone in same LAN network;
When this phone and your PC are connected to network, open the Internet Explorer and then enter
the IP address of the WAN port in this phone (e.g. http://xxx.xxx.xxx.xxx). (If the log port is not
standard port 80, you should input http://xxx.xxx.xxx.xxx：xxxx/) See the following web interface.
User: admin
Password: admin

6
※if you didn’t save the setting, the system would the configuration last time when powered on next
time. After changing the parameter, click 【Maintenance】 →
【SAVE】
, the configuration will be saved
and take effect soon.
Before the below steps, please register the phone on your server. The solution【SIP CONFIG】
→INPUT THE SERVER INFORMATION
4.2 WEB Configuration
4.2.1 Status
STATUS
Field Name
Explanation
System
Shows the model number, and current time, status and IP address
Network
Shows the status of connection and other information
Accounts
Shows the status of registration
4.2.2 SIP config
Get your SIP account from your server
Fill the IP address, port,account name, password and number as below.

7
4.2.3 Config
4.2.3.1 Speed dial
Type:Hot key
Value:numner
Line: SIP1/2/3/4
subtype:Speed Dial
You can set four groups in total, fill the information as below.
4.2.3.2 Network
You can set the connection type, auto-negotiation and network port.

8
4.2.3.3 Phone
You can set auto-answer, hookOn wait time, ringer tone, volume settings and codecs settings.
4.2.3.4 Security
Supports 2 output setting
Supports modification on Output Level, Output Trigger Mode (Ring, on hook, talking, DTMF)

9
4.2.3.5 Time
NTP Enable: Yes means synchronizing the time automatically via DHCP mode.
1. Configure primary NTP Server Address and server port
2. Configure secondary NTP Server Address and server port
3. Configure Time Zone
4、Interval time for synchronizing with server. Default is 60 seconds.
4.2.3.6 Language
Change the system language in Chinese or English

10
4.2.4 Maintenance
If the configuration finished, click “the reboot” on the phone to restart the phone.
4.2.5 Logout
Click the Log out button to leave the web operation