Kraus Mateo KPF-2620 User manual

INSTALLATION MANUAL
KPF-2620
Mateo™ Single Lever Pull Down
Kitchen Faucet
www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc. I REV. August 25, 2015

1
Thank you for purchasing Kraus
We would like to take this opportunity to thank you for your business with Kraus
USA. It is our sincere hope that you are completely satised with your experience.
We welcome any questions or comments you may have, and will be glad to assist
you in the future.
For more information about Kraus products, please visit our website at:
www.kraususa.com
Please register your new Kraus product at the following web address in order to
activate the warranty and receive the full benet of customer support:
www.kraususa.com/registration
Sincerely,
Kraus Customer Service Department

2
Prior to Installation:
•Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-
775-0703 for a replacement
•Turn o the hot and cold water supply at the angle stops and turn on the old
faucet to release any built up pressure. Remove existing faucet. Clean sink or
countertop to remove any debris, plumber’s putty, or silicone
•
•Place bucket under angle stops. Turn on to flush any debris prior to installing new
plumbing. Shut off angle stops
•Pre-drilled hole size requirement: 1-3/8” (min) – 1-1/2” (max)
•Max countertop thickness without deck plate: 1-1/2”
•Max countertop thickness with deck plate: 1”
Without deck plate:
With deck plate:
1/16” (1mm) min.
1-1/2” (38 mm) max.
Ø 1-3/8” (35 mm) min.
Ø 1-1/2” (38 mm) max.
1/16” (1mm) min.
1” (25.4 mm) max.
Ø 1-3/8” (35 mm) min.
Ø 1-1/2” (38 mm) max.
1
2
Designated Mark
Hot
Upward
Black
Cold
1A 1B
234
567
G
G
EEF
G
G
G
G
F
F
F
E
E
H
E
E
A
A
I
B
J
D
D
CD
G
Half Moon Locking Nuts Half Moon Locking Nuts
Rubber Caps
Tools you will need:
Adjustable Wrench Safety Goggles Bucket Silicone Sealant
6 5/8”
5 4/5”
3/8”
(10mm)
7/8”
19.7
º
(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
3 3/4”
(168mm)
(147.3mm)
(96mm)
∅ 1 3/4”
(∅ 45mm)
∅ 1 15/16”
(∅ 50mm)
9/16”-18UNEF
27mm ~ 41.3mm 1 1/16” ~ 1 5/8”
∅ 1 15/16”
(∅ 50mm)
12 7/16”
(316mm)
1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
Adjustable wrench Phillips screwdriver
Tools You Will Need
Hex wrenchSilicone Sealant
A
I
D
J
F
B
G
C
H
E

3
B
A
C
D
J
F
I
H
G
E
Diagram and Parts List
A. Spray Head
B. Faucet Body
C. Deck & Putty Plate
D. Base
E. Spray Hose
F. Supply Hose
G. Hot & Cold Waterlines
H. Weight
I. Quick Connect
J. Hex Wrench Set
J1. 2.5mm
J2. 4mm

4
9/16-24 UNEF
(3/8” Compression)
Check Value
8.7”
(221mm)
2.4”
(62mm)
7.3”
(186mm)
8.2”
(208mm)
15.75”
(400mm)
10.25”
(260mm)
4.31”
(109mm)
10.5”
(267mm)
0.06”~1.2”
(1mm~30mm)
1.6”
(40mm)
24.44”
(620mm)
15º
Faucet Dimensions

5
Step 1A: Install base without deck & putty plate
Insert base (D) into sink or
countertop with “FR↑NT” facing
forward. Tighten screws on base
(D) with 4mm hex wrench (J)
until base is secure on sink or
countertop
Step 1B: Install base with deck & putty plate
Place a bead of clear silicone
sealant (not included) around the
edge of the putty plate (C). Secure
deck & putty plate (C) on sink or
countertop. Insert base (D) into
hole of deck & putty plate (C) with
“FR↑NT” facing forward. Tighten
screws on base (D) with 4mm hex
wrench (J) until base is secure on
deck & putty plate (C)
Without deck plate:
With deck plate:
1/16” (1mm) min.
1-1/2” (38 mm) max.
Ø 1-3/8” (35 mm) min.
Ø 1-1/2” (38 mm) max.
1/16” (1mm) min.
1” (25.4 mm) max.
Ø 1-3/8” (35 mm) min.
Ø 1-1/2” (38 mm) max.
1
2
Designated Mark
Hot
Upward
Black
Cold
1A 1B
234
567
G
G
EEF
G
G
G
G
F
F
F
E
E
H
E
E
A
A
I
B
J
D
D
CD
G
Half Moon Locking Nuts
Half Moon Locking Nuts
Rubber Caps
Without deck plate:
With deck plate:
1/16” (1mm) min.
1-1/2” (38 mm) max.
Ø 1-3/8” (35 mm) min.
Ø 1-1/2” (38 mm) max.
1/16” (1mm) min.
1” (25.4 mm) max.
Ø 1-3/8” (35 mm) min.
Ø 1-1/2” (38 mm) max.
1
2
Designated Mark
Hot
Upward
Black
Cold
1A 1B
234
567
G
G
EEF
G
G
G
G
F
F
F
E
E
H
E
E
A
A
I
B
J
D
D
CD
G
Half Moon Locking Nuts
Half Moon Locking Nuts
Rubber Caps
Installer Tip: Rotate the two
half-moon shaped locking
nuts inward before inserting
base (D) into deck plate (C)
Installer Tip: Rotate the
two half-moon shaped
locking nuts inward before
inserting base (D) into sink or
countertop
Please Note: After base (D) is
secure, remove clip

6
Step 2: Install faucet
Step 3: Secure faucet
Remove Quick Connect (I)
from spray hose (E). Insert
spray hose (E) into small hole
of base (D). Insert hot & cold
waterlines and supply hose
(F), one by one, in large hole
of base
Align arrow on faucet body (B)
with arrow on base (D). Attach
faucet body (B) to base (D) and
turn counter-clockwise. Secure
faucet body (B) by tightening
the set screw with 2.5mm hex
wrench (J)
D
G
G
G
G
G
B
D
J
F
F
F
I
I
EI
F
E
G
Hot Cold
Designated Mark
E
E
E
A
A
H
Rubber Cap
D
G
G
G
G
G
B
D
J
F
F
F
I
I
EI
F
E
G
Hot Cold
Designated Mark
E
E
E
A
A
H
Rubber Cap
Installer Tip: Please loosen
set screw from faucet
body (B) prior to securing
to base (D)

7
Step 4: Connect waterlines to main valve
Step 5: Connect quick connect
Thread hot & cold waterlines
(G) onto angle stops. Tighten
with adjustable wrench until
snug. Turn on the angle stops
and check for leaks (DO NOT
TURN FAUCET ON)
Attach Quick Connect (I) to
spray hose (E). Attach the other
end onto the supply hose (F)
until you hear a click
Installer Tip: Tug on the
spray hose (E) moderately to
ensure connection is secure
Installer Tip: Please remove
rubber cap from supply
hose (F) prior to installing
quick connect (I)
D
G
G
G
G
G
B
D
J
F
F
F
I
I
EI
F
E
G
Hot Cold
Designated Mark
E
E
E
A
A
H
Rubber Cap
D
G
G
G
G
G
B
D
J
F
F
F
I
I
EI
F
E
G
Hot Cold
Designated Mark
E
E
E
A
A
H
Rubber Cap
D
G
G
G
G
G
B
D
J
F
F
F
I
I
EI
F
E
G
Hot Cold
Designated Mark
E
E
E
A
A
H
Rubber Cap

8
Step 6: Install weight
Step 7: Flush faucet
Attach weight (H) on the
designated mark on the spray
hose (E)
Remove spray head (A). Hold tip
of spray hose (E). Turn faucet on
for 1 minute to ush any debris.
Reconnect spray head (A)
D
G
G
G
G
G
B
D
J
F
F
F
I
I
EI
F
E
G
Hot Cold
Designated Mark
E
E
E
A
A
H
Rubber Cap
D
G
G
G
G
G
B
D
J
F
F
F
I
I
EI
F
E
G
Hot Cold
Designated Mark
E
E
E
A
A
H
Rubber Cap
D
G
G
G
G
G
B
D
J
F
F
F
I
I
EI
F
E
G
Hot Cold
Designated Mark
E
E
E
A
A
H
Rubber Cap

9
Replacement Part List
1
7
9
2
6
10
8
5
4
3
11
13
14
12
1. A Index Button
B Set Screw
2. Metal Handle
3. Cartridge Cover
4. Locking Nut
5. Cartridge
6. Spray Head
7. Set Screw
8. Quick Connect Assembly
9. Spray Hose
10. Weight
11. Cover & Putty Plate
12. Base
13. Hex Wrench 2.5mm
14. Hex Wrench 4mm

10
Trouble - Shooting
If you have followed the instructions carefully and your faucet still does not work
properly, take the following corrective steps:
PROBLEM CAUSE ACTION
Leaking from spray
hose
Quick Connect (8) may
be installed incorrectly
Remove Quick Connect
(8) from spray hose (9)
and reinstall. Make sure
you hear a click when
you install it on the spray
hose (9)
Water will not shut off
completely
Cartridge (5) may
need to be adjusted or
replaced
Remove index button
(1A). Loosen set screw
(1B) with 2.5mm hex
wrench (13). Remove
metal handle (2).
Remove cartridge
cover (3) by hand only.
Remove locking nut
(4) with an adjustable
wrench. Remove
ceramic disc cartridge
(5). Check for cracks
Hose does not retract Weight (10) may be
installed incorrectly
Readjust weight (10) on
the hose (9). Make sure
it is installed on the
designated mark on the
hose (9)
Low flow Quick Connect (8) may
be clogged with debris
Remove Quick Connect
(8) from hoses. Soak in
50/50 solution of warm
water and vinegar for 5
minutes, then reinstall

11
Care & Maintenance
*To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth
2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary
*This installation manual is subject to change without further notice.
1
10
279
10 31/32”
Minimum distance 90mm
Less than 90mm
Cold Water
32 3/32”
Ø35~Ø38
1
23
10
9
11
12 13
Hexagon Nut
Hot
Water
Cold
Water
2 3
1
45
7
6
8
45
67
8
Ø1 3/8”~Ø1 1/2”
815
194
7 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open Left
Hot Water
Push
25˚ 90˚
12
13
8
7
Ø35~Ø38
Max35
217
8 17/32”
Max1 3/8”
9
11
12 13
2
3
4
5
6
7
8

12
Codes/Standards Applicable:
Meets ASME A112.18.1M/A112.18.1
1.75gpm 6.6L/min maximum
GREEN
Water Eciency
LEAD FREE
IAPMOR&T
TM
NSF/ANSI 61-9
NSF/ANSI 372
KRAUS LIMITED LIFETIME WARRANTY
This product has been manufactured and tested to the highest quality standards
by Kraus USA Inc. (“Kraus”). We offer our customers thoughtfully crafted fixtures
& accessories, engineered for enduring performance over years of use.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original purchaser only. This warranty is not
transferable, between homes or owners and is only applicable to residential use.
WHAT IS COVERED BY THE WARRANTY
Kraus warranties this product against defects due to material or craftsmanship
error during the warranty period: Kraus will provide replacement parts at
no charge, or at its option, replace any product or part of the product that is
deemed defective, under normal installation, use, service and maintenance. If
Kraus is unable to provide a replacement and repair is not practical or cannot
be made in timely fashion, Kraus may elect to refund the purchase price in
exchange for the return of the product.
CONDITIONS AND EXCLUSIONS
Like other home fixtures, Kraus products will require light maintenance to en-
sure proper function. We provide you with complete knowledge to perform this
maintenance and can also recommend resources if you are unable to fulfill this
service.
A. Kraus will not be responsible for product failures due to lack of maintenance
or proper use. Please read your care and maintenance documentation to deter-
mine the limits of proper use.
B. The original sales receipt, order number, and/or proof of purchase must be
presented at the time of the warranty claim, without exception, for this warranty
to be applied to all Kraus products.

13
C. Kraus recommends installing all Kraus products with a licensed, professional
plumber. Kraus will not be held responsible for any damage or product failure
due to improper installation, misuse, or failure to use a licensed professional.
Please read your care and maintenance documentation to determine the limits
of proper use.
D. Commercial use will automatically void this warranty.
E. This warranty is not applicable to Kraus products purchased from an unau-
thorized seller. For a complete list of authorized sellers please visit http://www.
kraususa.com/where-to-buy.html
NONAPPLICABILITY OF THIS WARRANTY
By the purchase and use of our products, you agree that Kraus is not liable
for incidental, consequential or special damages associated with the return,
replacement, installation or use of your product. This includes freight costs,
cartridge replacement, labor, travel time, lost profit, home damages and other
contingent liabilities and costs (including, without limitation, costs associated
with experts, investigations, analyses, attorneys and other professionals and
services). The Kraus warranty is a comprehensive and explicit limit of liability,
and all items outside of it are not addressable by or the responsibility of
Kraus. Certain states have variances regarding implied warranties and in those
situations we remain fully compliant.
KRAUS USA Inc. makes no implication that products comply with any or all local
building or plumbing codes. It is the consumer’s responsibility to determine
local code compliance. This warranty extends to the original purchaser and first
consumer.

14
If you are a homeowner please contact a Kraus Customer Service
Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
Toll-free 800-775-0703
[email protected]
If you are a plumbing contractor or trade professional please contact a Kraus
Pro Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8955
Proser[email protected]
If you are an Authorized Partner please contact a Partner Support
Representative at:
Kraus USA, Inc.
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8954
[e-mail]
In requesting warranty service, please be ready to provide:
1. Proof of purchase.
2. A description of the problem.
HELP LINE
Our customer service hours are Monday – Friday, 9am – 8pm EST.
Be sure to visit our website at www.kraususa.com

www.kraususa.com