Kubota WSM GR2100EC Instruction manual

GR2100EC
WORKSHOP MANUAL
KiSC issued 04, 2006 A

TO THE READER
This Workshop Manual has been prepared to provide servicing personnel with information on the mechanism,
service and maintenance of KUBOTA GR2100EC. It is divided into three parts, "General", "Mechanism" and
"Servicing".
Information on the product identification, the general precautions, maintenance check list, check and maintenance
and special tools are described.
Information on the construction and function are included. This part should be understood before proceeding with
troubleshooting, disassembling and servicing.
Information on the troubleshooting, servicing specification lists, tightening torque, checking and adjusting,
disassembling and assembling, and servicing which cover procedures, precautions, factory specifications and
allowable limits.
All information illustrations and specifications contained in this manual are based on the latest product information
available at the time of publication.
The right is reserved to make changes in all information at any time without notice.
Due to covering many models of this manual, information or picture being used have not been specified as one
model.
KUBOTA Corporation 2005
BGeneral
BMechanism
BServicing
April 2005
0000010040E
KiSC issued 04, 2006 A

GR2100EC, WSM SAFETY INSTRUCTIONS
1
BEFORE SERVICING AND REPAIRING
ARead all instructions and safety instructions in this
manual and on your machine safety decals.
AClean the work area and machine.
APark the machine on a firm and level ground, and set
the parking brake.
ALower the implement to the ground.
AStop the engine, and remove the key
ADisconnect the battery negative cable
AHang a "DO NOT OPERATE" tag in operator
station.
SAFETY STARTING
ADo not start the engine by shorting across starter
terminals or bypassing the safety start switch.
ADo not alter or remove any part of machine safety
system.
ABefore starting the engine, make sure that all shift
levers are in neutral positions or in disengaged
positions.
ANever start the engine while standing on ground.
Start the engine only from operator's seat.
This symbol, the industry's "Safety Alert Symbol" is used throughout this manual and on labels on the machine
itself to warn of the possibility of personal injury. Read these instructions carefully.It is essential that you read the
instructions and safety regulations before you attempt to repair or use this unit.
AIndicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
AIndicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
AIndicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
AIndicates that equipment or property damage could result if instructions are not followed.
AGives helpful information.
0000000752E
0000000753E
0000000754E
KiSC issued 04, 2006 A

GR2100EC, WSM SAFETY INSTRUCTIONS
2
SAFETY WORKING
ADo not work on the machine while under the
influence of alcohol, medication, or other substances
or while fatigued.
AWear close fitting clothing and safety equipment
appropriate to the job.
AUse tools appropriate to the work. Makeshift tools,
parts, and procedures are not recommended.
AWhen servicing is performed together by two or
more persons, take care to perform all work safely.
ADo not work under the machine that is supported
solely by a jack. Always support the machine by
safety stands.
ADo not touch the rotating or hot parts while the
engine is running.
ANever remove the radiator cap while the engine is
running, or immediately after stopping. Otherwise,
hot water will spout out from radiator. Only remove
radiator cap when cool enough to touch with bare
hands. Slowly loosen the cap to first stop to relieve
pressure before removing completely.
AEscaping fluid (fuel or hydraulic oil) under pressure
can penetrate the skin causing serious injury.
Relieve pressure before disconnecting hydraulic or
fuel lines. Tighten all connections before applying
pressure.
AVOID FIRES
AFuel is extremely flammable and explosive under
certain conditions. Do not smoke or allow flames or
sparks in your working area.
ATo avoid sparks from an accidental short circuit,
always disconnect the battery negative cable first
and connect it last.
ABattery gas can explode. Keep sparks and open
flame away from the top of battery, especially when
charging the battery.
AMake sure that no fuel has been spilled on the
engine.
0000000755E
0000000756E
KiSC issued 04, 2006 A

GR2100EC, WSM SAFETY INSTRUCTIONS
3
VENTILATE WORK AREA
AIf the engine must be running to do some work, make
sure the area is well ventilated. Never run the engine
in a closed area. The exhaust gas contains
poisonous carbon monoxide.
PREVENT ACID BURNS
ASulfuric acid in battery electrolyte is poisonous. It is
strong enough to burn skin, clothing and cause
blindness if splashed into eyes. Keep electrolyte
away from eyes, hands and clothing. If you spill
electrolyte on yourself, flush with water, and get
medical attention immediately.
DISPOSE OF FLUIDS PROPERLY
ADo not pour fluids into the ground, down a drain, or
into a stream, pond, or lake. Observe relevant
environmental protection regulations when
disposing of oil, fuel, coolant, electrolyte and other
harmful waste.
PREPARE FOR EMERGENCIES
AKeep a first aid kit and fire extinguisher handy at all
times.
AKeep emergency numbers for doctors, ambulance
service, hospital and fire department near your
telephone.
0000000757E
0000000758E
0000000759E
0000000760E
KiSC issued 04, 2006 A

GR2100EC, WSM SAFETY INSTRUCTIONS
4
The following safety decals are installed on the machine. If a decal becomes damaged, illegible or is not
on the machine, replace it. The decal part number is listed in the parts list.
SAFETY DECALS
0000009636E
KiSC issued 04, 2006 A

GR2100EC, WSM SAFETY INSTRUCTIONS
5
0000009633E
KiSC issued 04, 2006 A

GR2100EC, WSM SAFETY INSTRUCTIONS
6
0000009634E
KiSC issued 04, 2006 A

GR2100EC, WSM SPECIFICATIONS
7
SPECIFICATIONS
Model GR2100EC
Engine
Maker KUBOTA
Model D782-E2-GX
Type Indirect injection. Vertical, water-cooled, 4-cycle diesel
Number of cylinders 3
Bore and stroke 67 x 73.6 mm (2.64 x 2.90 in.)
Total displacement 778 (47.46 cu.in.)
Engine gross power (DIN) 15.6 kW (20.9 HP)
Rated revolution 50 r/s [3000 (rpm)]
Battery 51R (12 V, 450CCA)
Starting system Cell starter (with glow plug)
Lubrication system Forced lubrication by trochoidal pump
Cooling system Pressurized radiator, forced circulation with water pump
Fuel Diesel fuel No.2-D [above -10 (14 )],
Diesel fuel No.1-D [below -10 (14 )]
Capacities
Fuel tank 18 L (4.8 U.S.gals, 4.0 lmp.gals)
Engine crankcase (with filter) 2.8 L (2.96 U.S.qts., 2.46 lmp.qts.)
Engine coolant (with recovery tank) 2.35 L (2.48 U.S.qts., 2.07 lmp.qts.)
Transmission case 3.3 L (0.87 U.S.gals., 0.73 lmp.gals.)
Front axle case 1.9 L (0.50 U.S.gals., 0.42 lmp.gals.)
Dimensions
Overall length (with grass catcher) 2540 mm (100.0 in.)
Overall width 1280 mm (50.4 in.)
Overall height 1230 mm (48.4 in.)
Wheel base 1280 mm (50.4 in.)
Tread Front 825 mm (32.5 in.)
Rear 800 mm (31.5 in.)
Weight (without mower and grass catcher) 360 kg (794 lbs)
Traveling system
Tires Front 16 x 7.50 - 8, 4PR
Rear 23 x 10.50 - 12, 4PR
Steering Full hydraulic power steering (Glide Steer)
Transmission Hydrostatic transmission
Brake Internal expanding brake
Traveling speed Forward 0.0 to 10.0 km/h (0.0 to 6.2 mph)
Reverse 0.0 to 5.0 km/h (0.0 to 3.1 mph)
PTO system Clutch Mechanical wet multi discs
PTO brake Wet multi discs
NOTE: *Manufacture's estimate
The company reserves the right to change the specifications without notice.
0000010042E
KiSC issued 04, 2006 A

GR2100EC, WSM SPECIFICATIONS
8
Model RCK48GR
Mower
Cutting width 1219 mm (48.0 in.)
Cutting height 25 to 102 mm (1 to 4 in.)
Adjustment of cutting height Dial gauge
Mounting method Quick joint, Parallel linkage
Weight (Approx.) 80 kg (176 lbs)
Dimensions
Total length 871 mm (34.3 in.)
Total width 1270 mm (50.0 in.)
Total height 305 mm (12.0 in.)
Discharge direction Rear
Gear box oil 0.40 L (0.42 U.S.qts, 0.35 Imp.qts)
Model GCK450GR
Grass catcher Container capacity 450 L (118.9 U.S.gals, 99.0 Imp.gals)
Weight (Approx.) 50 kg (110 lbs)
NOTE: *Manufacture's estimate
The company reserves the right to change the specifications without notice.
0000010041E
KiSC issued 04, 2006 A