KwikBoost EdgePower KBEP-CGR User manual

Tighten bolt until clamp fits snugly on desk.
IMPORTANT: Do not over-tighten bolt.
3
1
Open Clamp-On Desktop Charging Unit
clamp by loosening 8 mm bolt.
2A B
Test clamp fit by sliding clamp over edge of desk or table.
Ensure outer edge of desk fully reaches inner edge of clamp.
Ensure there is adequate clearance to insert and remove
Rechargeable Battery.
INSTRUCTIONS
8mm Hex Wrench
Tools Required:
CLAMPON DESKTOP
CHARGING UNIT
KBEPCGR
In the Box:
Clamp-On
Desktop Charging Unit 8 mm Hex Wrench
Insert Rechargeable Battery into Clamp-On Desktop Charging Unit.
IMPORTANT: Battery must be fully charged before first use.
4
Ships / Sold Separately:
Rechargeable Battery Battery Charging Options

Press power button on top of clamp to activate
AC outlet.
6
7
IMPORTANT: Plug a maximum of one device into each
corresponding outlet/port. Do not use a splitter to plug multiple
devices into one outlet and/or port, as this will damage the
Rechargeable Battery and Clamp-On Desktop Charging Unit.
TROUBLESHOOTING
Power Button Flashing Green*
1. Reset Clamp-On Desktop
Charging Unit by unplugging
device(s) and pressing power
button.
2. Plug device in again. If power
button continues to flash,
device is not compatible with
EdgePower and should not
be used.
*Indicates a safety feature has
been triggerd by a device.
Device Not Charging when
Plugged into AC Outlet:
1. Confirm power button
has been pressed and
green light is on.
2. Check the Rechargeable
Battery’s indicator lights for
power level.
3. Recharge Battery if one
or fewer indicator lights
are illuminated.
Device Not Charging when
Plugged into USB Ports.
1. Check the Rechargeable
Battery’s indicator lights for
power level.
2. Recharge Battery if one or
fewer indicator lights are
illuminated.
Plug devices into corresponding
AC outlet and USB ports.
USB-C and USB-A ports will immediately
begin powering devices.
USB-C
USB-A
AC OUTLET
5
Press power button on end of Rechargeable Battery to
activate indicator lights and monitor power consumption.
When only one LED is illuminated on Battery, replace with a
fully-charged Battery from Base Charging Station.

Model : KBEP-CGR
Modèle : KBEP-CGR
Input : 18-25.2Vdc, 5.2A Max. (For battery pack)
Entrée : 18-25.2Vdc, 5.2A Max. ( Pour batterie)
AC Output: 110Vac, 0.8A
DC Output: USB Output: 5Vdc, 2.4A; (Support QC3.0)
Type-C Output: 5Vdc, 3A or 9Vdc, 2A or 12Vdc, 1.5A 18W Max. (Support PD)
USB and Type-C Total Output: 20W Max.
Sortie CA : 110Vca, 0.8A
DC Sortie : USB Sortie : 5Vdc, 2.4A; (Prise en charge QC3.0)
Type-C Sortie: 5Vdc. 3A or 9Vdc. 2A or 12Vdc. 1.5A 18W Max. (Soutien PD)
USB and Type-C Total Sortie: 20W Max.
1. Product maximum service temperature 35°C, suitable for use
below 5000meters above sea level.
Température de fonctionnement maximale du produit 35°C, adaptée
á une utilisation sous les 5000 mètres au-dessus du niveau de la mer.
2. Candles and other open sources of fire shall not be placed on the product.
Les bougies et autres sources de feu ouvertes ne doivent pas entrer en
contact avec le produit.
3. If you want to clean the equipment, please use a dry cloth or dry brush to clean.
Si vous souhaitez nettoyer l’équipement, veuillez utiliser un chiffon sec
ou une brosse sèche pour le nettoyer.
6. Warning: See instruction manual for use in countries other than the U.S.A.
or equivalent.
Note: This product should be used with battery pack model KBEP-BAT.
Manufacturer: Dong Guan Techoss electronic technology Co., Ltd.
Fabricant: Dong Guan Techoss electronic technology Co., Ltd.
Made in China
Fabriqué en Chine
Safety Instructions
Directives de sécurité
5. Class II equipment.
Matériel de classe II.
4. For indoor use only.
Pour utilisation à l’ intérieur seulement.
MAN-KBEP-CGR