KZN Solar GT-SKR010B User manual

- 1 -
Air Source Heat Pump Water Heater
Domestic Series
Instruction Manual
Model: GT-SKR010B
GT-SKR015B
GT-SKR020B
GT-SKR030B
◆The instructions in this manual are for the use of qualified individuals specially
trained and experienced in the installation and maintenance of this type of equipment.
◆ Persons not qualified shall not attempt to install, service, or maintain this equipment.
◆Please read the manual carefully before installation.
◆Please keep this manual well for future reference.

- 2 -
TABLE OF CONTENTS
Part I: General Information··················································································································3
Working Principle·························································································································4
Features of heat pump·················································································································5
Part II: Unit exploded view···················································································································6
Part III: Installation & Application········································································································7
Transportation····························································································································7
Installation Location requirement·······························································································7
Installation··································································································································7
Accessories································································································································8
Piping system·····························································································································8
Electrical connection···················································································································9
The specification of power ·········································································································10
How to install the temperature sensor to water tank··································································10
Trial operation····························································································································11
How to drain air··························································································································11
Part IV: Control System························································································································13
Part V: Maintenance······························································································································16
Part VI: Trouble shooting······················································································································17
Part VII: Wiring diagram························································································································19
Disposal········································································································································20

- 3 -
Part I: General Information
1.1 Function description
Air source heat pump water heater is used to heat water for domestic hot water or commercial hot
water, etc.
1.2 Important Information
For your own security, and to ensure proper operation of the unit, this heat pump unit must be
installed and repaired by qualified technician, not consumer himself.
A leakage protection switch must be installed near the heat pump in an accessible place.
Do not use any damaged wires and switches, If found ( to be damaged), replace it immediately.
Do not open the electrical box without shutting off all power sources to the heat pump.
When transporting the heat pump, ensure that it is not upside down and not tilted more than 45°in
any direction.
Before performing any maintenance on the unit you must turn it off first and shut off the power to the
unit.
This unit is designed for outdoor installation, do not install it in an closed area.
Do not install the unit in places where there are any inflammable or explosive materials.
Do not restrict or block the air intake or outlet of the unit.
When the unit is not used for a long time, please switch it off and disconnect the power supply.
Drain the unit when ambient temperature is lower than 0℃
When power failure occurs and lasts for more than 5 hours with the ambient temperature lower than
2℃, please drain the unit to prevent the formulation of ice in it.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience or knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
Respect safety distance between the unit and other equipment or structures. Guarantee adequate
space for access to the unit for maintenance and/or service operations.
Power supply: the cross section of the electrical cables must be adequate for the power of the unit

- 4 -
and the power supply voltage must correspond with the value indicated on the respective units. All
units must be earthed in conformity with legislation in force in the country concerned.
1.3 About heat pump
Heat Pump unit is a new technology and is regarded as the lastest generation among the various water
heating/cooling methods. It surpasses coal, electrical, gas and solar water heating, offering a better solution
for energy saving and environmental protection.
With the advantage of high energy efficiency ratio and pollution-free, heat pump is widely used all over the
world. Compared to electrical heating, consuming the same quantity of electricity, heat pump water heater
makes as 3～5 times of hot water as the former does.
1.4 Working principle
The basic principle of how a heat pump works is simple. Take air source heat pump for example, it works
just like air conditioner in cooling mode, however, in heating mode, the refrigerant flow is reversed and heat
is extracted from the outside air to heat your home. So the purpose of a heat pump is to absorb heat in one
place where it is plentiful, then to transport and release it in another location where it can be used for space
or water heating.
In order to absorb and release the heat into and from the refrigerant, we exploit the ability of the refrigerant
fluid to boil from a liquid to a vapor and then to condense back into a liquid. This is a continual process while
the compressor is running and circulating the refrigerant
1. The refrigerant in system extracts free heat energy from ourside air through fin-coil evaporator.
2. The refrigerant is compressed to a high-temp. & high-pressure gas by compressor.
3. Heat energy transferred to water through tube-in-shell heat exchanger.
4. The refrigerant in system restores to low-energy condition
5. The cycle is repeated.

- 5 -
1.5 Features of heat pump water heater
1）Wide application
It can be widely used in villas, factories, schools, hospitals, hotels, restaurant, swimming pools and
spas, bath centers, laundries, etc.
2）More Safety
Water and electricity are completely isolated, No electric shock problem, more secure than traditional
electrical water heaters.
No fuel tubes and storage, no potential danger from oil leakage, fire, explosion, etc.
A full range of protection including compressor delay protection, water-pressure check switch, high &
low pressure protection, supper heating protection, Anti-phase and open-phase protection, high
temperature protection, etc.
3）Energy-saving
It provides the same amount of hot water at 1/4 cost of electrical water heaters, heat pump water heater
can save your bill every day.
4）Super-Sized evaporator coil
Hydrophilic aluminum fin and rifled copper coil, it has higher performance in cold weather.
5) High efficiency heat exchanger
6) World famous Compressor
It adopts the world famous brand compressor---“Copeland”, “Panasonic”, “Sanyo”, unmatched reliability,
quiet operation, energy-saving and environmental-friendly.
7）Monoblock design, convenient installation, nice appearance.
8）All-weather running
It supplies hot water no matter in a rainy day, snowy day or at night.
9）Running automatically
It is microcomputer controlled, with timer function, it can automatically start up and stop according to the
water temperature and other running conditions you set, no need for a supervisor.
10）Environmental friendly
Environment-friendly, free of pollutions, it reduces the global green house effect.

- 6 -
Part II Unit Exploded View
20 Protection grid 10 Right panel
19 Wind circulation grid 9 Circulation water pump
18 Evaporator 8 compressor
17 Fan motor 7 High pressure switch
16 Fan 6 Rear panel
15 Front panel 5 Low pressure switch
14 Tube-in-shell heat exchanger 4 Four way valve
13 filter 3 Electronic expansion valve
12 Bottom sheet 2 Partition sheet
11 Electric box 1 Top panel

- 7 -
Part III Installation & Application
3.1 Transportation
When transporting the heat pump, ensure that it is not tilted more than 45°in any direction.
3.2 Installation Location Requirement
This unit is designed for outdoor installation, do not install it in an enclosed area.
It is very important to select a proper position for the unit, you should consider the followings:
● The space for installation should be large enough and well ventilated
● The installation position should be close to drainage channel or vent to facilitate water discharge.
● Choose a smooth, horizontal position where it can stand
the weight of the unit, and it won’t increase noise and
vibration as well, or you can use bracket to fix it on the
wall, if necessary.
● Do not install the unit in place where there is pollution,
accumulation of dirt or fallen leaves.
● There should not be inflammable or explosive materials
close to the unit.
3.3 Installation
3.3.1 Install the outdoor unit
a. Mount the unit on the selected base and install the 4 black
shockproof rubber pads under the 4 sheet of the unit to reduce
vibration and sound transmission to the base. (Fig 1.1). For
GT-SKR010B, GT-SKR015B, GT-SKR020B, users may use
brackets to install the unit on wall (Fig 1.2)
fig.1.1
Shockproof rubber pad Base
HeatPump
<45°
fig 1.2

- 8 -
Front
Condensate
connector
b. Connect the condensate connector to the
draining hole on the bottom sheet. (Fig 2)
3.3.2 Accessories
No Item Quantity
1 Instruction Manual 1
2 Condensate connector 1
3 Shockproof rubber pads or Brackets 1 set
3.3.3 Piping Systems for pressurized type water tank
(circulating water pump inside the unit)
water outlet
water inlet
hot water output
3
2
1
4
water outlet
water inlet
5
6
to user's hot water system
Heat pump
1
2
temperature sensor
union
wye strainer
City water
Installation Instruction
temperature sensor
Pressurized type
water tank
6
5
4
3
（220V）
Electrical cable
connection
check valve
gate valve
relief valve
Legend
Pressurized type water tank
Remark:
1. The vertical distance between heat pump unit and water tank should be less than 3m, and the total pipe
run between them should be less than 6m.
2. Make sure to install a wye strainer before water inlet of the unit to avoid clogging of the system. For
pressurized type water tank, It’s an essential requirement to install a relief valve on water tank.
3. Fix the temperature sensor of the water tank well into the connection to avoid falling down as the failure
may cause overheating protection or system halted.
fig 2

- 9 -
4. In case the wire for the temperature sensor is not long enough, It is suggested to use screening wire and
bind it with electrical adhesive type in order to avoid oxidation or loose connection as it may affect the
transfer of data.
5. The circulation pipes and valves must be well insulated, otherwise it’ll loose heat or cause frozen problem.
6. Wire the power of the heat pump water heater (refer to wiring diagram), make sure the voltage is stable
when give a trial run to the unit.
3.3.4 Electrical Connection
For your own security, and to ensure proper operation of the unit, this heat pump unit must be
installed and repaired by qualified technician, not consumer himself.
A leakage protection switch must be installed near the heat pump in an accessible place.
Do not use any damaged wires and switches, If found (to be damaged), replace it immediately.
Do not open the electrical box without shutting off all power sources to the heat pump.
zAll the wiring must meet the electrical safety requirement and conducted by qualified electricians.
zEnsure that there is a good earth connection for the power. Do not disconnect the earth connection of the
power in any condition.
zEnsure that the heat pump water heater is well connected to the earth.
zOffer an separate power which meets rated requirements for the heat pump water heater
zWhen the water heater connects to the electricity network, there must be a short-circuit protection.
zChoose the suited type of wires when use the power outdoor.
zDo not use the main power switch to control the start/stop of the unit.
zAfter installation, double check before connect it to the power.
leakage
protection
switch
Power
switch
Electricity grid
N
L
PCB
N
L
Power supply
connection
push
Open the control panel when relocate it.
Make sure to install a waterproof box to guarantee safety.

- 10 -
The Specification of Power
Type GT-SKR010B/015B GT-SKR020B GT-SKR030B
Power supply 220-240V～,50Hz
Circuit Breaker/Fuse(A) 25/20 30/25 40/35
Power wiring (mm2) 3×2.5 3×2.5 3×4.0
Ground wiring (mm2) 2.5 2.5 4.0
3.3.5 How to install the water tank temperature sensor
a. Opening the front sheet to find the water tank temperature sensor (fig 3)
b. Install it to the water tank (fig 4)
fig 3
fig 4
N
L
PCB
Control Panel
Water tank temp. sensor
Water Outlet
Water Inlet
Water Pump
NL
PCB
temperature sensor
Install the sensor to water tank.

- 11 -
3.4 Trial Operation
zTo ensure that start-up is performed correctly, it should only be operated by qualified technician.
zThe heat pump water heater is designed according to the conditions as follows: the range of
ambient temperature is -10～43℃and the range of water pressure is 0.15～0.8Mpa. The range of
water outlet temp. is 28～60℃
●Make sure the piping system and water tank is filled up with water before commissioning.
3.4.1 Preparation
The following items need to be checked prior to start-up:
a. The heat pump must be fully connected.
b. All valves that could impair the proper flow of the heating water in the heating circuit must be open.
c. The air intake and air outlet paths must be clear.
d. The ventilator must turn in the direction indicated by the arrow.
e. Ensure the condensate outflow functions.
f. Open the gate valve to fill the piping system and water tank, then discharge air in piping system and
water tank (refer to the following instruction)
To discharge air in water pump and piping system:
Step1: loosen the screw on the water pump through the hole,
Step2: Connect heat pump to power supply, then start it by pressing on controller,
Step3: Discharge air for about 15 minutes, then fasten the screw.
To discharge air out of water tank
The water tank is pressured type, after opening water refilling gate valve, it will be filled up
automatically and air in it will be discharged automatically through relief valve on hot water oulet.
3.4.2 Trial run
●Make sure the piping system and water tank is filled up with water before commissioning and air is
discharged out of the system.
● The water outlet temperature is set by the controller. When the water temperature of tank is higher
than it is set, the unit will stop running, but if lower by 5℃(default temperature difference), it may
start up automatically.
● The heat pump is started up via the heat pump control panel. After the water pump has been running
for 30 seconds, the unit starts to work, and then observe whether it works normally.
● When you restart the unit, the compressor won’t start to work until three minutes later, and this
function is designed to protect the compressor.
It’s very important
to discharge air!
unscrew it by a flat blade screwdriver
Air discharge of water pum p
Air discharge of water pump

- 12 -
3.4.3 Caution
If something happen as follows, please stop it immediately and cut the power off. You should contact with
our authorized agent or maintenance personnel, don’t repair it by yourselves. Without professional
technology, it may cause fire and you may get hurt.
● Fuse blown or protection activated frequently
● The wire and switches are heated abnormally
● Abnormal sounds coming from the unit
● Abnormal smell comes out of the unit.
● Electricity leakage

- 13 -
Part IV Control System
4.1 Description of Icons
4.2 Operation Instruction
OFF ON Compressor starts running
A. Lock/Unlock the buttons
1. Lock the buttons: Under ON or OFF status, extended press button simultaneously for 5
seconds, buttons are locked, and icon is shown on the screen.
2. Unlock the buttons: Repeat the above step to unlock the buttons
B. On/Off the unit
1. Connect power to the unit, press button to turn on the unit, When compressor starts working,
icon flashes on screen.
2. When the unit is on, press button, you can turn it off.
C. Set the clock (Note: it will exit the interface when no operation for 10 seconds)
Under ON or OFF status, extended press button for 5 seconds, then press button to set
the hour, press button, then press button to set the minute, press button to exit.
①Flashing when compressor starts running
②Defrosting indication
③Showing when the unit starts running
④Auxiliary electrical heating indication (unuesd)
⑤The desired temperature
⑥Clock
⑦Measured water tank temperature
⑧Timer of turning-on the unit
⑨Timer of turning-off the unit

- 14 -
D. Set water temperature
When the unit is on, press button to set desired water tank temperature. The setting will be
saved automatically when no further operation on it for 10 seconds. The range is 28℃-60℃.
Note:
·Heat pump unit will stop running automatically when water temperature in water tank reaches desired
watertemperatureyouset.
·The unit will start running automatically when water temperature drops to a certain temperature.
( according to temperature difference you set, refer to item 05 in table 4.1)
E. Set/Cancel the timer of On/Off (Note: it will exit the interface when no operation for 10 seconds)
Note:
You can set totally three period of time for the unit to start/stop automatically. Under ON or OFF status,
Press button once, “ 1 ” flashing; Press button twice, “ 2 ” flashing; Press
button thrice, “ 3 ” flashing.
1. Set timer: (Take “ 1 ” for example)
when “ 1 ” is flashing, Press button, flashing on the screen, then press
button to set hour, Press button then press button to set minute; press button,
flashing on the screen, then press button to set hour, Press button then press
button to set minute, press button to finish setting.
2. Cancel timer: To cancel timer, just set the unit to turning-on & turning-off at the similar time, then
icon disappeared.
F. Set/Review the parameters (for technician only)
When the unit is on, extended press button to enter the interface. press button, select item
(01-08), press button, then press button to set, press button to confirm.
Table 4.1
Item Description Range Default Value Remark
01 Coil temp. to start defrosting -1～-9℃-3℃flashing
02 Coil temp. to stop defrosting 5～25℃12℃flashing
03 Time interval for defrosting 10～90 Min 45 Min flashing
04 Running time of defrosting 5-17 Min 10 Min flashing
05 Temperature difference set 2-30 9 Refer to note 1,2,3 as below
06 Temp. compensation 0-30 0
07 Return water temperature 28～60℃40℃flashing, it’s for commercial unit.
08 Ambient temp. for starting
electrical heating (unused) 0～35℃5℃
flashing, when ambient temp. is
lower than set temp. , electrical
heating functions.
Note:
1. Set the temperature difference between measured water temperature and purpose water temperature
2. By setting the temperature difference to control the unit to start up/stop automatically.

- 15 -
3. For example, the default value is 9 (that represents 5℃), when the measured temperature is lower than
desired water temperature by 5℃, the unit will start automatically. The unit will not stop until the
measured temperature reaches the desired water temperature you set.
1 equals 0.5℃, the range is 2-30.
G. Review Data
When the unit is on, shortly press button, then press button, review the actual measured data
as below:
Table 4.2
Name Ite
m
Remarks
Code of recoverable fault 01 It shows “28” when it works normally, others please refer to Table
4.3
“Mode Selection" Code Name
02 “0” circulation heating mode
Unit type 03 “0” single compressor, without phase detection
Unused 04 Spare
Coil temperature 05 Monitoring point of Defrosting temp. for compressor
Ambient temperature 06 Opening measurement of the electric expansion valve, and the
anti-freeze temperature
Water outlet temperature 07 overheating protection (70℃)
Unused 08 Spare
Water temperature in tank 09 The unit stops working automatically when temp. reaches desired
value.
Unused 10 Spare
Unused 11 Spare
Table 4.3: Recoverable faults
Fault Name Remark
“01E” Overheat protection Hydraulic pressure switch protection
“05E” Overheat protection If the water outlet temperature is highter than 70℃and lasts
for 20 seconds, the unit may stop. And when the temperature
cools down, it will restart in three minutes.
4.3 Protection
Compressor delay protection: the delay for the compressor to start/stop is three minute. The first time◆
when it is power on, it starts up in one minute.
High pressure pro◆tection: After compressor starts running and the high pressure switch interrupts for 10
seconds, the unit stops, “03E” flashing on the screen, and alarm sounds.
Low pressure protection:◆After compressor starts running for 3 minutes and the low pressure switch
interrupts for 10 seconds, the unit stops, “04E” flashing on the screen, and alarm sounds.
◆When hydraulic pressure switch interrupts, the unit stops, “01E” fault code is shown on the screen and it
won’t alarm. When the pressure recovers, the unit restarts automatically.
◆Overheating protection: when water outlet temperature is higher than 70 for 20 seconds, the℃

- 16 -
compressor stops, and when the temperature cools down to where it is set and the unit meets the
condition of stoping for three minutes, the unit restarts automatically,
Sensor fault:◆if the sensors fail, all parts stop working.
◆Auto-antifreeze: To prevent the pipes and pumps from being frozen, the unit will defrost automatically
when it meets the condition as follows: the ambient temperature is lower than 2 and the water outlet℃
temperature is lower than 10 and the circulating pump has been power℃ed off for more than 30 minutes.
The circulation pump start up for 60 seconds , then turn off. This action repeats periodically.
Part V Maintenance
Before performing any maintenance on the heat pump you must swith it off first and shut off the power to
the unit.
A well-maintained heat pump could save your energy costs. When installed and tested by a qualified
technician, heat pumps can deliver many years of dependable service and comfort. Below are some tips
you can follow to ensure that your heat pump gives you optimum performance.
1. Turn the power off when the unit is being maintained.
2. Do not use petrol, naphtha, dissolvent and any other chemicals on the unit, otherwise, it may damage the
surface. External heat pump parts can be wiped with a damp cloth and domestic cleaner.
3. Avoid leaning or putting objects on the device.
4. Keep it dry and drafty round the unit. Clean the heat exchanger regularly (usually once per 1～2 months) to
keep a good heat exchange efficiency.
5. If the unit will be shut down for a long time, you should drain the water in the pipe, turn the power off and
cover it with protective cover, Check it roundly before you start it again.
6. It is advised to use the phosphoric acid whose temperature is about 50～60℃and consistency is 15% to
clean the heat exchanger of the unit. First start the circulation pump to clean it for 3 hours, and then flush it
with tap water for three times. Do not use any amyctic detergent to clean the heat exchanger and the tank.
7. Change the installation site
If the customer wants to change the site, please contact with the dealer or the local Customer Service for
help.

- 17 -
Part VI Trouble Shooting
Table 6.1
Fault
Code
Fault Possible Causes Treatment
01E Hydraulic pressure
switch protection
(protect when
interrupts)
◇Hydraulic switch destroyed
◇Inadequate water-flow
◇There is air in the circulating
water inlet tube
◇Circulating pump destroyed
◇Water tank lack of water
◇Replace the hydraulic switch
◇Clean the wye strainer, increase the
water-flow
◇Discharge the air
◇Check and repair the pump and the
capacitor
◇Ensure the tank is fully filled and the
water pressure is over 0.15Mpa
02E Current protection ◇Over-current ◇Check the power supply
03E High pressure switch
fault (protect when
interrupts)
◇High pressure switch destroyed
◇Inadequate water-flow
◇The system is jammed, the probe
of sensor falls down
◇Circulating pump damaged
◇Excessive refrigerant
◇Some un-condensable gas in the
refrigerant system
◇Replace high pressure switch
◇Increase the flow
◇Check and clean the system, retighten
the probe
◇Check and repair the circulating pump
and the capacitor
◇Drain out the superfluous refrigerant
◇Drain out the un-condensable gas
04E Low pressure switch
fault (protect when
interrupts)
◇Low pressure switch destroyed
◇Inadequate refrigerant
◇The fins of the evaporator are
dirty
◇Replace low pressure switch
◇Leak hunting and fill in standard
quantity of refrigerant
◇Clean the fins
05E Overheating of the
outlet water
◇Clogged water line
◇water outlet temperature sensor
fault
◇Check the water system and the pump
◇Check the electric resistance of the
sensor
09E Communication error
( the control panel
can’t receive
information from the
PCB)
◇Open circuit or short circuit
between the operation panel and
PCB
◇Renovate or Replace the wire between
control panel and PCB
11E Coil sensor fault
(open circuit or short
circuit)
◇The sensor open circuit
◇The probe of the sensor falls
down
◇the sensor short circuit
◇Reconnect the wirings of the sensor
◇Retighten the probe
◇Renovate wirings and remove faults
12E Environment sensor
fault (open circuit or
short circuit)
◇The sensor open circuit
◇The probe of the sensor falls
down
◇the sensor short circuit
◇Reconnect the wirings of the sensor
◇Retighten the probe
◇Renovate wirings and remove faults
13E Water outlet sensor
fault (open circuit or
short circuit)
◇The sensor open circuit
◇The probe of the sensor falls
down
◇the sensor short circuit
◇Reconnect the wirings of the sensor
◇Retighten the probe
◇Renovate wirings and remove faults
15E Water-tank sensor
fault (open circuit or
short circuit)
◇The sensor open circuit
◇The probe of the sensor falls
down
◇the sensor short circuit
◇Reconnect the wirings of the sensor
◇Retighten the probe
◇Renovate wirings and remove faults
Note: when the fault arises, the correspondent fault code will be flashing on the screen and alarm sounds.

- 18 -
Table 6.2
Fault Condition Possible Causes Treatment
The unit doesn’t
work
◇Power failure
◇Bad connection to the power
◇Fuse blow
◇Turn off the switch, check the Power
source
◇Find the causes and renovate them
◇Replace the fuse
The pump is working
but too noisy and the
water is not cycled
◇Lack water In the system
◇There is air in the water circulation
◇Any valve in the system is not open
◇Filter stoppage
◇Check the water make-up device and
fill in with water
◇Discharge the air in the water system
◇Open all the valves
◇Clean the filter
Low heating
capacity
◇Inadequate refrigerant
◇bad insulation of the water system
◇Drying filter stoppage
◇Air side heat exchanger is
un-efficient
◇Inadequate water-flow
◇Leak hunting and fill in standard
quantity of refrigerant
◇Improve the heat insulation
◇Replace the drying filter
◇Clean the heat exchanger
◇Clean the water filter
The compressor
doesn’t work
◇Power failure
◇Compressor contactor destroyed
◇Poor connection
◇Overheating protection
◇water outlet temperature is too high
◇Inadequate water-flow
◇Check it and solve the problems
◇Replace contactor
◇Check and renovate it
◇Check and solve the problems
◇Reset a proper temperature
◇Clean the water filter and discharge the
air in the water system
The compressor
works but too noisy
◇Liquid refrigerant goes into the
compressor
◇interior components destroyed
◇Inadequate refrigeration oil
◇Check the expansion valve
◇Replace the compressor
◇Add in adequate refrigeration oil
The fan doesn’t work
◇Capacitor damaged
◇The fans are not fixed well
◇The electromotor burned out
◇Contactor destroyed
◇Replace it
◇Fix it well again
◇Replace the electromotor
◇Replace the Contactor
Compressor works
but not heating
◇Refrigerant leakage
◇Compressor fault
◇Leak hunting and fill in standard quantity
of refrigerant
◇Replace the compressor
Low water-flow
protection
◇Hydraulic switch destroyed
◇Inadequate water-flow
◇Replace the switch
◇Clean the filter and discharge the air
Excessive discharge
pressure
◇Too much refrigerant
◇Non-condensable gas in the
Refrigeration cycle
◇Inadequate water-flow
◇Draw off the superfluous refrigerant
◇Drive the gas out
◇Check the circulation and increase the
flow
Low suction
pressure
◇Drying filter stoppage
◇Lack of refrigerant
◇Excessive pressure drop in the heat
exchanger
◇Replace the filter
◇Leak hunting and fill in standard quantity
of refrigerant
◇Check the opening of electronic
expansion valve

- 19 -
Part VII Wiring Diagram
CN3
N
C0N1
L N
R
S
C
PCB
PCB
C
S
R
L N
C0N1
N
CN3
four
way
valve
high
fan
speed
low
fan
speed
circula-
ting
pump
fan pump
compressor
stage
second
stage
primary
Main Power Supply
compressor
control panel
electronic
expansion
valve
current
detection
water
tank
water
outlet
air
coil
water
tank
temp.
sensor
water
outlet
temp.
sensor
ambient
temp.
sensor
coil
temp.
sensor
transformer
high pressure
switch
low pressure
switch
GT-SKR010B Wiring Diagram
transformer
Main Power Supply
primary
second
coil air
water
outlet
water
tank current
detection
electronic
expansion
valve
control panel
low pressure
switch
high pressure
switch
compressor
stage
stage
fan pump
compressor
four
way
valve
high
fan
speed
low
fan
speed
circula-
ting
pump
GT-SKR015B/020B/030B Wiring Diagram
coil
temp.
sensor
ambient
temp.
sensor
water
outlet
temp.
sensor
water
tank
temp.
sensor
SETP
SETP
current
transformer
water flow
switch
water flow
switch

- 20 -
Disposal
Do not dispose this product as unsorted municipal waste. Collection of such waste separately for special
treatment is necessary.
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
Contact your local government for information regarding the collection systems available. If electrical
appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and
get into the food chain, damaging you health and well-being.
There won’t be a further notice if anything changes as the unit improved. V1.0-20100920-H