Specifications are subject to change without notice.
Evos®156465 Hang Glider®
J:\INSTSPEC\SPECS\184\18496100.P65
Parts List
Part# Description Qty.
154800-00 Hang Glider Rail, Specify Color .............................. 2
182712-00 Hang Glider Crossover, Specify Color .................... 1
182643-00 Curved Loop Pole, Specify Color ............................ 1
156699-00 Ball Clamp, Specify Color........................................ 2
156700-00 Ball Retainer, Specify Color..................................... 2
182368-00 Hang Glider Hardware Package........................... 1
100198-00 3/8" x 1 1/8" BHCS w/Pin, SST .................................. 4
100201-00 5/8" x 1 1/2" BHCS w/Pin, SST .................................. 4
100611-00 1/4" x 3/8" Drive Rivet, AL/SST ................................. 6
156848-00 Play It Safe Label, 8-12 Years .................................. 1
Specifications
Hang Glider Rail: Fabricatedfrom1.900"O.D. RS40 (.120"-.130" wall)
galvanized steel tubing. Finish: ProShield®, color
specified.
Curved Loop Pole: Weldment comprised of 2.375" O.D. RS20 (.095"-
.105" wall) galvanized steel tubing, and 1.029" O.D.
RS20 (.070"-.080" wall) galvanized steel tubing. Fin-
ish: ProShield, color specified.
Crossover: Weldment comprised of 1.315" O.D. RS20 (.080"-
.090"wall)galvanizedsteeltubing, 1.900" O.D. RS20
(.090"-.100"wall) galvanized steeltubing,2.375" O.D.
RS40 (.130"-.140" wall) galvanized steel tubing, 1/8"
HRPO sheet steel and 1 7/8" steel ball. Finish:
ProShield, color specified.
Ball Clamp/
Ball Retainer: Cast from 535 almag. Finish: ProShield, color speci-
fied.
Fasteners: Primary fasteners shall be socketed and pinned
tamperproofindesign, stainless steel(SST)perASTM
F 879 unless otherwise indicated (see specific prod-
uct installation/specifications).
InstallationTime: Approx. 3 man hours
Concrete Req.: Approx. 3.75 cu. ft.
Area Req.: 6' (1830 mm) minimum use zone
Weight: 162 lbs.
Fall Height: 81" (2060 mm)
Installation Instructions
1) (Direct Bury) Refer to the Site Plan for footing locations.
2) Attach ball retainers to 5" round clamps using 5/8" x 1 1/2" BHCS w/pin.
Attach crossover to ball retainers using ball clamps and 3/8" x 1 1/8"
BHCS w/pin. Refer to the Crossover Attachment Detail. NOTE: 5"
Round clamps may need to be turned, or moved up or down to con-
nect crossover and position hang glider properly. Check to make
sure crossover is level, if not adjust 5" round clamps.
3) Insert end of curved loop pole into crossover stub. With curved loop
pole steps level, drill through holes in crossover tube into curved
loop pole with a 1/4" or "F" (only) drill bit. Insert 1/4" x 3/8" rivets into
holes and hammer rivet pins in until it is flush with head. Refer to
Detail. NOTE: Distance from center rail of loop pole to arch should
be greater than 9".
4) Place hang glider rails onto crossover stubs. With glider rails in proper
position, drill through holes in hang glider rails into crossover with a
1/4" or "F" (only) drill bit. Insert 1/4" x 3/8" rivets into holes and ham-
mer rivet pins in until it is flush with head. Refer to Detail.
5) With curved loop pole steps and crossover level and rail hang glider
in proper position, pour concrete footings. Allow concrete footings
to cure for a minimum of 72 hours before users are allowed to play
on the structure.
6) Install protective surfacing before users are allowed to play on the
structure.
Eco #54543 Document 18496100 replaces 18282900. Changed curved loop pole part number.
