landscape structures Sheep Seesaw Guide

Freestanding Play
J:\SPECS\SPECS1\185\18578200.P65 Document #18578200
Seesaw Assembly 2
Replace if welds are broken, or if
the assembly is deformed, or se-
verely pitted with corrosion. Re-
pair damaged powdercoating per
instruction sheet.
Polyurethane Rod 1
ReplaceiftheSeesawpivotsfreely
and lacks resistance, the mecha-
nism binds, or metal-to-metal con-
tact is noted.
Sheep Seesaw
Seesaw
Assembly
Base
Assembly
DETAIL
LEG ATTACHMENT
Base Assembly
156257-00
Base Assembly 2
Replace if welds are broken, or if
the assembly is deformed, or se-
verelypitted with corrosion. Repair
damaged powdercoating per in-
struction sheet.
Leg 2
Replace if welds are broken, or if
theassemblyis deformed, or orse-
verely pitted with corrosion pitted
with corrosion.
(4) 1/2" x 1 1/4" Hex
Cap Screws
100216-00
Leg
148881-00
(4) 1/2" Standard
Hex Nuts
129692-00
© 2012 by Landscape Structures.
(4) 1/2" Flat
Washers
100363-00
(4) 1/2" Flat
Washers
100363-00
Bolt Covers/Permalene 1
Replace if plastic is cracked,
embrittled or seriously discolored.
Permalene
Surfacing 1
Surfacing should cover the base
of the seesaw with a 2"- 4"depth
and be level throughout the area.
(Please see Leg Attachment De-
tail) Warning: The seesaw de-
pends on correct surface height to
stop excessive movement. Ne-
glecting surfacing will lead to pre-
mature rubber failure.
2"-4"
Surfacing
Sheet 1 of 2
NOTE: Surfacing must
be maintained between
2"-4" above the bottom
of the base.
Fasteners 1
Tighten attachment fasteners. Re-
place if cracked, deformed or bro-
ken.
General Materials/Finishes1
Refer to the General Cleaning/Re-
pairing Instructions found in the
"Freestanding Play System Play-
ground Maintenance Sheet."
Bushings 1
Replace if mechanism binds or
metal-to-metal contact is noted.
Handles
Footrests
Handles/Footrests 1
Replace if cracked, deformed, or
broken. Repair damaged
powdercoating per repair sheet.

Sheep Seesaw
Seesaw reassembly
Should the need arise to reassemble the seesaw please complete
the following steps:
1. It is easiest to tape the 4 polyurethane rods to the square bar in the base,
as shown in the diagram. A single strip of 1" masking tape (not pro-
vided) wrapped around the middle of the polyurethane rods should suf-
fice. Press the rods between the half clamp gussets, both top and bottom.
Install 2 bushings on the top base bearing face with the thrust surface
facing the side plates.
2. With assistance, place the seesaw weldment on the base/polyurethane/
bushing assembly.Thehalfclamp onthe seesaw willstraddle the topset of
polyurethanerods and drop down on the bushings. Warning:Be careful
not to pinch your fingers in the assembly. The seesaw assembly will
need to be supported by a second person.
3. Install bushings in ends of lower half clamp. Lift the lower half clamp
into place so that it straddles the lower polyurethane rods. Have a sec-
ond person hold the lower clamp in place and balance the upper assem-
bly. Make sure both half clamps are centered between the sides of the
BaseAssembly.
4. Insert (4) 3/8" x 1 1/2" hex head fine thread bolts through the center holes
on the 4 corners of the half clamps. Use (8) 3/8" SAE flat washers on
both sides of the half clamp assembly, as shown in the diagram. It is
helpful to lightly lubricate the bolts with any available oil or grease (not
provided). Thread the 3/8" fine thread hex nuts onto the bolts and snug
each corner.
5. Evenly tighten the bolts in each corner until the half clamps are drawn
completely together. By tightening the bolts only a few turns each be-
fore going on to the next bolt, it is possible to keep the half clamp sur-
faces parallel to each other. Do not tighten a single bolt faster than the
others as the half clamps will skew at an angle and not mate together
correctly.
6. When the half clamps are just about to touch each other (1/32"-1/16" clear-
ance all around) place the (8) 3/8" tee nuts into the remaining holes of the
clamp assembly. Refer to the Base Assembly Detail on the next page.
The 3/8" tee nuts should drop all the way through the upper clamp holes
into the lower clamp holes. If the 3/8" tee nuts can not be pressed into
place, insert a punch or screwdriver through a clamp hole and pry on the
clamps until the holes of the upper and lower clamps are aligned.
7. With the first (8) 3/8" tee nuts in place and aligned correctly in the holes,
finish tightening the fine thread bolts. The half clamps should now be
touching. Install (through the bottom half clamp holes) (8) 3/8" x 7/8"
BHCS w/Pin and (8) D-Cut Flat washers. Tighten the bolts to 20 ft. lbs.
torque. Make sure the 3/8" tee nuts are seated against the half clamp.
There should be no space between the head of the 3/8" tee nuts and the
half clamp. If the 3/8" tee nut is not seated, loosen it and retighten in a
slightly different orientation until it seats.
8. Install (8) 3/8" jam nuts on the thread protruding out of the 3/8" tee nuts.
9. Remove and discard the fine thread hardware and washers.
10. Install the (4) Bolt Covers and 9/16" spacers with a 3/8" x 1 3/8" BHCS w/
Pin. Refer to the BaseAssembly Detail on the next page. In this case the
3/8" tee nuts come up through the bottom half clamp holes.
11. Install (4) 3/8" jam nuts on the thread protruding out of the lower half
clamp 3/8" tee nuts.
12. Re-Install the seesaw assembly per the seesaw installation instructions.
(4) 3/8" x 1 1/2"
Hex Head Fine
Thread Bolts
w/ 3/8" SAE Flat
Washers
(4) 3/8" x 1 1/2"
Hex Head Fine
Thread Bolts
w/ 3/8" SAE Flat
Washers
(4) Polyurethane
Rods
Seesaw
Torsion Half
Clamp
(4) 3/8" Fine
Thread Hex
Nuts w/ 3/8"
SAE Flat
Washers
(4) 3/8" Fine
Thread Hex
Nuts w/ 3/8"
SAE Flat
Washers
Tape
2 3/4" - 3"
Outside
Of Rods
Base
Assembly
Shown
Sectioned
(4) Polyurethane
Rods
Base Assembly
Shown Sectioned
For Clarity
(4) Seesaw
Bushings
Thrust
Surface
Top Base
Bearing
Face

Sheep Seesaw
DETAIL
BASEASSEMBLY
Freestanding Play
Document #18578200
Sheet 2 of 2
© 2012 by Landscape Structures.
Seesaw
(4) 3/8" x 1 3/8"
BHCS w/Pin
113027-00
(4) Bolt Covers
156370-00
(8) 3/8" Hex Jam Nuts
128296-00
(8) 3/8" Tee Nuts
100351-00
(4) Polyurethane
Rods
181001-00
Torsion Half Clamp
149173-00
(8) D-Cut Flat Washers
149272-00
(8) 3/8" x 7/8"
BHCS w/Pin
100196-00
(4) 3/8" Hex Jam Nuts
128296-00
(4) 3/8" Tee Nuts
100351-00
Base Assembly
156257-00
Shown Sectioned
For Clarity
(4) 9/16" O.D.
Spacers
185471-00
(4) Seesaw
Bushings
154164-00
Thrust
Surface
Top Base
Bearing
Face