Larson Atkins X-51 V4 User manual

IMPORTANT:
RETAIN FOR FUTURE REFERENCE,
READ CAREFULLY BEFORE USE
X-51 V4
RANGE CAMERA

SAFETY PRECAUTIONS
Read all instructions before operation and use of this range camera.
Keep instructions for future use.
This product complies with the applicable standard/s
at the specied compliance level (refer to Division
3.3 and 3.4 of the RLN) of the ACMA of Australia.
This product complies with all Australian radio
communications laws.
Larson Atkins Systems Pty Ltd is registered on the
national database of the ACMA.
TO AVOID POSSIBLE FAILURE OF TRANSMITTER, NEVER DISMANTLE THE
UNIT. THIS WILL ALSO VOID WARRANTY.
WEATHER RESISTANT DESIGN (WILL SURVIVE A LITTLE DRIZZLE BUT
WATER DAMAGE IS NOT COVERED UNDER WARRANTY AS A RESULT OF
IMPROPER USE OR SUBMERSION IN WATER).
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN
PERMANENT DAMAGE TO PRODUCT.
WARNING

CONGRATULATIONS
Congratulations on your purchase of the X51 V4 Range
Camera.
This product has been designed and developed with safety,
comfort and functionality in mind. Please take the time to
read this manual carefully before using this product and
keep it in a safe place for future reference.
Contents
Product Contents
Operating Instructions
Contact Details and Customer Service
Due to variations in the model and design of our products, the photographs shown in this instruction
manual are generic, therefore product nish, colour and design may vary from images shown. Larson
Atkins Systems reserves the right to alter product specications without notice as a result of our ongoing
policy of product development and improvement.

PRODUCT CONTENTS
Check what you have received
You have received 1 box. Please check the contents of the box against
the list below. If anything is missing, please contact Customer Service.
Supplied in box
Required for Operation (Not Supplied)
Receiver Unit
Includes contents:
• Wi-Fi Bridge
• Router
• Battery Pack
Compatible
Smart Device
• Android
• Apple
Charging Unit
Transmitter /
Camera Unit
Includes contents:
• Wi-Fi Bridge
• Camera
• Battery Pack
Charging
Cable
CamHi App
(Free)
Download from the
App Store on Smart
Device
x 1
x 1
x 1
x 1

OPERATING INSTRUCTIONS
At Home
1Remove Receiver Unit and Transmitter /
Camera Unit from box.
3When the charger is
plugged into the units, the
LED will illuminate in red.
When the battery is fully
charged, the LED will
illuminate in green.
4Download the CamHi App from the Apple/
Android store. (free App)
2Charge both the Receiver Unit and
Transmitter / Camera Unit overnight before
use.
PLEASE NOTE: Only one Charging Unit and Cable are
supplied in package. If you require a second Charging Set
you can purchase from www.larsonatkins.com

OPERATING INSTRUCTIONS
At Range
1Set up the Transmitter Unit approximately 5m from the target on
a 45 degree angle, and align antenna to point in the direction
of where you will be shooting from: Refer to diagram.
Transmitter Unit
(5m from target)
Receiver Unit
(with shooter)
5m
4
5
d
e
g
r
e
e
a
n
g
l
e

OPERATING INSTRUCTIONS
At Range
3Proceed back to the shooting position.
4At shooting position, set up Receiver Unit with
antenna facing the transmitter/camera unit.
Refer to diagram on previous page.
2Turn transmitter to the “On” position (The
camera will now turn on and boot up).
When rst turned on, one light will illuminate
to show the camera is doing a “limit
movement” test.
(This may take up to 1 minute, refer to picture)
Once all lights are illuminated, the camera is
ready.
ON
OFF

OPERATING INSTRUCTIONS
At Range
7Go to your Wi-Fi settings and connect to the
“LARSON ATKINS” Wi-Fi network.
PLEASE NOTE: This app does not use cellular data
5Turn switch to the “On” position by icking
down. This may take up to 1 minute to
connect to Transmitter/Camera Unit.
ON
OFF
61 red bar - Receives, but near the
extent of the range.
2 red bars - Receives, but not full
strength.
1 green bar - good signal.
2 green bars - full signal.
Once you have red or green bars, you are
ready to connect you phone to the App.

1Open the CamHi App on your Smart Device.
OPERATING INSTRUCTIONS
To operate CamHi App
3Select “Search camera from LAN” and select
camera.
Select the tick icon in top right corner to
action.
Your camera will now be “Online”.
4Select synced camera in list.
Set up is now complete, congratulations you
are now ready to shoot.
2Select the “Add Camera” button.

OPERATING INSTRUCTIONS
CamHi App Icons
Mirror and Flip Image Mute Sound
Zoom In / Out Take Snapshot
Reception Record Video
Power to App HD Option