LawnMaster MEH1533M User manual

Instruction Manual
33cm 1500W Hover Mower MEH1533M
Read all safety instructions carefully before assembling and operating
this machine. Ensure the machine has been assembled correctly and safely. Keep the
instructions safe and pass them on to any subsequent user so that the information is always
available.
WARNING:
Original Instructions

1
2
3
4
5
6
7
8
10
11
12
13
14
15
16
17
9
19
18

5
TABLE OF CONTENTS
Section Page
Symbols
Safety Information
In the Box
Assembly
Operation
Maintenance
Troubleshooting
Technical Data
Recycling and Disposal
6-7
8-16
16
17
18-20
21-22
23-24
25
25

6
The following warning symbols appear throughout this manual and indicate the
appropriate safety measures you should take when operating and maintaining the
appliance.
SYMBOL DESIGNATION/EXPLANATION
Caution
Read instruction manual.
Keep bystanders away.
Beware of sharp blades. Blades may continue to rotate after the motor is
switched off. Beware of injury to toes or ngers.
Switch off the motor and disconnect the plug before carrying out maintenance or
repair work or if the power cable is caught or damaged.
Wear eye and ear protection.
Do not expose to rain.
Wait until all moving parts have stopped completely before touching them. The
blade may continue to rotate after the machine is switched off, a rotating blade
can cause injury.
WARNING! Beware of electric shocks.
Keep the power cable away from the cutting blade!
Cutting circle
Protection class II (Double insulation)
Noise level specication LWA in dB.
Electrical appliances must not be disposed of with the domestic waste.
SYMBOLS
33cm

7
SYMBOLS
To avoid serious personal injury, do not attempt to use this product until you read thoroughly and
understand completely the instruction manual.
If you do not understand the warnings and instructions in the instruction manual, do not use this
product.
WARNING

8
SAFETY INFORMATION
When using equipment, the following safety precautions
must be followed to avoid injuries and damage:
IMPORTANT
■ Read all operating instructions carefully and comply with
them. It is important to understand these instructions and to
acquaint yourself with the machine, its correct usage and
all safety requirements.
■ Keep this manual in a safe place so that the information is
available to the operator at all times.
■ If you give the equipment to any other person, give them
these operating instructions as well.
■ We accept no liability for damage or accidents which result
from non-compliance with these instructions.
The device must not be used by people (including children)
with limited physical, sensory or mental capabilities or who
lack the necessary experience and/or knowledge - other than
they are supervised by a person responsible for safety or are
being instructed to operate the appliance by such a person.
Children should be supervised to ensure that they do not play
with the appliance.
■ Read the instructions carefully. Be familiar with the controls
and the correct use of the lawn mower.
■ Never allow children or people unfamiliar with these
instructions to use the mower. Local regulations may
restrict the age of the operator.
■ Never operate the machine while people, especially

9
SAFETY INFORMATION
children, or pets are nearby.
■ Keep in mind that the operator or user is responsible for
accidents or hazards occurring to other people or their
property.
■ While operating the mower always wear substantial
footwear and long trousers. Do not operate the mower
when barefoot or wearing open toed sandals. Avoid
wearing clothing that is loose tting or that has hanging
cords or ties.
■ Thoroughly inspect the area where the mower is to be
used. Remove all stones, sticks, and other objects that could
be tripped over or thrown by the blade. Thrown objects can
cause serious personal injury.
■ Before using, always visually inspect to see that the
blade, blade bolt and the blade assembly are not worn or
damaged. Replace worn or damaged components in sets
to preserve balance. Replace damaged or unreadable
labels.
■ Before use check the power supply and extension
cord for signs of damage or aging. If the cord becomes
damaged during use, disconnect the cord from the supply
immediately. DO NOT TOUCH THE CORD BEFORE
DISCONNECTING THE SUPPLY. Do not use the machine
if the cord is damaged or worn.
■ Operate the mower only in daylight or in good articial light.
■ Do not use the lawn mower in damp or wet conditions or
operate in the rain.
■ Working on sloping areas can be dangerous. Do not mow
on excessively steep slopes. Always be sure of your footing
on slopes or wet grass.

10
SAFETY INFORMATION
■ Walk, never run.
■ Switch off the motor and disconnect the plug before
carrying out any inspection, servicing or maintenance work.
■ Ensure that all the guards are securely tted and in good
working order.
■ Mow across the face of slopes, never up and down.
■ Exercise extreme caution when changing direction on
slopes.
■ Use extreme caution when reversing or pulling the mower
towards you.
■ Stay Alert: Do not operate the mower when you are tired.
Pay attention to what you are doing.
■ Do not operate the mower while under the inuence of
alcohol or drugs.
■ Stop the blade(s) if the machine has to be tilted for
transportation when crossing surfaces other than grass,
and when transporting the machine to and from areas to be
mowed.
■ Switch on the motor carefully according to instructions and
with feet well away from the blade(s).
■ Do not tilt the machine when starting or switching the
motor on, except if the machine must be tilted for starting
in long grass. In this case, do not tilt it more than absolutely
necessary and tilt only the part which is furthest away
from the operator. Always ensure that both hands are in
the operating position on the handle before returning the
machine to the ground.
■ Do not start the machine when standing in front of the
discharge opening.
■ Do not put hands or feet near or under rotating parts. Keep

11
SAFETY INFORMATION
clear of the discharge opening at all times.
■ Never pick up or carry the machine while the motor is
running.
■ Do not overreach. Keep proper footing and balance at all
times.
■ Do not use a machine if the switch does not turn it on and
off. Any machine that cannot be controlled with the switch
is dangerous and must be repaired.
■ In case any of the following situations occur, stop the
mower and remove plug from the socket. Make sure that all
moving parts have come to a complete stop:
− Whenever you leave the mower,
− Before clearing blockages,
− Before checking, cleaning or working on the mower,
− After striking a foreign object. Inspect the mower for
damage and make repairs before restarting and operating
the mower.
■ If the mower starts to vibrate abnormally (check
immediately)
− Inspect for damage,
− Replace or repair any damaged parts,
− Check for and tighten any loose parts.
■ Keep all nuts, bolts and screws tight to be sure that the
mower is in a safe condition for use.
■ Be careful during adjustment of the mower to prevent
entrapment of the ngers between moving blade and xed
parts of the machine.
■ Always allow the mower to cool down before storing.
■ When servicing the blade be aware that, even though the
power source is switched off, the blade can still be moved.

12
SAFETY INFORMATION
■ Replace worn or damaged parts for safety. Use only
genuine replacement parts and accessories.
■ Always be alert when using the machine, so that you can
recognise and handle risks early. Fast intervention can
prevent serious injury and damage to property.
■ Switch off and remove the power cord from the plug if there
is any malfunction. If necessary have the machine checked
by a qualied specialist and repaired before you operate it
again.
■ WARNING! Even if you are operating the machine in
accordance with all safety requirements, potential risks of
injury and damage remain. The following dangers can arise
in connection with the structure and design of this machine:
- Health defects resulting from vibration emission if the
machine is being used over long periods of time or not
adequately managed and properly maintained.
- Injuries and damage to property due to broken application
tools or sudden impact of hidden objects during use.
■ WARNING! This machine produces an electromagnetic
eld during operation! This eld may under some
circumstances interfere with active or passive medical
implants! To reduce the risk of serious or fatal injury, we
recommend persons with medical implants to consult their
doctor and medical implant manufacturer before operating
this product!
■ The machine should be supplied via a residual current
device (RCD) with a tripping current of not more than
30 mA.
■ Ensure that the mains voltage matches the specications
on the rating plate.

13
SAFETY INFORMATION
■ Use only authorised power cables of type H05VV-F, which
are no more than 75 m long and suitable for outdoor use.
The power cable wire cross section must be at least 2.5
mm2. Always completely unroll cable drums before use.
Check the cable for damage.
■ Keep the power cable away from the cutting tool when
working. The cutting blades may damage the power cable
and result in contact with live parts. Always run the power
cable behind the operator. The extension cable can be
accidentally cut. Risk of electric shock!
■ Do not use the power cable to pull the plug from the socket.
Protect the power cable from heat, oil and sharp edges.
■ Switch off the equipment and disconnect the plug from the
socket if the power cable is damaged. If the power cable
is damaged, it must be replaced by the manufacturer, the
customer services of the same, or a qualied person, in
order to avoid hazards.
■ Do not connect a damaged power cable to the mains. Do
not touch a damaged power cable when it is connected to
the mains. A damaged power cable may result in contact
with live parts.
■ Do not attempt to repair the equipment yourself unless you
have been trained to do so. Any work not specied in these
instructions is to be carried out only by a qualied person.
■ Use only spare parts and accessories supplied and
recommended by the manufacturer. The use of non-original
parts will immediately invalidate the guarantee.
■ Do not overload the equipment. Work only within the
specied power range and do not change the regulator
settings on the motor. Do not use low-powered machines

14
SAFETY INFORMATION
for heavy work. Do not use your equipment for purposes
other than those for which it is designed.
■ Do not lift or carry the equipment when the motor is
running. Risk of injury from cuts.
■ Do not use the equipment near inammable liquids or
gases. Non-observance will result in a risk of re or
explosion.
■ Keep the equipment in a dry location and out of reach of
children.
■ Remove cut material only when the equipment is stopped
and disconnected from power supply.
■ Do not leave the equipment unattended in the workplace.
■ Handle the equipment with care. Keep tools sharp and
clean, in order to facilitate better and safer work. Follow the
maintenance instructions.
Double Insulation
■ Double insulation is a concept in safety in electric power
tools, which eliminates the need for the usual three-wire
grounded power cord.
■ All exposed metal parts are isolated from the internal
metal motor components with protecting insulation. Double
insulated tools do not need to be grounded.
■ WARNING! The double insulated system is intended
to protect the user from shock resulting from a break in
the tool’s internal insulation. Observe all normal safety
precautions to avoid electrical shock.
■ NOTE: Servicing of a product with double insulation
requires extreme care and knowledge of the system and
should be performed only by a qualied technician.

15
SAFETY INFORMATION
Electrical Connection
■ This product has a precision-built electric motor. It should
be connected to a power supply that is 220-240V~50 Hz,
AC only (normal household current). Do not operate this
product on direct current (DC). A substantial voltage drop
will cause a loss of power and the motor will overheat. If
the product does not operate when plugged into an outlet,
double-check the power supply.
Extension Cords
■ When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the product will draw. An
undersized cord will cause a drop in line voltage, resulting
in overheating and loss of power.
■ Before you connect the mower to the mains supply make
sure that data on the rating plate are identical to the mains
data. Before using any extension cord, inspect it for loose
or exposed wires and cut or worn insulation.
■ WARNING! Keep the extension cord clear of the working
area. Position the cord so that it will not get caught on
obstructions while you are working with a power tool.
Failure to do so can result in serious personal injury.

16
SAFETY INFORMATION
Intended Use
This lawnmower is designed for domestic use only:
■ This electric lawnmower is intended for mowing lawns in
domestic and hobby gardens.
■ This product is not to be used in wet weather conditions
and may not be used to mow wet or unusually high grass.
■ This product is intended for private domestic use only,
not for any commercial trade use. It must not be used for
any purposes other than those described. Any use of the
machine that deviates from its intended use will invalidate
the warranty.
IN THE BOX
1. Safety Switch Button
2. Cable Strain Relief
3. Upper Handle
4. Wing Nut (x4)
5. Washer for Upper Handle (x2)
6. Middle Handle (x2)
7. Washer for Middle Handle (x2)
8. Lower Handle
9. Screw (x2)
10. Deck
11. Wheel
12. Carry Handle
13. Spacer (x3, one pre-tted)
14. Spanner
15. Cable Clip (x3)
16. Switch Lever
17. Switch Box
18. Blade
19. Blade Bolt

17
ASSEMBLY
Assembly Preparation
■ Carefully remove all contents from the product packaging.
■ Ensure you have all the accessories and tool(s) needed for assembly and operation. This also
includes suitable personal protective equipment.
Assembling the Lower Handle (See Figs. 1-2)
■ Insert the lower handle into the slots on the deck (Fig. 1).
■ Fix the lower handle using the enclosed screws (Fig. 2).
Assembling the Middle Handles (See Fig. 3)
■ Fit the middle handles and lower handles together with the wing nuts and washers for middle
handle on both sides of the handle assembly. Ensure the bolts and wing nuts are assembled
in the correct method. Failure to assemble the wing nuts correctly can result in damage to the
product (Fig. 3).
Assembling the Upper Handle (See Figs. 4-5)
■ Fit the upper handle and lower handle together with the wing nuts and washers for middle
handle on both sides of the handle assembly. Ensure the bolts and wing nuts are assembled
in the correct method. Failure to assemble the wing nuts correctly can result in damage to the
product (Fig. 4).
■ Secure the cable against the handle frame with the supplied cable clips. Ensure the cable is
clipped into the cable clips (Fig. 5).
If any parts are damaged or missing do not operate this product until the parts are replaced.
Failure to pay attention to this warning could result in serious personal injury.
Do not attempt to modify this product or create accessories not recommended for use with this
product. Any such alteration or modication is misuse and could result in a hazardous condition
leading to possible serious personal injury.
Never operate the mower without the proper safety devices in place and in working order. Never
operate the mower with damaged safety devices. Failure to pay attention to this warning can result
in serious personal injury. Make sure all packing is removed from product parts before starting
assembly.
WARNING
WARNING
WARNING

18
OPERATION
Adjusting the Cutting Height (See Fig. 6)
Switch off the equipment, disconnect the plug from the power supply and wait for the blade to
come to a complete stop before adjusting the cutting height. A rotating blade can cause injury.
WARNING
Before using the mower for the rst time, adjust the cutting position to the height best suited for
your lawn.
The mower comes with one spacer pre-tted and can be set to 4 cutting heights between 12mm
and 33mm. Choose the appropriate cutting height according to the types and conditions of the
grass.
To set the cutting height:
■ Stop the motor and allow the blade to come to a complete stop.
■ Slowly turn the mower onto its side. Wedge a block of wood between the blade and the mower
deck, or use safety gloves to rmly hold the blade to prevent the blade from turning.
■ Remove the blade bolt using the spanner provided.
■ Remove the washer and the blade.
■ To raise the cutting height, remove the required amount of spacers. To lower the cutting height,
add the required amount of spacers (Fig. 6).
■ Ret the blade as described in Blade Maintenance.
■ Spacers that are not being used can be stored on the spanner to prevent loss.
Do not allow familiarity with this type of product to make you careless. Always pay attention when
operating this product, not doing so can result in serious injury.
Always wear safety goggles or safety glasses with side shields when operating this product.
Failure to do so could result in objects being thrown into your eyes, resulting in possible serious
injury.
WARNING
WARNING
CUTTING POSITION CUTTING HEIGHT
1 (Non-spacer) 33mm
2 (1 Spacer, pre-assembled) 26mm
3 (2 Spacers) 19mm
4 (3 Spacers) 12mm

19
OPERATION
The blade may keep rotating for a few seconds after the device has been switched off. Do not
touch the rotating blade. A rotating blade can cause injury.
WARNING
■ Hook the mains cable through the cable strain-relief (Fig. 7).
■ Connect the mower to your power supply.
■ Before switching the mower on, make sure that the working area is free from debris and foreign
objects.
■ To switch on, press and hold the safety switch button and gently pull the switch lever towards
the upper handle. Once started, release the safety switch button (Fig. 8).
■ To power off the mower, release the switch lever.
General Operation
Check the product and accessories for damage before each use. If damage is present or observed,
please stop and have mower serviced before use. Do not use the product if it is damaged.
■ Double check that the blade is properly installed.
■ Always hold the product by its handles. Keep the handle dry to ensure safe support.
■ Ensure that the air vents are always unobstructed and clear. Clean them if necessary with a soft
brush. Blocked air vents may lead to overheating and damage the product.
■ Switch the product off immediately if you are disturbed while working by other people entering
the working area.
■ Do not overwork yourself. Take regular breaks to ensure you can concentrate on the work and
have full control over the product.
Mowing Advice (See Fig. 9)
■ Avoid cutting the power cable. It is advised to mow away from the plug socket and avoid twisting
the power cord. Mow at a normal walking pace and always overlap tracks by a few centimetres
for a gap-free nish.
■ Make sure the lawn is clear of stones, sticks, wires, and other objects that could damage the
lawn mower blades or motor. Such objects could be accidentally thrown by the mower in any
direction and cause serious personal injury to the operator and others.
Starting/Stopping the Mower (See Figs. 7-8)
■ For the rst cut each season, a higher cutting setting should be selected. It is recommended to
cut longer grass in 2 passes or more. This method will also cause less stress to your grass for a
healthier lawn.
■ Before you begin to mow, check to ensure that the blade is not blunt and that none of the
fasteners are damaged. To prevent any imbalance, replace blunt and/or damaged blades. To
carry out this check, rst switch off the motor and remove the plug from the power supply.

20
OPERATION
■ When cutting longer grass, cut the grass in two or more passes by lowering the cutting height
gradually at each pass. Never cut the grass by more than half its height.
■ When cutting dense grass, reduce walking speed to allow for more effective cutting and a
proper collection of the clippings.
■ Do not cut wet grass as it can stick to the lawn mower and prevent the proper discharge of
grass clippings.
■ Clean the underside of the mower deck after each use to remove grass clippings, leaves, dirt,
and any other accumulated debris.
■ Watch for holes, ruts, rocks, hidden objects, or bumps which can cause you to slip or trip. Tall
grass can hide obstacles. Remove all objects such as rocks, tree limbs, etc., which could be
tripped over or thrown by the blade.
■ Always be sure of your footing. A slip and fall can cause serious personal injury. If you feel you
are losing your balance, release the start/stop switch lever immediately.
■ Slopes are a major factor related to slip and fall accidents that can result in severe injury.
Mowing on slopes requires extra caution. If you feel uneasy on a slope, do not mow it. For your
safety, do not attempt to mow slopes greater than 15 degrees.
■ Do not mow near drop-offs, ditches, or embankments; you could lose your footing or balance.
■ We recommend that you mow in overlapping lines for effective grass collection. This will keep
the rows even and ensures that all the lawn is cut without missing any spots (Fig. 9).