LED Linear Xootube IP40 User manual

PENDANT FALSE CEILING
INSTALLATION INSTRUCTIONS
XOOTUBE IP40
LED Linear™GmbH
Pascalstraße 9
47506 Neukirchen-Vluyn
Germany
Phone [phone]
Fax [phone]
[e-mail]
ENGINEERED IN GERMANY
Art. # 33100019
Attention: Do not touch LEDs. Fragile!
Electrostatic discharges can damage the LEDs.
Ø 12
Supplied accessories
Supplied accessories
Required tools
Required tools
General Safety Instructions
•Read the instructions for installation and commissioning.
•Pass the instructions to the customer for safekeeping.
•Do not remove the factory label of the luminaire.
•Please note the national installation and accident prevention regulations
during installation.
The installation must be performed only by a trained electrical specialist.
•Damaged cables may only be changed by trained electrical personnel.
•For improper installation or any subsequent change to the luminaire no
liability is accepted.
•The light source of this lamp may be replaced only by the manufacturer or
an authorized service technician or a similarly qualified person.
•LED lamps (without IP67 protection) must not be cleaned.
•Clean the luminaire regularly with a smooth damp cloth. Only use
solvent-free cleaning agents. Attention: previously cut off the mains supply
and allow system to cool down.
•To protect the surface from dirt and fingerprints, we recommend the use
of protective gloves during installation.
•The disposal of the system must be carried out on the disposal of
electronic products in accordance with the EU Directive WEEE (Waste
Electronical and Electronic Equipment).
•In order to answer technical queries, please contact our project
management respectively our worldwide branches and distributors.
Please send your request to [e-mail].
Mains voltage / connection
•Check that there is no voltage of the system prior to installation and
maintenance. Beware of electric shock!
•Only use converters of the correct voltage.
•It is not allowed to use the luminaires with altered or damaged connector
cables.
•In case of a three-phase installation do not interrupt the neutral conductor
of the electronic ballasts.
•Electrically operated (Constant Current) LED modules must not be
secondary side connected.
•Avoid overvoltage at the electronic control gear.
•The cable must not cover the light-emitting portion.
•Connecting and disconnecting the luminaire and the control gear under
present voltage can cause damage to the components.
•Mismatched luminaires and control gears can damage each other.
•Wrongly polarized cables damage the luminaire.
•The installation of a Dali system may only be performed by trained
personnel. Pay attention to any necessary mains voltage resistance of the
Dali operating device.
•Only suitable dimmers must be used for dimming. Observe the manufacturer‘s
instructions. Not suitable dimmers can damage the whole system.
•Terminals in accordance with EN 60998-2-1 or EN 60998-2-2 must be used
for connecting the lamp to the power grid.
Environment
•Pay attention to the allowable ambient conditions under which the luminaire
may be operated.
•Install the luminaire in a place where it is not exposed to direct sunlight or
heat sources.
•Ensure that the recessed version is not covered with insulating material.
•Do not cover luminaire and control gear to prevent overheating.
•Pay attention to the minimum distance between luminaire and lighted
object.
•Be careful with allowable floor loads in case of ceiling mounting of the
luminaire.
•Exterior lighting should be used only after sunset until sunrise.
VERTICAL PENDANT
© LED Linear GmbH / All rights reserved, subject to change / Technical amendments and graphical presentation are subject to change. Edition 01/2018

X
+ 0,3”
+ 7,5 mm
+ 0,3”
+ 7,5 mm
Ø 12
X
1.2
ABAC
B
3.6–3.11
1.1
VERTICAL PENDANT 2.1–2.4 | 3.1–3.11PENDANT FALSE CEILING 1.1–1.6
24V
24V
IQ WHITE DC:
WHITE
RED
GREEN W822/W825
BLUE W840
RGB 24V DC:
WHITE
RED
GREEN
BLUE
WHITE 24V DC:
RED
BLACK
© LED Linear GmbH / All rights reserved, subject to change / Technical amendments and graphical presentation are subject to change. Edition 01/2018

OK
OK
2.6
1.3
2.42.3
2.2
1.4
2.1
1.5 1.6
© LED Linear GmbH / All rights reserved, subject to change / Technical amendments and graphical presentation are subject to change. Edition 01/2018

OK
Ø 12
2.7
3.1 3.2
3.1
3.3 3.4
3.6 3.7
3.5
L = approx. 1,9“
L = 50 mm
L = approx. 1,9“
L = 50 mm
© LED Linear GmbH / All rights reserved, subject to change / Technical amendments and graphical presentation are subject to change. Edition 01/2018

OK
3.8 3.9
3.10 3.11
© LED Linear GmbH / All rights reserved, subject to change / Technical amendments and graphical presentation are subject to change. Edition 01/2018