Ledon Tube Slides User manual

1
Ledon Tube Slides
Assembly instruction

2
Hints and Tips ................................................................... 3
Installation example ............................................................... 4
Tunnel Maker assembly instructions .................................................. 5
Startpanel ....................................................................... 6
Useful information about LEDON tubes .............................................. 7
Installation of the first tube ......................................................... 9
Installation of tubes ............................................................... 10
Installation of tubes with windows ................................................... 11
Installation of tubes - finishing ....................................................... 12
Exit chute ....................................................................... 13
Exit chute - installation of anchoring .................................................. 16
Exit chute - installation of concrete bracket ............................................ 18
Trenching of the ground anchor ..................................................... 19
Finish........................................................................... 21
Contents

3
1. Remove the components from the pallet and place them on the ground
2. Check the following list of components and ensure you have them all
3. Unwrap one component at a time and try to finish with that component immediately
4. Use your spirit level carefully
5. Safety surfacing is established at the very end when attaching the label from the producer
Tips:
Slides with a starting height below 2 meters can be mounted on the ground and then lifted up.
Slides with a start height over 2 meters can be mounted in sections on the ground.
We try to make our assembly instructions as useful as possible.
Do you have any advice or tips for us, we hope to hear from you.
Please write to [email protected] or via the contact form on our website www.ledonplay.com
Hints and Tips

4
Here we will go through the assembly instructions by an example of the beautiful, curved and colorful
LEDON tunnel slide below.
Each tunnel is unique and must be assembled according to the LEDON Tunnel Maker installation
instructions. If a support post is necessary see separate assembly instructions for this.
Always remember to follow the LEDON assembly instructions.
Installation example

5
Filename:
Printed:
Ledontubeslidestart366cm
11/7/2014at10:27
Version: TunnelMakerv2r12
Startheight:
Dimensions:
366.0cm
182x326cm
FRONT RIGHT
TOP AXO
Mountingguide:
A A
35cm
12 12
38°
A A
35cm
A A
106cm
17 12
45°
912
45°
14 12
32°
612
45°
13 12
38°
812
38°
12 12
32°
10 5
32°
A A
35cm
A A
59cm
24 24
38°
A
End
Start
A Tunnel Maker assembly instruction from LEDON is useful when setting up
the tunnel slide. In the following example we will show you how.
Example of a Tunnel Maker assembly instruction:
Tunnel Maker assembly instructions

6
Starting
All tube assembly starts with the startpanel. Attach fiber and bolts as shown below.
Startpanel

7
A
Straight tubes: All straight tubes are marked with the letter ”A” at each end of the tube.
This letter refers to the Tunnel Maker mounting instruction supplied by LEDON.
The ”A” should always be in the ”top” of the tube.
Example of assembly instructions:
Useful information about LEDON tubes

8
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Useful information about LEDON tubes
Curved tubes: All curved tubes are numbered 1-24 next to each flange hole.
These numbers refer to the Tunnel Maker mounting instruction supplied by LEDON - see below
Example of assembly instructions:

9
A
Apply the first tube so that ”A” is in the ”top” of the tube.
Installation of the rst tube

10
The tubes are installed in the sequence and aligning numbers with letters as shown in the
LEDON Tunnel Maker assembly instructions.
Installation of tubes

11
When LEDON’s assembly instructions are followed, it is ensured that the windows are not on the
sliding surface.
Windows must sit on at ”10” and ”2” o’clock position.
Installation of tubes with windows

12 Installation of tubes - nishing
Important: Install the second last tube and the exit chute together in a section before it is applied on
the tube slide.

13
A
Important: Install the second last tube and exit chute together in a section before it is loaded onto the
slide.
Exit chute
5 pcs. 10x25 mm MB
(Installed in the bushes)
Bolts must not be overtightened!
11 pcs. 10 x 40 mm MB + 11 x 10,5 x 30 mm SEK

14
5 pcs. 10x25 mm MB
(Installed in the bushes)
Bolts must not be overtightened!
Apply the second last tube so that ”24” is in the ”top” of the tube. As in this example.
Exit chute

15
Install the other bolts.
Exit chute
11 pcs.
10x45 mm MB

16
10 x 35 mm BB
Installation of anchoring - for trenching.
For mounting on concrete - see page 18.
Exit chute - instalation of anchoring

17
For the stability of the anchoring and the exit chute, a PE-plate must be mounted INSIDE the
exit chute and fastened, with metal bracket by 3 screws. See picture below.
Exit chute - installation of anchoring

18
1
2
3
Exit chute - installation of concrete bracket
Installation of anchoring for concrete.

19
50 cm
Trenching of the ground anchor
Dig out for the ground anchor only when the tunnel slide is fully assembled and standing on the
ground, not before. See drawing below.

20
1
2
3
4
NB
Trenching of the ground anchor