Lefroy Brooks C1-1110 User manual

INSTALLATION INSTRUCTIONS
C1-1110
CROSS HANDLE BASIN BRIDGE
MIXER WITH 6 ½” SPOUT
CW-1110
WHITE LEVER BASIN BRIDGE
MIXER WITH 6 ½” SPOUT
CB-1110
BLACK LEVER BASIN BRIDGE
MIXER WITH 6 ½” SPOUT
C1-1110 CB-1110
CW-1110

2
Dimensions in Inches (& Millimetres)
Whilst every effort is made to ensure accuracy, design and dimensions are subject to
change without notice as part of the company’s product development process.
C1-1110 (LB9007)
2-3/4-14NPSM-2A
6 1/2"
(165mm)
7 7/8"
(200mm)
10"
(253.73mm)
Ø3/4"
(Ø19mm)
Ø1"
(Ø25mm)
4 5/8"
(117.63mm)
R 3 5/8"
(R92mm)
10 5/16"
(261.36mm)
3/4"
(19.3mm)
Ø7/16"
(Ø11mm) Ø1 1/2"
(Ø38.3mm)
4 1/2"
(113.9mm)

3
Dimensions in Inches (& Millimetres)
Whilst every effort is made to ensure accuracy, design and dimensions are subject to
change without notice as part of the company’s product development process.
CW-1110 (WL9007)
2-3/4-14NPSM-2A
4 5/8"
(117.63mm)
6 1/2"
(165mm)
10"
(253.73mm)
14 1/2"
(368mm)
Ø3/4"
(Ø19mm)
Ø1"
(Ø25mm)
7 7/8"
(200mm)
R3 5/8"
(R92mm)
Ø7/16"
(Ø11mm)
Ø1 1/2"
(Ø38.3mm)
4 3/8"
(110.73mm)
3/4"
(19.3mm)

Dimensions in Inches (& Millimetres)
Whilst every effort is made to ensure accuracy, design and dimensions are subject to
change without notice as part of the company’s product development process.
CB-1110 (BL9007)
4
2-3/4-14NPSM-2A
7 7/8"
(200mm)
14 1/2"
(368mm)
Ø7/16"
(Ø11mm)
4 3/8"
(110.73mm)
Ø1 1/2"
(Ø38.3mm)
R3 5/8"
(R92mm)
Ø3/4"
(Ø19mm)
Ø1"
(Ø25mm)
3/4"
(19.3mm)
6 1/2"
(165mm)
4 5/8"
(117.54mm)
10"
(253.64mm)

5
Please note:
When there is a difference in water pressure between
hot and cold supplies to the mixing valve, the pressures
should by equalized by a plumber in accordance with
best practice and legislation.
What you need to know
Prior to beginning installation. turn off the cold and
hot water lines and open the old faucet to release
built-up pressure.
Overtightening nuts may cause damage.
Wrap all threaded connections with pipe tape
available at your local plumbing supply store.
Always wrap in a clockwise direction. The fittings
should be installed by a state-licenced plumber.
Adjustable Wrench
Groove Joint Pliers
Hacksaw
Phillips Screwdriver
Pipe Tape
Spatula
Spirit Level
Your new bathroom faucet is designed for years
of trouble-free performance.
Keep it looking new by cleaning it periodically with
a soft cloth. Avoid abrasive cleaners, wire wool and
harsh chemicals as these will dull the finish and
void your warranty.
If you are soldering during faucet installation,
remove cartridges, seats, gaskets and washers
prior to applying flame, otherwise you will void
the warranty.
Cover drain openings to avoid losing small parts.
When cutting or soldering pipe, use safety glasses
to protect your eyes.
Correct installation may vary depending on previous faucet installation. All necessary supplies required for
faucet installation are not included, but may be found where plumbing supplies are sold. It is suggested that
IAPMO and/or CSA approved plumbing supplies are used during installation.
Tools: Maintenance
Safety Tips
Things You May Need
Important Points
IAPMO/cUPC Listed
Meets NSF 61-9
Meets A112.18.1
Please note :
Final achievable flow rate is dependent on the outlets fitted, see relevant outlets (spouts, roses, sprays) for fully
assembled product flow rate.
Standards Flow Rate
0
1
2
20 40 60 80PSI

6
Steps 1-2
Installation Procedure
Lefroy Brooks always recommends that plumbing products be installed by a licensed professional.
Shut off main water supply before installation.
1Take out product from the box. Turn the
spout to the right front position as the
figure instructed. Tighten the fixing set
screw to secure the spout fixed.
2Install the faucet onto either the return bends
or the cranked legs as chosen. Attach the
legs to the faucet but do not screw the nut
up tightly yet.
1 2
90°

7
Steps 3-4
Installation Procedure
Lefroy Brooks always recommends that plumbing products be installed by a licensed professional.
Shut off main water supply before installation.
3Attach escutcheons to the legs, then install
the legs to the deck. 4After placing the legs in the right position, fix
the legs with nuts from underneath the deck.
Finally tighten the nuts between the legs and
the faucet to seal securely.
34

8
Steps 5
Installation Procedure
Lefroy Brooks always recommends that plumbing products be installed by a licensed professional.
Shut off main water supply before installation.
5After installing faucet, remove aerator and
open the hot and cold supplies. Check for
leaks. Turn on faucet handle for one minute
to flush debris from faucet. Turn off the
handle and re-assemble the aerator.
5

9
Exploded View
Parts List
C1-1110 (LB9007)
1 Ceramic indices (C) (129312C)
2 Handle (029721-T)
3 O-ring (048085N)
4 Canopy (018253)
5 Clip (012255)
6 Stem extension (110461)
7 Washer (013570)
8 Screw (008670)
9 Cartridge (507907W)
10 Screw (008252)
11 Clip (012112N)
12 O-ring (004005N)
13 Clip (012060)
14 Adaptor (018227)
15 O-ring (063066N)
16 Spout assembly (139863W)
17 Oil-seal (010519N)
18 Aerator insert (553661N)
19 Aerator housing (305849N-54)
20 Ceramic indices (H) (129312H)
21 Body (002678W)
22 Allen key (031000)
21
4
6
16
13
11
10
12
14
15
2
20
1
17
19
3
8
18
7
5
9
22

10
Exploded View
Parts List
CW-1110 (WL9007)
1 Handle-end cap (109376)
2 Handle stem (017094)
3 Handle sleeve (108924)
4 Adaptor (205144)
5 Ceramic indices (C) (129313C)
6 O-ring (048085N)
7 Canopy (018253)
8 Clip (012255)
9 Stem extention (110461)
10 Washer (013570)
11 Screw (008670)
12 Cartridge (C) (507176W)
13 Screw (008252)
14 Clip (012112N)
15 O-ring (004005N)
16 Clip (012060)
17 Adaptor (018227)
18 O-ring (063066N)
19 Aerator housing (305849N-54)
20 Spout assembly (139863W)
21 Oil-seal (010519N)
22 Aerator insert (553661N)
23 Ceramic indices (H) (129313H)
24 Cartridge (H) (507175W)
25 Body (002678W)
26 Allen key (031000)
1
2
3
4
5
6
7
9
13
14
15
16
20
21
23
25
17
18
19
22
11
8
10
24
1226