Lefroy Brooks X1-2010 User manual

INSTALLATION INSTRUCTIONS
X1-2010 (XO5400)
CROSS HANDLE THERMOSTATIC WITH ZU LEVER FLOW CONTROL TRIM ONLY,
TO SUIT M1-4201 ROUGH

2
Dimensions in Inches (& Millimetres)
Whilst every effort is made to ensure accuracy, design and dimensions are subject to
change without notice as part of the company’s product development process.
8 3/8"
5 11/16"
2 13/16"2 5/8"
1 5/8"
2 3/16"
1 1/16"
45°
7/8" 1 15/16"
3/16"
9/16"
1 7/16"~3 1/16"
(212.5mm)
(145mm)
(72mm)(67mm)
(42mm)
(55mm)
(27.5mm) (22.2mm) (49mm)
(4.5mm)
(15mm)
(37~78.5mm)

3
What you need to know
Adjustable Wrench
Groove Joint Pliers
Hacksaw
Phillips Screwdriver
Pipe Tape
Spatula
Spirit Level
Your new bathroom faucet is designed for years
of trouble-free performance.
Keep it looking new by cleaning it periodically with
a soft cloth. Avoid abrasive cleaners, wire wool and
harsh chemicals as these will dull the finish and
void your warranty.
If you are soldering during faucet installation,
remove cartridges, seats, gaskets and washers
prior to applying flame, otherwise you will void
the warranty.
Cover drain openings to avoid losing small parts.
When cutting or soldering pipe, use safety glasses
to protect your eyes.
Correct installation may vary depending on previous faucet installation. All necessary supplies required for
faucet installation are not included, but may be found where plumbing supplies are sold. It is suggested that
IAPMO and/or CSA approved plumbing supplies are used during installation.
Prior to beginning installation. turn off the cold and
hot water lines and open the old faucet to release
built-up pressure.
Overtightening nuts may cause damage.
Wrap all threaded connections with pipe tape
available at your local plumbing supply store.
Always wrap in a clockwise direction. The fittings
should be installed by a state-licenced plumber.
Tools: Maintenance
Safety Tips
Things You May Need
Important Points
IAPMO/cUPC Listed
Meets A112.18.1
Standards
Please note :
Final achievable flow rate is dependent on the outlets fitted, see relevant outlets (spouts, roses, sprays) for fully
assembled product flow rate.

4
Steps 1-3
Installation Procedure
Lefroy Brooks always recommends that plumbing products be installed by a licensed professional.
Shut off main water supply before installation.
1
2
3
Before installing the valve into the wall,
please note that a distance between 3
1/8"~ 4 1/8" (80mm ~ 105mm) from the
wall surface to the back of valve should be
left, so that it can fit the trim kit.
Install valve assembly into the wall.
Cut a hole on the wall surface for fitting the
trim kit. The hole dimension should be as
shown.
4Throw away the protective caps only when
the building construction is completed and
you are ready to fit the trim.
4
2
1
Marble wall
3 1/8”-4 1/8”
80-105
3
5 3/8"~5 1/2"
(136mm~140mm)
1 3/8"~1 5/8"
(35mm~42mm)
2 5/8"
(67mm)
3 9/16"~4 1/8"
(90mm~105mm)

5
Steps 5-8
Installation Procedure
Lefroy Brooks always recommends that plumbing products be installed by a licensed professional.
Shut off main water supply before installation.
4
5
6
7
Take out the stopper.
Turn on the flow controller. Turn the
thermostatic cartridge till you get the water
temperature at 38°. Suggestion: attach a
hose to the outlets and guide the water to
the basin or another container to test the
temperature and prevent it from spilling on
the floor.
Turn off the water supply. Install the
stopper and make sure its "B" plane, as
shown, is horizontal and on the left side.
8Fix the stem extension and the adjusting
ring.
7
8
5
6

6
Steps 9-12
Installation Procedure
Lefroy Brooks always recommends that plumbing products be installed by a licensed professional.
Shut off main water supply before installation.
9
10
11
Install the canopies.
Fix the front plate with screws.
Fix the canopy with screw. When it is fixed,
ensure the temperature-limit-button is in
the horizontal position. Turn clockwise to
increase the temperature and turn counter-
clockwise to reduce the temperature.
12 Install handle assembly with set screws.
9
10
11
12
Set screw
Horizontal

7
Parts List
Exploded View
1 Screw (008772)
2 Cross handle (069910)
3 Screw (008994)
4 Adaptor (018210)
5 O-ring (048060)
6 Set screw (065086)
7 Canopy (071437)
8 Adjusting ring (104295)
9 Front panel (006596)
10 Seal (013218)
11 Plug (028008)
12 Handle seat (215479)
13 Button (036272)
14 Spring (005157)
15 Pin (003147)
16 Handle stem (108926)
17 Handle sleeve (038104)
18 Adaptor (205469)
19 Screw (008255)
20 Screw (008186)
21 Extension stem (110438)
22 O-ring (048085N)
23 Sleeve (041817)
24 Allen key (031003)
25 Allen key (031220)
8
7
13
6
4
1
3
2
12
23
21
16
17
14
15
20
24
10
5
18
19
9
22
25
11

For additional assistance or service call
718-302-5292
9am to 5pm EST Monday to Friday
LEFROY BROOKS INC, 1828 TROUTMAN STREET, RIDGEWOOD, NY, 11385
TELEPHONE: [phone]. FAX: [phone]
The use of trademarks, product design and artwork is subject to licence or agreement with LBIP Ltd. The design
registrations, trademark registrations and copyrights are protected by law and the use or reproduction outside the terms of an agreement is prohibited.
The right to modify designs and dimensions is reserved. Christo Lefroy Brooks is a member of ACID (Anti Copying in Design).
© LBIP LTD 2012
www.lefroybrooks.com