Legacy 21011 User manual

(1) Pan Head
Screws
(actualsize)
SS
SS
SINGLEINGLE
INGLEINGLE
INGLE DD
DD
DROPSIDEROPSIDE
ROPSIDEROPSIDE
ROPSIDE CC
CC
CRIBRIB
RIBRIB
RIB//
//
/
DD
DD
DAYBEDAYBED
AYBEDAYBED
AYBED WITHWITH
WITHWITH
WITH HH
HH
HIDDENIDDEN
IDDENIDDEN
IDDEN
HH
HH
HARDWAREARDWARE
ARDWAREARDWARE
ARDWARE ANDAND
ANDAND
AND DD
DD
DRAWERRAWER
RAWERRAWER
RAWER..
..
.
LH01799:01/01 JCHE.p65
• READALLINSTRUCTIONSWITHCAREBEFORESTARTINGTHEASSEMBLYPROCEDURE.
• YOUWILLNEED#1AND#2PHILLIPSSCREWDRIVERS,ASLOTTEDSCREWDRIVER,A10mmWRENCH,
ANDTHEENCLOSEDALLENWRENCHA FORASSEMBLYOFTHISCRIB.(Note:10mmoradjustablewrench)
PARTSENCLOSEDINHARDWARE BAG (NOTED WHEN SHOWNACTUALSIZE)
A(2) Upper
Guide
Bushings
(actualsize)
(2) Lower
GuidePins
(actualsize)
(2) Joint Connector Screws
(actual size)
(2) Flat Head
Machine
Screws (actual
size)
(1) Allen
Wrench
(8) Allenhead Bolts (actual size)
21011, 21031, 21051, 21061, 21071, 21121
(style may vary)
(4) K-D Bolt
Plugs
(actualsize)
(8) Allenhead
K-D Bolts
(actualsize)
(5) Cam
Locks
(actualsize)
(4) Casters(5) Threaded Connectors
(actualsize)
(4) Nuts
(actualsize)
(6) Flathead Phillips Wood
Screws (actual size)
PARTSENCLOSEDINCARTON
(1) Support Rail
(1) Metal Drawer
Rail-Right
(1) Metal Drawer
Rail - Left
(1) Drawer Cabinet
Rail-Right
(1) Drawer Cabinet
Rail - Left
(2) Wood Drawer
Rails
HH
II
JJ
KK
MM
V
1
CHILD CRAFT INDUSTRIES, INC.
P.O. Box 444, Salem, IN USA 47167-0444
PH: 812-883-3111 - FAX: [phone] - http://www.childcraftind.com
ASSEMBLY DIRECTIONS AND PARTS LIST
BC
H
DEF
IGJ
KXZ
BB LL(6) Flathead Phillips
Wood Screws
(actualsize)
(1) Drawer End - Right
(1) Drawer Front
(1) Drawer Back
(1) Drawer Bottom
(2) Stretchers
(1) Drawer End - Left
QR
Y
S
T
U

P ARTS E NCLOSED IN C ARTON ( CONTINUED )
(1) Spring
(ScissorArmsattached)
(1) Dropside
(1) Footboard
(style may vary)
(1) Headboard
(style may vary)
LMP (1) Stationary Side
NOTE: Plastic and Metal Tracks
are installed in each end.
ON
STEP1-DIAGRAM1: HARDWARE APPLICATION TO HEADBOARD
& FOOTBOARD AND ATTACH STATIONARY SIDE.Lay Footboard Mand Headboard Ldown horizontally,
(outside
facing down) asshown. Insert an UpperGuideBushingCandaffix
a Flathead Machine Screw Bas shown to Footboard M.Note:
LH01799:01/01
2
Carefullylayout allhardwareandparts.CheckquantitiesandmatchtoHardwareBag&CartonPartsLists.Ifapartismissingorbroken
contactyourdealerorLegacy,812/883-3111,(FAX [phone]),http://www.childcraftind.com,forareplacementpartorinstructional
literature.Beforecontactingidentifyyourcrib.IdentificationnumbersarestampedontheunderneathedgeofbottomrailofFootboardM,
HeadboardL, cribsideOorNorstampedona labelattachedtotheinsidefaceof Footboard Mbottomrail.Recordthecomplete
modelidentificationnumbernow:#__________________.DONOTSUBSTITUTEPARTS!
PREPARATION:
use hand screwdriver not battery or electric driver. Tighten but do not overtighten. (Overtightening can cause the Upper Guide Bushing C to
compress down.) The Upper Guide Bushing Cmust slide freely in groove of the metal track attached to the ends of Dropside O. At this time read
andunderstandDiagram 4 beforeproceeding. Testtoseethat the metal top track will slide freelyoverUpperGuideBushingC,ifnotloosenFlathead
Machine Screw Buntil the metal top track slides freely, but make sure Upper Guide Bushing Cis securely attached. Insert a Lower Guide Pin D
into its receiving hole located on inside face of Footboard Mexactly as shown. Follow the same procedure to install the remaining Upper Guide
Bushing Cand the Lower Guide Pin Dto Headboard L. Lower Guide Pins Dwill remain loose in their receiving holes. Follow Diagram 1 exactly
for installing Wood Drawer Rail MMand Drawer Cabinet Rail-Right JJ to Footboard M using (3) Flathead Phillips Wood ScrewsBB. Follow
thissameprocessforinstallingWoodDrawerRailMMandDrawerCabinetRail-LeftKKtoHeadboardLusing(3)FlatheadPhillipsWoodScrews
BB.
BB
JJ
MM D
B
C
G
N
M
Roller Post
Post
Threaded
inserts
(style may vary)
With the Footboard Mstill
laying horizontally, and the
Drawer Track JJ facing
up, line up the holes on the
Stationary Side Nwith the
threaded inserts in the post
on Footboard M. Insert
(2) Allenhead K-D Bolts G
throughtheholesintheSta-
tionary Side Nand tighten
securely using Allen
Wrench Ain the threaded
inserts in the post. Tilt the
Footboardupuntilitisstand-
ing on its posts. Attach the
loose end of the Stationary
Side Nto the Headboard
L using the same process
as described in attaching
the Footboard Mto the
Stationary Side N. Tighten
K-D Bolts Gsecurely.

STEP 2-DIAGRAM 2:ATTACH THE STRETCHERS TO THE
FOOTBOARD & HEADBOARD
3
LH01799:01/01
1.Decide on your preference of height placement of Spring
P. You have three position choices, highest, middle and
lowest holes in Spring Pas shown. After you select your
height, attach one end of the long end of Scissor Arm
Assembly to Spring Pby first inserting an Allenhead Bolt
Hthrough selected position hole in Spring Pthen through
one end of Scissor Arm Assembly,add a Nut Zexactly as
shown. Repeat this procedure until one end of each of the
(4) Scissor Arm Assemblies is attached to Spring Pat the
same height position. Tighten all (4) Allenhead Bolts H while
holding Nuts Zwith a 10mm or adjustable wrench. Tighten
each assembly securely .
2.Carefully lift Spring Pinto the crib. Spring Pwill attach
to the outside holes in the two installed Stretchers Y. Insert
an Allenhead Bolt Hfirst through the remaining long end of
the Scissor Arm Assembly into the threaded insert as
shown and follow the procedure exactly. Repeat the
procedure with the remaining (3) long ends of the Scissor
Arm Assemblies to Stretcher Y. Tighten each assembly
securely.
3.Whenever you decide on another height position first
remove the crib mattress. Remove Spring Pby detaching
the spring from the Stretchers Yby loosening and removing
the (4) Allenhead Bolts Hinstalled in 2.above using Allen
Wrench A. Carefully lift the spring from the crib. Make your
selected height position change by following 1. of this Step.
Then follow 2.to reinstall Spring P, again tighten all
Allenhead Bolts Hsecurely as directed.
Read this entire step before starting the procedure
to select a spring height position and to attach
Spring P to Stretchers Y.
STEP 3-DIAGRAM 3:ATTACH SPRING TO STRETCHERS IN CRIB
Install this Stretcher first.
Attach both ends before installing
the other Stretcher Y
G
EG
N
Install this Stretcher last.
Attach this end to Headboard L
following the same process described
for the Footboard M
M
Outside Face
N
M
G
E
Y
NOTE: Drawer track is not shown (Step 1) to
allow a clear view of the assembly process.
Smooth side
of Spring P
is the top
Mount Nut Z on
opposite end as shown
NOTE: CRIBISDELEATEDFROMTHISDIAGRAM
FORACLEARVIEWOFTHESPRINGASSEMBLYP
BEINGATTACHEDTOTHESTRETCHERY.
lowest position
middleposition
highest position
Scissor Arm
assembly
Z
H
Y
Install Stretcher Ywhich is closest to the Stationary Side Nusing (2) K-
D Bolt Plugs Eand (2) Allenhead K-D Bolts Gas shown. K-D Bolts Gwill
be inserted through the outside face of Footboard Mand Headboard L
into the receiving hole in the ends of Stretcher Y. The Dowel in the end of Stretcher Ywill be inserted into the upper hole in Footboard Mand
Headboard L. Insert a K-D Bolt Plug Einto the hole near the end of Stretcher Y. Pull each K-D Bolt Gout just enough to allow K-D Bolt Plug E
tobe fullyinserted intoitsreceiving hole. (Note: itmaybenecessary toloosen oneofthe lowerbolts Gwhich were installedduring Step1). Loosening
one of the lower bolts Gwill allow the Stretcher Yto move easier into its proper location. Take care to tighten securely any bolt loosened after
the completion of this step. Install the other Stretcher Yto Headboard Lfollowing the same process.
ENLARGED VIEW

LH01799:01/01
4
CheckthefunctionofDropsideO.TolowertheDropside,lift
upontheDropsidetoprailwithyourhandnearthemiddleand
then press in with your knee on the center of the Dropside
bottomrail.TheDropsidewillthenlower.TolocktheDropside
in the raised position, just lift it up until it locks into place.
AlwaysverifythatbothendsoftheDropsidearelockedin the
raised positionwheneverchildisplaced incrib.Onlylower
theDropside when attendingtochild.
PREPARATION FOR INSTALLATION OF DROPSIDE:
LoosenthetwoAllenheadBoltsG(Dropside only) which
attachtheStretcherYtotheHeadboardLandFootboard
Mtopreparefor Dropside Oinstallation.Backoutthese
(2) Bolts a full (8) revolutions each, but do not remove the
bolts . The Stretcher Ywill now be loose.
Install Dropside Oby following substeps Ithrough IV
listed below. Refer to Diagram. (It would be helpful to
have a friend assist you with this procedure.) Note: the
outside location of Dropside Oas shown in Dia-
gram.
I. Note: During the Dropside O installation procedure
use extreme caution when Top Tracks and Lower Tracks
make contact with Upper Guide Bushings C and Lower
Guide Pins D so as not to damage the finish of this crib.
II. Insert the Upper Guide Bushings C (mounted to
Footboard M and Headboard L in STEP 1) into the
Upper Tracks (metal) which were factory mounted to
Dropside.Hold the Dropside Oat approximately 30
degrees from vertical as shown.
III. Once both ends are engaged, then carefully allow
Dropside Oto slide downward. Then rotate the bottom
end of the Dropside Ountil it is nearly vertical. (Note:
Rotation will be stopped when the dropside O touches
the Lower Guide pins D . Carefully let the Dropside O
slide down until it is as low as it can go.
IV. READ THIS STEP COMPLETELY BEFORE PROCEEDING. Next, lift
Dropside OO
OO
Oapproximately two inches (2") vertically. This will put Dropside O
in the proper vertical alignment with the Lower Guide Pin Dwhich will be
inserted into the Lower Tracks (Right & Left).
Flex the bottom end of the corner post on the Dropside side of Footboard M
away from the Dropside O. The purpose of this process is to create a gap
for the Lower Guide Pins Dto pass through so that the Lower Guide Pins
can be inserted into the long groove of the plastic Lower Tracks. As you
prepare to accomplish this please note the following:
If the Stretcher Assembly Ywas not loosened enough (as described in
PREPARATION FOR INSTALLATION OF DROPSIDE in the beginning of
this step) there will not be enough slack to create the necessary gap required
for the Lower Guide Pin Dto pass through. Prematurely forcing the pin
through a gap with inadequate clearance could damage the finish on the
Dropside O. If your crib has too small of a gap, then lower Dropside Oto its
lowest position and check to verify that preparation at beginning of Step 4
was performed correctly.
If it was performed correctly, but the gap is still too small, it may be because
the Stretcher Yassembly needs to be pulled away from the bottom rails of
the Footboard Mor Headboard L. Check to verify that the Stretchers Y
have been pulled away from the bottom rails.
After the Lower Guide Pin Dhas been installed into the long groove on
Footboard M, then repeat this process on Headboard L. After both Lower
Guide Pins Dare installed, very carefully and slowly raise the DropsideO
up until it locks into its raised position. Be very careful to watch to ensure that
the Lower Guide Pins Dlocated in the grooves do not slip out during the
process of raising Dropside O.
STEP 4-DIAGRAM 4: INSTALLATION OF DROPSIDE.
Refer to Diagram 2. Tighten the (2) Allenhead Bolts Gwhich were installed
inStep2 toattachStretcherYto HeadboardLand Footboard Mbut were
loosenedinStep4.Besurethe(2) AllenheadBoltsGaretightenedsecurely.
Check these screws periodically and tighten if needed.
outside face of dropside
IIII
IIII
II.Engagement
of
(metal) Top
Track and
UpperGuide
Bushing CC
CC
Cwill
start at bottom
of Metal Top
Track (see
enlarged
section view
below).
II.II.
II.II.
II. ENLARGED SECTION VIEW
Engagement of Metal Top Track
and Upper
Guide Bushing CC
CC
C
IV.IV.
IV.IV.
IV. ENLARGED VIEW
III.III.
III.III.
III. Lower Track (plastic)
NOTE: Place short groove
toward inside of crib.
FLEX
IV.IV.
IV.IV.
IV. Then insert Lower Guide Pin DD
DD
D
into long groove in Lower Track (plastic).
long groove
Dropside
OO
OO
O post
Corner post of Footboard
MM
MM
M
ONM
D
G
X
Metal Top Track
OMC
O
M
30°
Y

LH01799:01/01 5
STEP 5-DIAGRAM 5: BUILD UPOF DRAWER.
STEP 5C. Attach Drawer End-Right Q, Drawer End-Left Rand
SupportRailVtoDrawerFrontS. InsertCamLocksIintotheir
receiving holes in Support Rail V, Drawer End-Right Qand
Drawer End-Left R, then lower onto the Threaded Connectors
K. NOTE:AlignthelargeopeninginCamLockIto receivethe
headof theThreadedConnectorKafterCamLocksare inserted
in receiving holes.Rotate CamLocksIclockwise 1/2turnusing
a phillips screwdriver.
STEP 5A.AttachMetalDrawerRail-RightHHtoDrawerEnd-
Right Qby matching to pilot holes, affix (3) Flathead Phillips
Wood Screws LLas shown. Repeat this procedure with
Metal Drawer End-Left IIto Drawer End-Left R, again affix
with the remaining (3) Wood Screws LL. Tighten screws
securely. DO NOT OVERTIGHTEN.
STEP 5B. Install Threaded Connectors K
into Drawer Front S as shown. DO NOT
OVERTIGHTEN.
STEP 5D. InstallDrawerBottomU byinserting
into grooves located in Drawer End-Left R,
Drawer End-Right Q and Drawer Front S.
STEP5E. ToinstallDrawerBackT,ConnectorsJwillbeinserted
in both sides of Drawer Back T and tightened. Insert Panhead
ScrewF throughits receiving hole in DrawerBack T, then into
pilot hole in end of the Support Rail V. Tighten all fastening
devices securely.
DRAWER PLACEMENT: Place the drawer under the crib by
insertingtherollersonthedrawertrack(attachedtothedrawer)
into the channel of the drawer rails attached under the crib.
LL HH
II R
K
S
Drawer
Bottom
Groove
HH
HH
S
I
K
R
K
I
Q
V
RU
V
S
T
J
F
R
U
Receiving Holes
for Cam Locks I
LL
Q
I

Locate the (4) Casters X, insert one into socket in each
lower corner post of Headboard Land Footboard M.
Caster Xdesign may vary according to your particular
model. CAUTION: If crib is placed on exceptionally thick
carpet, take care when crib is rolled as casters could
catch on thick carpet pile and possibly cause breakage
to lower corner posts of crib.
Place a purchased mattress on Spring Pand crib is
ready for use.
Check periodically to be sure screws and bolts
(fastening devices) remain tightened as instructed
in each step of these assembly instructions.
After completing crib assembly, and after making yourself
aware of the Warnings, Cautions, Cleaning, Storage,
Use and Maintenance of crib, store the assembly
directions in the plastic pouch which was pre-attached to
Spring P. For future referral to assembly directions you
will only need to remove them from the plastic pouch. We
caution you not to store excess hardware in plastic pouch
as this would be a danger to child if retrieved by him/her.
AA
AA
ASSEMBLYSSEMBLY
SSEMBLYSSEMBLY
SSEMBLY DD
DD
DIRECTIONSIRECTIONS
IRECTIONSIRECTIONS
IRECTIONS
TOTO
TOTO
TO CC
CC
CONVERTONVERT
ONVERTONVERT
ONVERT CC
CC
CRIBRIB
RIBRIB
RIB
TOTO
TOTO
TO
AA
AA
ADD
DD
DAYBEDAYBED
AYBEDAYBED
AYBED..
..
.
(Crib mattress will be
used as seating for
Dayed) Referto Sketch
A .Follow Installation of
Dropside directions,
(STEP 4),inreverseor-
der for the removal of
Dropside Ousing ex-
treme caution when
doing so to avoid dam-
age to the finish of your
crib/daybed. Remove
Upper Guide Bushings
Cand Lower Guide
Sketch A
W
STEP6:FINISHING TOUCHES.
PinsDas directed inStep 1- Diagram 1, inreverse order(NOTE:
itisveryimportantthat the LowerGuide PinDisremovedand
storedawayfromthechildbecauseitisnotattachedtothecrib,
andifremovedbythechildandswallowed,LowerGuidePinD
could be a choking hazard). Store removed Dropside Oand
hardware so you will be able to reassemble into a crib if you wish
to do so in the future. Only use the lowest position placement of
Spring Pwhen using as a daybed, (refer to Step 3 - Diagram 3) .
Periodicallycheckandtighten (ifneeded) fasteningdevices (screws
and bolts) as instructed. Return the assembly directions to the
plastic pouch attached to the crib spring for future availability.
Style may varyStyle may vary
Style may varyStyle may vary
Style may vary
LH01799:01/01
6
•TO LOWER & RAISE CRIB DROPSIDE: To lower lift up on the Dropside top rail with your hand near the center and then press in with your knee on the
center of the Dropside bottom rail. To lock the Dropside in the raised position, lift up from center until it locks into place. Always verify that both ends of
the Dropside are locked in the raised position when child is placed in crib. Only lower Dropside when attending to child.
•MAINTENANCEOFYOURLEGACYCRIB: Uponcompletionofassemblybesurescrewsandbolts(fasteningdevices)aretightenedsecurely.Aperiodic
check should be made of fastening devices and tighten if needed. Before each usage or assembly, inspect crib for damaged hardware, loose joints,
missing parts or sharp edges. DO NOT use crib if parts are missing or broken. Ask your Dealer or LEGACY (812/ 883-3111), [email protected]
for replacement parts and instructional literature if needed. Include Model Identification Number with your request which you recorded on page 1. DO NOT
substitute parts. DO NOT make any alteration to this crib.
• CLEANINGINSTRUCTIONSFORYOURLEGACYCRIB: Mixtogetheramildsolutionofgentledishwashingliquidandwater,applytocribsurfaceusing
a soft clean cloth lightly dampened in the solution. Rinse with clear water again using a soft clean cloth then dry all surfaces thoroughly with a soft dry
cloth.NOABRASIVECLEANERS,SCOURINGPADS,STEELWOOL,ORCOARSERAGSSHOULDBEUSEDTOCLEANTHISFINEFURNITURE.
• STORAGEANDUSEOFYOURLEGACYCRIB: Aprintedplasticpouchisattachedtothecribspringforthepermanentstorageoftheassemblydirections.
AftercompletingtheassemblyprocessyouareadvisedtoreadandbeawareofallWARNINGS,CAUTIONS,CLEANING,STORAGE,USEANDMAINTENANCE
noticescontained in this setofassemblydirections and printed ontheplasticpouch attached to crib spring.Youwill then place the complete setofassembly
directions into the plastic pouch for future referral. We caution you not to place excess hardware in the plastic pouch as it could present danger to a child
if retrieved and it could also puncture crib mattress. When storing crib use CAUTION as extreme temperature or humidity changes could be harmful. Use
CAUTION when a vaporizer is in use, always aim vapor stream away from crib as well as away from any other wood furniture item.
ASSEMBLED CRIB
(STYLE MAY VARY)
M
N
L
O
X
Q
R
S

ΦΦ
ΦΦ
ΦFAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY INSTRUCTIONS COULD RESULT
IN SERIOUS INJURY OR DEATH.
ΦΦ
ΦΦ
ΦREAD ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP INSTRUCTIONS FOR FUTURE
USE.Aplasticpouchisattachedtocribspringforpermanentstorageoftheinstructionalliterature.
ΦΦ
ΦΦ
ΦBEFORE EACH USAGE OR ASSEMBLY, INSPECT CRIB FOR DAMAGED HARDWARE, LOOSE
JOINTS,MISSINGPARTSORSHARPEDGES.DONOTUSECRIBIFANYPARTSAREMISSINGOR
BROKEN. ASK YOUR DEALER OR LEGACY, P.O. BOX 444, SALEM, IN 47167-0444 USA (812/883-
3111), [email protected] FOR REPLACEMENT PARTS AND INSTRUCTIONAL LITERA-
TURE IF NEEDED. INCLUDE MODEL IDENTIFICATION NUMBERS WITH YOUR REQUEST WHICH
YOU RECORDED ON PAGE ONE. DO NOT SUBSTITUTE PARTS.
ΦΦ
ΦΦ
ΦAFTER RAISING SIDE, MAKE SURE LATCHES ARE SECURE.
ΦΦ
ΦΦ
ΦWHENCHILDIS ABLETO CLIMBOUTOR REACHESTHE HEIGHTOF35INCHES(90 CENTIME-
TERS) THE CRIB SHALL NO LONGER BE USED.
ΦΦ
ΦΦ
ΦDO NOT PLACE CRIB NEAR WINDOW WHERE CORDS FROM BLINDS OR DRAPES MAY
STRANGLE A CHILD.
ΦΦ
ΦΦ
ΦIF REFINISHING, USE A NONTOXIC FINISH SPECIFIED FOR CHILDREN'S PRODUCTS.
ΦΦ
ΦΦ
ΦDO NOT LEAVE CHILD IN CRIB WITH SIDE LOWERED. BE SURE SIDE IS IN RAISED AND
LOCKED POSITION WHENEVER CHILD IS IN CRIB.
ΦΦ
ΦΦ
ΦWHEN CHILD IS ABLE TO PULL TO STANDING POSITION, SET MATTRESS TO LOWEST
POSITION AND REMOVE BUMPER PADS, LARGE TOYS AND OTHER OBJECTS THAT COULD
SERVE AS STEPS FOR CLIMBING OUT.
ΦΦ
ΦΦ
ΦNEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC FILM AS MATTRESS COVERS
BECAUSE THEY CAN CAUSE SUFFOCATION.
ΦΦ
ΦΦ
ΦDO NOT USE A WATER MATTRESS WITH THIS CRIB.
ΦΦ
ΦΦ
ΦREPLACE TEETHING RAIL(S) IF DAMAGED OR LOOSE.
ΦΦ
ΦΦ
ΦSTRINGS CAN CAUSE STRANGULATION! DO NOT PLACE ITEMS WITH A STRING AROUND A
CHILD'S NECK, SUCH AS HOOD STRINGS OR PACIFIER CORDS. DO NOT SUSPEND STRINGS
OVER A CRIB OR ATTACH STRINGS TO TOYS.
ΦΦ
ΦΦ
ΦREMOVE ALL CRIB TOYS WHICH ARE STRUNG ACROSS CRIB AREA WHEN YOUR CHILD IS
BEGINNING TO PUSH UP ON HANDS AND KNEES OR IS 5 MONTHS OF AGE, WHICHEVER
OCCURS EARLIEST. THESE TOYS CAN CAUSE STRANGULATION!
ΦΦ
ΦΦ
ΦWHEN DISASSEMBLING THIS CRIB, DO NOT REMOVE ANY ITEM ATTACHED WITH WOOD
SCREWS.
ΦΦ
ΦΦ
ΦALWAYS ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY CHECKING REGULARLY,
BEFORE PLACING THE CHILD IN THE CRIB, THAT EVERY COMPONENT IS PROPERLY AND
SECURELY IN PLACE.
WW
WW
WARNINGARNING
ARNINGARNING
ARNING
LH01799:01/01JCHE.p65
CHILDCRAFTINDUSTRIES,INC.
P.0.Box444,Salem,IN USA 47167-0444
•PH-812/883-3111 •FAX-812-883-1819
http://www.childcraftind.com
ENGLISH
MADE IN croatia
CACA
CACA
CAUTIONUTION
UTIONUTION
UTION
ΦΦ
ΦΦ
ΦANYMATTRESSUSEDINTHISCRIBMUSTBEATLEAST27-1/4INCHES(69
CENTIMETERS),BY51-5/8INCHES(131CENTIMETERS),WITHATHICKNESSNOT
EXCEEDING 6 INCHES (15 CENTIMETERS). The dimensions of the mat-
tress shall be taken from seam to seam or edge to edge where
appropriate.
ΦΦ
ΦΦ
ΦUPONCOMPLETIONOFASSEMBLYBESUREALLSCREWS,BOLTSAND
FASTENINGDEVICESHAVEBEENTIGHTENEDSECURELY.AFREQUENTCHECK
SHOULDBEMADEOFALLSCREWS,BOLTSANDFASTENINGDEVICESAND
TIGHTENIFNEEDED.
LH01799:01/01 7
▲
!