Legacy SINGLE DROPSIDE CRIB User manual

(4) K-D
Bolt Plugs
(actualsize)
SINGLE DROPSIDE CRIB/
DAYBED WITH DRAWER AND
HIDDEN HARDWARE.
LH02704:04/00LH02704:04/00
LH02704:04/00LH02704:04/00
LH02704:04/00 JCHE.p65 1
• READALLINSTRUCTIONSWITHCAREBEFORESTARTINGTHEASSEMBLYPROCEDURE.
• YOUWILLNEED#1AND#2PHILLIPSSCREWDRIVERS,ASLOTTEDSCREWDRIVER,A7/16"
WRENCH,ANDTHEENCLOSEDALLENWRENCH(S)(S)
(S)(S)
(S)FORASSEMBLYOFTHISCRIB.
PARTS ENCLOSED IN HARDWARE BAG ( NOTED WHEN SHOWN ACTUAL SIZE )
A(8) Slotted/
Phillips
Machine
Screws
(actualsize)
(4) Scissor Arm Assemblies (2) Upper
Guide
Bushings
(actualsize)
(2) Lower
GuidePins
(actualsize)
(20) Lock Nuts
(actualsize)
(4) Casters (20) Pan Head
Machine Screws
(actualsize)
(2) Flat Head
Machine Screws
(actualsize)
(2) End Plates - Right
(2) End Plates - Left
(1) Allen Wrench
(2) Allen Bolts (actual size)
(style may vary)
CHILD CRAFT INDUSTRIES, INC.
P.O. Box 444, Salem, IN USA 47167-0444
PH: 812-883-3111 - FAX: [phone] - http://www.childcraftind.com
ASSEMBLY DIRECTIONS AND PARTS LIST
BCDG
HIJL
S
MN
U
K
R
(3) R/H Slotted Phillips Wood Screws
(actualsize)
(8) F/H Slotted Phillips Wood Screws
(actualsize)
(2) Allen Bolts (actual size)
P
E(4) Mini Blocks
(actual size)
(16) Washers
T
O
(actualsize)
(2)P/HPhillips
Wood Screws
(actualsize)
(8)F/HPhillips
Wood Screws
F
P ARTS E NCLOSED IN C ARTON
(actualsize)
aa
aa
a(2) Drawer Rails
bb
bb
b(2) Drawer Ends
cc
cc
c(1) Drawer Partition
dd
dd
d(1) Drawer Front (finished side)
ee
ee
e(1) Drawer Back
ff
ff
f(1) Drawer Bottom
gg
gg
g(1) Drawer Rail-Right
hh
hh
h(1) Drawer Rail-Left
ii
ii
i(1) Drawer "Cabinet Rail"-Right
jj
jj
j(1) Drawer "Cabinet Rail"-Left
21021
H00117
H01214
H01217 H00291
H00328 H00132 H00116
H00109
H00211
H01205 H01206
H00371
H01124 H01157
H00133
H00164
H00112
H00190
H01101 H00288

2LH02704:04/00LH02704:04/00
LH02704:04/00LH02704:04/00
LH02704:04/00
(2) Stabilizing Bars (attached to Spring ( W )
V
X
(1)
Drop-
side
Y
(1)
Sta-
tionary
Side
wide
end
rail on
each
end
P ARTS E NCLOSED IN C ARTON ( CONTINUED )
(1) Spring
(1) Footboard (1) Headboard
W
ZAA
(style may vary)
(style may vary)
plastic pouch
(storage for
Assembly Directions)
STEP 1-DIAGRAM 1:SPRING ASSEMBLY.
P REPARATION
Carefully remove and lay out all hardware and parts. During the assembly process whenever using screws or bolts (fastening devices), check each with
this hardware list, by letter and size identify by placing each fastening device on the diagram of the item which is sketched actual size. Be sure to use
the proper size specified in the assembly directions. Hardware Bag may contain extra fastening devices. Check quantities and match to Hardware Bag
and Carton Parts Lists. If a part is missing or broken contact your dealer or Legacy, 812/ 883-3111, (FAX [phone]), http://www.childcraftind.com
for a replacement part or instructional literature. Before making this contact identify your crib. Model Identification numbers are stamped on a label attached
to the inside face of Footboard ZZ
ZZ
Zbottom rail. Record the complete model identification number now: #____________________. Include this number with
a request for a part or literature for your crib. DO NOT SUBSTITUTE PARTS!
Attach the short section of the (4) Scissor Arm Assemblies BB
BB
Bto Spring WW
WW
Wusing (4) Pan Head
Machine Screws II
II
Iand (4) Lock Nuts GG
GG
Gplaced exactly as shown in Diagram 1. NOTE: The
metal threads of Lock Nuts G to be inserted first over Pan Head Machine Screws
II
II
I as shown in Enlarged Section View . Be sure to use the proper
receiving holes in Spring WW
WW
Was shown . This procedure will be accomplished from the underside of Spring WW
WW
W. Tighten all (4) Pan Head Machine Screws
II
II
Iwhile holding Lock Nuts GG
GG
Gwith a 7/16 inch wrench. Tighten each assembly securely.
Long arm of Scissor Arm Assembly BB
BB
B
Short arm of
Scissor Arm
Assembly BB
BB
B
Short arm of Scissor Arm Assembly BB
BB
B
lowest position
middleposition
highest position
UNDERSIDE OF SPRING WW
WW
W
plastic pouch
See Enlarged View
plastic
insert in
Lock Nut GG
GG
G
B
ENLARGED SECTION VIEW
Long arm of
Scissor Arm
Assembly BB
BB
B
IG
B
W
I
B
WI
G

LH02704:04/00LH02704:04/00
LH02704:04/00LH02704:04/00
LH02704:04/00 3
STEP 2-DIAGRAM 2:ASSEMBLY OF STABILIZING BARS.
Mount an End Plate - Right NN
NN
Nand an End Plate - Left MM
MM
M to ends of each Stabilizing
Bar VV
VV
Vusing (4) Pan Head Machine Screws II
II
Iand (4) Lock Nuts GG
GG
Gin each
Stabilizing Bar VV
VV
Vexactly as shown. IMPORTANT: End Plates MM
MM
M&
NN
NN
Nmust be positioned in the correct mounting holes to Stabilizing
Bars VV
VV
Vexactly as shown. Tighten down Pan Head Machine Screws II
II
Iand Lock Nuts GG
GG
Gsecurely using a phillips screwdriver and a 7/16 inch wrench.
STEP 3-DIAGRAM 3:ATTACH HARDWARE
TOHEADBOARD &FOOTBOARD
Lay Footboard ZZ
ZZ
Zand Headboard AAAA
AAAA
AA down horizontally, (outside facing down) as shown.
Insert an Upper Guide Bushing CC
CC
Cand affix with a Flathead Machine Screw JJ
JJ
J to Footboard
ZZ
ZZ
Z. Note: use hand screwdriver not battery or electric driver. Tighten down but do not
overtighten.
(Overtightening can cause the Upper Guide Bushing
CC
CC
C to compress down.) The Upper Guide Bushing CC
CC
Cmust slide freely in groove of
Metal Top Track. At this time read and understand Diagram 6 before proceeding. Test to see that Metal Top Track will slide freely over Upper
Guide Bushing CC
CC
C,if not loosen Flathead Machine Screws JJ
JJ
Juntil Metal Top Track slides freely, but make sure Upper Guide Bushing CC
CC
Cis securely
attached. Insert a Lower Guide Pin DD
DD
D into its receiving hole located on inside face of Footboard ZZ
ZZ
Zexactly as shown.Follow the same procedure
to install the remaining Upper Guide Bushing CC
CC
C and the Lower Guide Pin DD
DD
Dto Headboard AAAA
AAAA
AA. Next insert a Slotted/Phillips Machine Screw AA
AA
Ainto
each top threaded insert (located in routed circles) on both Footboard ZZ
ZZ
Zand Headboard AAAA
AAAA
AA, leave top Slotted/Phillips Machine Screw AA
AA
Aextended
(only allow Screws A to penetrate two to three revolutions into top insert) , as shown.
Now install Drawer Rail
aa
aa
a and Drawer "Cabi-
net Rail"-Right ii
ii
ito
Footboard ZZ
ZZ
Z, again ex-
actly as shown using
(4) 1-5/8" F/H Phillips/
Slotted Wood Screws
RR
RR
R,tighten securely.
Follow the same proce-
dure for hardware at-
tachmenttoHeadboard
AAAA
AAAA
AA as directed above
using theremainingUp-
per Guide Bushing CC
CC
C
affixing with Screw JJ
JJ
J
and the remaining
Lower Guide Pin DD
DD
D ex-
actly as shown.Now
install Drawer Rail aa
aa
a
and Drawer "Cabinet
Rail"-Left
jj
jj
jusingthere-
maining (4) 1-5/8" F/H
Phillips/Slotted Wood
Screws RR
RR
R.
NOTE: See Step 8. Install the enclosed Washers There if needed, between Drawer Rail aand Footboard Z
and/or Headboard AA. DO NOT INSTALL WASHERS DURING STEP 3.
Black plastic
insert in
Lock Nut G
See Enlarged View
ENLARGED SECTION VIEW
slot
Mor NEnd Plate
N
I
V
I
V
I
M
G
G
Align these three
holes with RR
RR
R
R
i
a
threaded insert in post
for attaching Stationary Side YY
YY
Y
RollerWheel
A
A
J
C
D
Z
slot

If necessary, loosen Screws AA
AA
Ain
Stabilizing Bar VV
VV
V (on Stationary Side of
crib). Align the receiving holes in each
end of the Stationary Side YY
YY
Ywith the
receiving holes located in corner posts
of Footboard ZZ
ZZ
Zand Headboard AAAA
AAAA
AA.
Insert an Allen Bolt UU
UU
Uinto each of the
top receiving holes and Allen Bolt P
into each of the bottom receiving holes.
Allow each to pass through the corner
posts of Headboard AAAA
AAAA
AA and Footboard
ZZ
ZZ
Z, then into the receiving holes in each
end of the Stationary Side YY
YY
Y. Insert
each of the (4) K-D Bolt Plugs LL
LL
Las
shown. Pull out each Allen Bolt just
enough to allow the K-D Bolt Plug LL
LL
Lto
be fully inserted in the receiving hole.
Tighten all (4) Allen Bolts until secure
using Allen Wrench SS
SS
S (enclosed) while
securing K-D Bolt Plugs LL
LL
Lwith a
standard screwdriver. CAUTION: DO
NOT OVERTIGHTEN. Securely re-
tighten Slotted/Phillips Machine Screws
AA
AA
Alocated in each end of Stabilizing Bar
VV
VV
Von stationary side of crib. Check all
screws and bolts periodically and tighten
if needed.
S TEP 5 - D IAGRAM 5: A TTACH S TATIONARY
S IDE TO H EADBOARD & F OOTBOARD
4LH02704:04/00LH02704:04/00
LH02704:04/00LH02704:04/00
LH02704:04/00
While Footboard ZZ
ZZ
Zis in a horizontal position place a Stabilizing Bar VV
VV
Vover an installed extended
Screw AA
AA
Abeing careful to place End Plate MM
MM
M& NN
NN
Nexactly as shown. Insert another Screw
AA
AA
Ainto the bottom insert, then tighten both screws. Place the remaining Stabilizing Bar VV
VV
V to
S TEP 4 - D IAGRAM 4: A TTACH S TABILIZING
B ARS TO H EADBOARD & F OOTBOARD
Footboard ZZ
ZZ
Zin the same manner, again pay close attention to ensure placement is exactly as shown and tighten Screws AA
AA
Asecurely. Set Footboard
ZZ
ZZ
Zupright and let top extended Screws AA
AA
A on inside of Headboard AAAA
AAAA
AA receive keyhole of Stabilizing Bars VV
VV
V, add Screw AA
AA
Ato bottom threaded insert
then tighten Screws AA
AA
A.
See Enlarged View
Corner post to receive Dropside
XX
XX
X
Corner post to receive
Stationary Side
YY
YY
Y
DC
Z
V
threaded
inserts
A
Bottom hole in
End Plate MM
MM
Mor NN
NN
N
Keyhole in End Plate
Extended Screw AA
AA
A
ENLARGEDVIEWENLARGEDVIEW
ENLARGEDVIEWENLARGEDVIEW
ENLARGEDVIEW
Z
A
V
a
i
Connected View
Y
L
L
L
L
U
UU
Z
Z
S
Y
V
P
S

LH02704: 04/00LH02704: 04/00
LH02704: 04/00LH02704: 04/00
LH02704: 04/00 5
PREPARATION FOR INSTALLATION OF DROPSIDE:
Loosen the four Slotted/Phillips Screws A(Dropside
only) which attach the Stabilizing Bar Vto the Headboard
AA and Footboard Zto prepare for Dropside XX
XX
X
installation. Back out these (4) Screws a full (8) revolu-
tions each, but do not remove the screws . The Stablizing
Bar V will now be loose.
Install Dropside X by following substeps I through IV
listed below. Refer to Diagram. (It would be helpful to
have a friend assist you with this procedure.) Note: the
outside location of Dropside XX
XX
Xas shown in Dia-
gram.
I. Note: During the Dropside X installation procedure
use extreme caution when Top Tracks and Lower Tracks
make contact with Upper Guide Bushings
CC
CC
C and Lower
Guide Pins
DD
DD
D so as not to damage the finish of this crib.
II. Insert the Upper Guide Bushings CC
CC
C (mounted to
Footboard Z and Headboard AA in STEP 3) into the
Upper Tracks (metal) which were factory mounted to
Dropside.Hold the Dropside Xat approximately 30
degrees from vertical as shown in Diagram.
III. Once both ends are engaged, then carefully allow
Dropside X to slide downward. Then rotate the bottom
end of the Dropside X until it is nearly vertical. (Note:
Rotation will be stopped when the dropside X touches
the Lower Guide pins
DD
DD
D . Carefully let the Dropside X
slide down until it is as low as it can go.
IV. READTHISSTEPCOMPLETELYBEFOREPROCEEDING. Next,
lift Dropside XX
XX
Xapproximately two inches (2") vertically. This will put
Dropside Xin the proper vertical alignment with the Lower Guide Pin
DD
DD
Dwhich will be inserted into the Lower Tracks (Right & Left).
FlexthebottomendofthecornerpostontheDropside sideofFootboard
Zaway from the Dropside X. The purpose of this process is to create
a gap for the Lower Guide Pins D to pass through so that the Lower
Guide Pins can be inserted into the long groove of the plastic Lower
Tracks. As you prepare to accomplish this please note the following:
If the Stabilizing Bar Assembly Vwas not loosened enough (as
described in PREPARATION FOR INSTALLATION OF DROPSIDE
in the beginning of this Step) there will not be enough slack to create
the necessary gap required for the Lower Guide Pin Dto pass through.
Prematurely forcing the pin through a gap with inadequate clearance
could damage the finish on the DropsideX. If your crib has too small
of a gap, then lower Dropside Xto its lowest position and check to
verify that preparation at beginning of Step 5 was performed correctly.
If it was performed correctly, but the gap is still too small, it may be
because the Stabilizing BarVassembly needs to be pulled away from
the bottom rails of the Footboard Z or Headboard AA. Check to verify
that the End Plates M & Nhave been pulled away from the bottom
rails until they touch the underside of the heads of loosened Slotted/
Phillips Machine Screws AA
AA
A.
After the Lower Guide Pin DD
DD
Dhas been installed into the long groove
on Footboard Z, then repeat this process on Headboard AA. After
both Lower Guide Pins D are installed, very carefully and slowly raise
the DropsideXup until it locks into its raised position. Be very careful
to watch to ensure that the Lower Guide Pins Dlocated in the grooves
do not slip out during the process of raising Dropside X.
Refer to Diagram 4. Tighten the (4) Slotted/Phillips Machine Screws
AA
AA
Awhich were installed in Step 4 to attach Stabilizing Bar Vto
Headboard AA and Footboard Zbut were loosened in Step 6. Be
sure the (4) Slotted/Phillips Machine Screws AA
AA
Aare tightened securely.
Check these screws periodically and tighten if needed.
Checkthe function ofDropside X.Tolower theDropside, lift upon
theDropsidetoprailwithyourhandnearthemiddleandthenpress
in with your knee on the center of the Dropside bottom rail. The
Dropsidewillthenlower.TolocktheDropsideintheraisedposition,
justliftitupuntilitlocksintoplace.Alwaysverifythatbothendsof
the Dropside are locked in the raised position whenever child is
placed in crib. Only lower the Dropside when attending to child.
Lower crib DropsideXX
XX
Xprior to proceeding with Step 7.
STEP 6-DIAGRAM 6: INSTALLATION OF DROPSIDE.
30 °
IIII
IIII
II. Engagement
of Metal Top
Track and
Upper Guide
Bushing CC
CC
Cwill
start at bottom
of Metal Top
Track
(see
enlarged
section view
below).
II. ENLARGED SECTION VIEW
Engagement of Metal Top
Track and Upper
Guide Bushing CC
CC
C
FLEX
III.Lower Track
( Plastic)
NOTE: Place short groove
toward inside of crib.
IVIV
IVIV
IV.ENLARGED VIEW
IV. Then insert Lower Guide Pin DD
DD
D into long
groove in Lower Track (plastic).
Corner post of Footboard
ZZ
ZZ
Z
long groove
short groove
Corner post to receive Dropside
XX
XX
X
Outside of Dropside XX
XX
X
XY
U
P
D
VZ
XZ
Z
X
C

STEP 7-DIAGRAM 7:ATTACH SPRING
TOSTABILIZING BARS INCRIB
LH02704:04/00LH02704:04/00
LH02704:04/00LH02704:04/00
LH02704:04/00
6
Read this entire step before starting the procedure to select a Spring WW
WW
W
height position and to attach Spring WW
WW
W to the Stabilizing Bars VV
VV
V. Review
Diagram 1.
11
11
1.Decide on your preference of height placement of Spring WW
WW
W. You have three position choices, highest, middle and lowest holes in Spring WW
WW
Ware
noted in Diagrams 1 and 7. After you select your height, attach one end of the long end of Scissor Arm Assembly BB
BB
Bto Spring WW
WW
Wby first inserting
a Pan Head Machine Screw II
II
Ithrough selected position hole in Spring WW
WW
Wthen through one end of Scissor Arm Assembly BB
BB
B,add a Lock Nut GG
GG
G, (with
metal threads of Lock Nuts
GG
GG
G to be inserted first), exactly as shown. Repeat this procedure until one end of each of the (4) Scissor Arm Assemblies
BB
BB
Bis attached to Spring WW
WW
Wat the same height position. Tighten all (4) Pan Head Machine Screws II
II
I while holding Lock Nuts GG
GG
Gwith a 7/16 inch wrench.
Tighten each assembly securely .
22
22
2.Carefully lift Spring WW
WW
Winto the crib. Spring WW
WW
Wwill attach to the outside holes in the two installed Stabilizing Bars VV
VV
V. Insert a Pan Head Machine Screw
II
II
Ifirst through the remaining long end of the Scissor Arm Assembly BB
BB
Bthrough the hole in Stabilizing Bar VV
VV
V, add a Lock Nut GG
GG
G (with metal threads
of Lock Nuts
GG
GG
G to be inserted first) . See Diagram 7 and follow the procedure exactly. Repeat the procedure with the remaining (3) long ends of the
Scissor Arm Assemblies BB
BB
Bto Stabilizing Bars VV
VV
V. Tighten all (4) Pan Head Machine Screws II
II
Iwhile holding Lock Nuts GG
GG
Gwith a 7/16 inch wrench and
tightening with a phillips screwdriver. Tighten each assembly securely.
33
33
3.Whenever you decide on another height position first remove the crib mattress. Remove Spring WW
WW
Wby detaching the spring from the Stabilizing Bars
VV
VV
Vby loosening and removing the (4) Lock Nuts GG
GG
Gand removing the (4) Pan Head Machine Screws II
II
I (installed in
22
22
2 above) by using a 7/16 inch wrench
and a phillips screwdriver. Carefully lift the spring from the crib. Make your selected height position change by following 11
11
1. of this Step. Then follow
22
22
2.to reinstall Spring WW
WW
W, again tighten all Pan Head Machine Screws securely as directed.
lowest position
middleposition
highest position
Long arm of
Scissor Arm
Assembly BB
BB
B
Short arm of
Scissor Arm
Assembly BB
BB
B
G
B
W
I
B
G
Stabilizer Bars VV
VV
V
with End Plates
MM
MM
M& NN
NN
Nattached
NOTE: CRIB IS DELETED FROM
DIAGRAM FOR CLARITY & DETAIL.

STEP 8-DIAGRAM 8: DRAWER BUILD-UP&INSTALLATION Installation of Mini Blocs EE
EE
E.Refer to Diagrams 8A8A
8A8A
8A, 8B8B
8B8B
8B, 8C8C
8C8C
8C,
8D8D
8D8D
8D, and 8E8E
8E8E
8E. Install (1) Mini Bloc EE
EE
Einto each of the Drawer Ends bb
bb
bas
7
LH02704:04/00LH02704:04/00
LH02704:04/00LH02704:04/00
LH02704:04/00
shown in Diagram 8A8A
8A8A
8A.NOTE: Before installing the Mini Blocs EE
EE
E, be sure that you have the (2) Drawer Ends bb
bb
baligned exactly as shown in Diagram
8A8A
8A8A
8A in order to have a pair when complete.
Build Up of the Drawer. Assemble the Drawer as shown in Diagram 8E8E
8E8E
8E. NOTE: After the drawer is assembled as shown in Diagram 8E8E
8E8E
8E,turn
the drawer upside down and install (2) 5/8" P/H Slotted/Phillips Screws OO
OO
Ointo holes located in Drawer Bottom ff
ff
fto secure it to the Drawer Partition
cc
cc
c.
Drawer Installation. Install the Drawer under the crib by inserting the rollers on Drawer Rails gg
gg
gand hh
hh
h (attached to the drawer) into the channel of
Drawer “Cabinet Rails” ii
ii
iand jmounted to Headboard AAAA
AAAA
AA and Footboard ZZ
ZZ
Zunder the crib.
If the drawer fits too loose in its tracks, you can adjust the fit by adding the enclosed washers Tas shown in Diagram 3. Remove the drawer. Carefully
lay the crib on its back to allow access to parts RR
RR
R, ii
ii
i& aa
aa
a. Remove the Drawer Rails and insert a washer over each screw point RR
RR
Rbetween aa
aa
a
and ZZ
ZZ
Zand/or AAAA
AAAA
AA. Reinstall rail assembly and drawer. Add additional washers if necessary repeating this process.
Insure the washers are installed between parts
aa
aa
a and
ZZ
ZZ
Z and/or
AAAA
AAAA
AA only if needed.
8E
8D
8C
8B
8A
Tighten the screw in Mini
Block Eto thread into
prebored pilot holes in
Drawer Front d.
Attach Drawer Rail-Left hto
Drawer End bin the same man-
ner as shown for opposite end -
NOTE: Both Roller Wheels will go
toward Drawer Back e.
Install extra screws Fat
these locations.
F
Install in prebored pilot holes
on both Drawer Ends b.
Insert Drawer Bottom finto
groove on all 4 sides.
See 8B for
close-up view
See 8D for
close-up view
Drawer
Bottom
Grooves
Drawer
Bottom
Groove
NOTE: With the drawer bottom grooves
together - will result in a pair.
Roller
Wheel
Laminated edge
g
b
E
f
ce
d
K
b
E
c
E
E
d
b
E
bE
b

Locate the (4) Casters HH
HH
H, insert one into socket in each lower
corner post of Headboard AAAA
AAAA
AA and Footboard ZZ
ZZ
Z. Caster HH
HH
H
design may vary according to your particular model. CAUTION:
If crib is placed on exceptionally thick carpet, take care when crib
is rolled as Casters HH
HH
H could catch on thick carpet pile and possibly
cause breakage to lower corner posts of crib.
Place a purchased mattress on Spring WW
WW
Wand crib is ready for use.
After completing crib assembly, and after making yourself aware
of the Warnings, Cautions, Cleaning, Storage, Use and
Maintenance of crib, store the assembly directions in the plastic
pouch which was pre-attached to Spring WW
WW
W. For future referral
to assembly directions you will only need to remove them from the
plastic pouch. We caution you not to store excess hardware in
plastic pouch as this would be a danger to child if retrieved by him/
her.
You have the option to convert the crib to a Daybed for additional
years of use by your child. Follow directions for converting this
crib to a Daybed when your child outgrows his/her use of the crib.
STEP9:FINISHING TOUCHES.
A SSEMBLY D IRECTIONS TO C ONVERT C RIB TO A D AYBED .
Refer to Sketch A .Follow
Installation of Dropside di-
rections, (STEP 6), in re-
verse order for the re-
moval of Dropside XX
XX
X us-
ing extreme caution when
doing so to avoid damage
to the finish of your crib/
daybed. Remove Upper
Guide Bushings and
Lower Guide Pins as
shown in Step 3 , in re-
verse order (NOTE: it is
very important that the
Lower Guide Pin DD
DD
Dis
removed and stored
away from the child be-
cause it is not attached
to the crib, and if removed by the child and swallowed, Lower Guide Pin DD
DD
D
could be a choking hazard). Store removed Dropside XX
XX
Xand hardware so you will
be able to reassemble into a crib if you wish to do so in the future. Only use the lowest
position placement of Spring WW
WW
W when using as a Daybed, (refer to Step 7) . Periodically
check and tighten all fastening devices (screws and bolts) if needed. Return the
assembly directions to the plastic pouch attached to the crib spring for future
availability.
LH02704:04/00LH02704:04/00
LH02704:04/00LH02704:04/00
LH02704:04/008
Sketch A
(style may vary)
•MAINTENANCEOFYOURLEGACYCRIB: Uponcompletionofassemblybesurescrewsandbolts(fasteningdevices)aretightenedsecurely.Aperiodic
check should be made of fastening devices and tighten if needed. Before each usage or assembly, inspect crib for damaged hardware, loose joints,
missing parts or sharp edges. DO NOT use crib if parts are missing or broken. Ask your Dealer or LEGACY (812/ 883-3111), http://
www.childcraftind.com for replacement parts and instructional literature if needed. Include Model Identification Number with your request which you
recorded on page 1. DO NOT substitute parts. DO NOT make any alteration to this crib.
• CLEANINGINSTRUCTIONSFORYOURLEGACYCRIB: Mixtogetheramildsolutionofgentledishwashingliquidandwater,applytocribsurfaceusing
a soft clean cloth lightly dampened in the solution. Rinse with clear water again using a soft clean cloth then dry all surfaces thoroughly with a soft dry
cloth.NOABRASIVECLEANERS,SCOURINGPADS,STEELWOOL,ORCOARSERAGSSHOULDBEUSEDTOCLEANTHISFINEFURNITURE.
• STORAGEANDUSEOFYOURLEGACYCRIB: Aprintedplasticpouchisattachedtothecribspringforthepermanentstorageoftheassemblydirections.
After completing the assembly process you are advised to read and be aware of all WARNINGS, CAUTIONS, CLEANING, STORAGE, USE AND
MAINTENANCEnoticescontained inthissetofassemblydirectionsandprintedontheplasticpouchattached tocribspring.Youwill then placethecomplete
set of assembly directions into the plastic pouch for future referral. We caution you not to place excess hardware in the plastic pouch as it could present
danger to a child if retrieved and it could also puncture crib mattress. When storing crib use CAUTION as extreme temperature or humidity changes could
be harmful. Use CAUTION when a vaporizer is in use, always aim vapor stream away from crib as well as away from any other wood furniture item.
PurchasedMattress
(See size requirements
under CAUTION on page 9)
b
b
dcf
H
H
Z
Y
AA
X

ΦΦ
ΦΦ
ΦFAILURE TO FOLLOW THESE WARNINGS AND ASSEMBLY INSTRUCTIONS COULD RESULT
IN SERIOUS INJURY OR DEATH.
ΦΦ
ΦΦ
ΦREAD ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP INSTRUCTIONS FOR
FUTURE USE.A plasticpouchisattachedtocribspringforpermanentstorageoftheinstructional
literature.
ΦΦ
ΦΦ
ΦBEFORE EACH USAGE OR ASSEMBLY, INSPECT CRIB FOR DAMAGED HARDWARE, LOOSE
JOINTS,MISSINGPARTSORSHARPEDGES.DONOTUSECRIBIFANYPARTSAREMISSINGOR
BROKEN. ASK YOUR DEALER OR LEGACY, P.O. BOX 444, SALEM, IN 47167-0444 USA (812/883-
3111), http://www.childcraftind.com FOR REPLACEMENT PARTS AND INSTRUCTIONAL LIT-
ERATURE IF NEEDED. INCLUDE MODEL IDENTIFICATION NUMBERS WITH YOUR REQUEST
WHICH YOU RECORDED ON PAGE one. DO NOT SUBSTITUTE PARTS.
ΦΦ
ΦΦ
ΦAFTER RAISING SIDE, MAKE SURE LATCHES ARE SECURE.
ΦΦ
ΦΦ
ΦWHENCHILDIS ABLE TO CLIMB OUTORREACHES THE HEIGHT OF 35INCHES(90 CENTIME-
TERS) THE CRIB SHALL NO LONGER BE USED.
ΦΦ
ΦΦ
ΦDO NOT PLACE CRIB NEAR WINDOW WHERE CORDS FROM BLINDS OR DRAPES MAY
STRANGLE A CHILD.
ΦΦ
ΦΦ
ΦIF REFINISHING, USE A NONTOXIC FINISH SPECIFIED FOR CHILDREN'S PRODUCTS.
ΦΦ
ΦΦ
ΦDO NOT LEAVE CHILD IN CRIB WITH SIDE LOWERED. BE SURE SIDE IS IN RAISED AND
LOCKED POSITION WHENEVER CHILD IS IN CRIB.
ΦΦ
ΦΦ
ΦWHEN CHILD IS ABLE TO PULL TO STANDING POSITION, SET MATTRESS TO LOWEST
POSITION AND REMOVE BUMPER PADS, LARGE TOYS AND OTHER OBJECTS THAT COULD
SERVE AS STEPS FOR CLIMBING OUT.
ΦΦ
ΦΦ
ΦNEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC FILM AS MATTRESS COVERS
BECAUSE THEY CAN CAUSE SUFFOCATION.
ΦΦ
ΦΦ
ΦDO NOT USE A WATER MATTRESS WITH THIS CRIB.
ΦΦ
ΦΦ
ΦREPLACE TEETHING RAIL(S) IF DAMAGED OR LOOSE (IF EQUIPPED WITH TEETHING RAIL).
ΦΦ
ΦΦ
ΦSTRINGS CAN CAUSE STRANGULATION! DO NOT PLACE ITEMS WITH A STRING AROUND A
CHILD'S NECK, SUCH AS HOOD STRINGS OR PACIFIER CORDS. DO NOT SUSPEND STRINGS
OVER A CRIB OR ATTACH STRINGS TO TOYS.
ΦΦ
ΦΦ
ΦREMOVE ALL CRIB TOYS WHICH ARE STRUNG ACROSS CRIB AREA WHEN YOUR CHILD IS
BEGINNING TO PUSH UP ON HANDS AND KNEES OR IS 5 MONTHS OF AGE, WHICHEVER
OCCURS EARLIEST. THESE TOYS CAN CAUSE STRANGULATION!
ΦΦ
ΦΦ
ΦWHEN DISASSEMBLING THIS CRIB, DO NOT REMOVE ANY ITEM ATTACHED WITH WOOD
SCREWS.
ΦΦ
ΦΦ
ΦALWAYS ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY CHECKING REGULARLY,
BEFORE PLACING THE CHILD IN THE CRIB, THAT EVERY COMPONENT IS PROPERLY AND
SECURELY IN PLACE.
WW
WW
WARNINGARNING
ARNINGARNING
ARNING
CACA
CACA
CAUTIONUTION
UTIONUTION
UTION JCHE LH02704:04/00.p65
CHILDCRAFTINDUSTRIES,INC.
P.0.Box444,Salem,IN USA 47167-0444
•PH-812/883-3111 •FAX-812-883-1819
http://www.childcraftind.com
ENGLISH
MADE IN USA
ΦΦ
ΦΦ
ΦANY MATTRESS USED IN THIS CRIB MUST BE AT LEAST 27-1/4
INCHES(69CENTIMETERS),BY51-5/8INCHES(131CENTIMETERS),
WITHATHICKNESSNOTEXCEEDING6INCHES(15CENTIMETERS).
The dimensions of the mattress shall be taken from seam to seam
or edge to edge where appropriate.
ΦΦ
ΦΦ
ΦUPON COMPLETION OF ASSEMBLY BE SURE ALL SCREWS,
BOLTS AND FASTENING DEVICES HAVE BEEN TIGHTENED SE-
CURELY.AFREQUENTCHECKSHOULDBEMADEOFALLSCREWS,
BOLTSANDFASTENINGDEVICESANDTIGHTENIFNEEDED.
LH02704:04/00LH02704:04/00
LH02704:04/00LH02704:04/00
LH02704:04/00 9
▲
!