Lepro PR906501-US User manual

Floodlight Camera
User Manual

Package Contents
Introduction
Installation Guide
APP Pairing
APP Using
Troubleshooting
4
5
6
12
16
20
English

Contenu
Introduction
Guide d'installation
Couplage avec APP
Utilisation de l’APP
Astuces de dépannage
22
23
24
30
34
38
Français

Package Contents
Floodlight Camera
D: Grounding screw(Green) x 1
A: Crossbar x 1 B: EVA Gasket x 1
C: Screw x 2
E: Nut x 1 F: Wire Nuts x 3
User Manual
28 W(Lamp 22W / Camera 6W), 2400 lm, 110-130V ~, 60 Hz, 0.235 A,
CRI>70, PF 0.6, IP65, 5000 K, -25 °C – 40 °C / -13 °F - 113 °F
Model No.: PR906501-US
EN

This Floodlight Camera is a sophisticated smart home security system combin-
ing advanced PIR motion sensor lighting and real-time video monitoring. It can
help monitor and keep an eye on your home day and night. It will alert you the
minute someone enters your property, including an intruder, and allows you to
talk to them right away.
Introduction
LED Light
Installation Base
1080P Camera
PIR Sensor
MIC
Reset button
and TF Slot inside
Notice:
• Do not dismantle or replace any parts of the product without professional
guidance.
• This manual is meant for informational purposes only. Working with electrici-
ty can be dangerous unless you take precautionary safety measures.
• We recommend you consult and hire a licensed electrician.
(TF card Max.128 G
and Not included)
EN

RECOMMENDED INSTALLATION HEIGHT: 6.5-8.25 feet above the ground.
At a detection angle of 75°, the sensor will provide a maximum sensing range
of up to 39 feet.
Installation Guide
6.5 ft. Motion Sensor
Downward 5°
Detection Coverage 39 ft
39 ft
Height
8.25 ft.
Motion Sensor
Downward 10°
Detection Coverage
Height
You can adjust and move the sensor heads up and down, left to right, to the
required angle for the desired coverage area.
EN

TOOLS YOU NEED (not included)
Notice:
To attain maximum product performance and avoid unnecessary environmental
disturbance, please be sure to comply with the following conditions during
product installation:
• Do not install the product in close proximity to thermal sources, like air
conditioner outdoor unit or kitchen smoke outlet, etc.
• Make sure there are no reflective objects within a 5 feet range of the PIR
sensor, which will interfere with the sensor’s normal functioning.
• Do not put the camera directly facing high PF LED light, which will pick up the
flickering of the LEDs
CAUTION: PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN !
Flathead Screwdriver Screwdriver Silicone Sealant
Step Ladder Protective Eye Wear Pliers
EN

You can install the Floodlight Camera by following the steps below:
Step 1: Shut the power off at the circuit breaker (NOT THE SWITCH).
Notice:
• Please make sure the power voltage is 110-130 V~, 60 Hz.
• Properly ground the fixture.
• Do not connect this light fixture to a dimmer switch or timer.
• Always follow the code standards when installing wired connections.
• Do not install near combustible or flammable surfaces.
Step 2: Install the Mounting Crossbar
Attach the crossbar (A) onto the junction box (not included) using the two long
screws (C) included in the package. Ensure that the screw thread on the center
hole is pointing away from the surface.
Notice: The Floodlight Camera must be installed on a wall and the UL-listed
junction box.
WARNING:
Risk of electrical shock!
Crossbar (A)
Screws (C) Screws (C)
ON
OFF
ON
OFF
OFF
EN

Step 3: Wiring the Floodlight Camera
Remove the paper barrier from the EVA gasket (B) and adhere the gasket to the
crossbar and outer edge of the round surface junction box. Ensure that the short
screw on the crossbar threads the hole of the EVA gasket(B).
Then wire as below:
a. Use a wire nut (F) to connect all the white wires. The white wire on Floodlight
Camera is neutral.
b. Use a wire nut (F) to connect all the black wires. The black wire on Floodlight
Camera is a hot wire.
c. Connect the ground wire from the junction box to the ground screw (D, green)
on the metal crossbar (A).
White (N)
Black (L) D
F
0.6”(15MM)
EN

Step 4: Mounting the Floodlight Camera
Make sure wire connections are secure.
Carefully align wires through the junction box.
Mount the Floodlight Camera onto the crossbar(A) and fasten with the supplied
Nuts(E). DO NOT over-tighten them.
Step 5: Restore power for the test
Restore power at the circuit breaker.
The Floodlight Camera will begin speaking to you to let you know it is in setup
mode. Now the Floodlight Camera is working!
ON
OFF
ON
OFF
ON
Ring (E)
E
EN