LF Illumination EF300 SERIES Service manual

EF300 SERIES TRIMMED
SIZE A RECESSED
INSTALLATION INSTRUCTIONS
* Risk of fire or electric shock.
* Disconnect all power before installing or servicing.
* Installation Instructions for qualified electricians only.
* Install per National Electrical Code and local regulations.
* Read Installation Instructions completely before installation.
* Failure to follow Installation Instructions may void warranties.
THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
C US
®
Warnings:
Integral Accessible
LED Driver
LED
Module
Suspension
Tie Down
Bracket
Ceiling
Material
Extruded Aluminum
Housing
Suspension &
Trim Strap
Extruded High Transmission
Acrylic Smooth Satin White Lens
Recessed Trimmed
Hanger Assembly
A
Extruded Aluminum
Fixture Housing
B
Optical Assembly
& Power Supply
C
Extruded Acrylic
Snap-in Lens
D
Aluminum
Spacer(s)
C
Hang 1/4-20 rod
or Wire Cable
Tie Down
A - SUSPENDED HANGER ASSEMBLY:
1. SUSPEND HANGER ASSEMBLY IN PLACE using 1/4-20 all thread or wire cable tie downs.
Suspension tie down bracket locations vary. Typically 6” from each end on each side of
housing.
2. When SETTING HANGER ASSEMBLY be sure that the top of the finished trim sets to the
bottom of the finished ceiling height. See Fig 1
B - EF300 HOUSING INSERT:
1. SLIDE FIXTURE HOUSING INTO HANGER ASSEMBLY and fasten into place using hardware
provided. Pre-set mounting locations match housing fastener strap. See Fig 1 .
2. P lace 6” aluminum spacers provided in mounting kit to ensure proper housing to lens width
when installing finished ceiling. The recommended placement of spacers is no more than four
feet apart.
C - OPTICAL ASSEMBLY AND POWER SUPPLY:
1. REMOVE APERTURE SPACERS, INSERT OPTICAL & POWER SUPPLY ASSEMBLY by inserting
up into the housing cavity. There is a tension clip on each side of driver housing, squeeze/com-
press and push up past inner housing tabs and release. This will lock assembly into place See
Fig 3 .
D - EXTRUDED ACRYLIC LENS:
1. REMOVE APERTURE SPACERS AND SNAP-IN LENS once all housing and inner components
have been set in place, wiring complete and mud-in finished. Gently push lens into housing until
formed tabs snap-in to place.
ASSEMBLY NOTE: The EF300 Recessed Series primarily consist of 4 major components
A, B, C, and D. See Fig. 2 & Fig. 3. This system is designed for ease of installation.
IT IS IMPORTANT TO READ INSTRUCTION SHEET COMPLETELY BEFORE INSTALLATION.
FIGURE 1
FIGURE 2
PAGE 1 OF 2
HEADQUARTERS
9200 Deering Avenue
Chatsworth CA 91311
Telephone: [phone]
Toll Free: 855-885-1335
Fax: [phone]
www.lfillumination.com
REV. 083116
©2016 LF ILLUMINATION LLC
We reserve the right to change or
withdraw specifications without prior notice.

Snap in lens
Locking
Joiners
Channel
Extend the alignment/locking
joiners mid way
Slide corresponding channels
together and fasten
1 2
AB
Optical
Fastening
Tension Clips
Wire Cable
Tie Down
Housing Fastener
Strap
Recessed Trimmed
Hanger Assembly
A
Extruded Aluminum
Fixture Housing
B
Optical Assembly
& Power Supply
C
Extruded Acrylic
Snap-in Lens
D
End Cap
* Risk of fire or electric shock.
* Disconnect all power before installing or servicing.
* Installation Instructions for qualified electricians only.
* Install per National Electrical Code and local regulations.
* Read Installation Instructions completely before installation.
* Failure to follow Installation Instructions may void warranties.
THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
C US
®
Warnings:
EXPLODED ASSEMBLY VIEW:
The EF300 Recessed Series primarily consist of 4 major
components A, B, C, and D. See Fig. 2 & Fig. 3. This system
is designed for ease of installation.
FOR ASSEMBLY SEQUENCE SEE PAGE ONE.
CONNECTING FOR CONTINUOUS RUNS: (Trim or Trimless)
Loosen and extend internal connecting joiners half way and lock in position.
Slide corresponding channel onto exposed joiner and lock into place.
See Fig. 4 steps 1 & 2.
PAGE 2 OF 2
FIGURE 3
FIGURE 4
NOTE: ALL WORK MUST BE
DONE WITH CIRCUIT OFF AND
COMPONENTS SHOULD NOT BE
INSTALLED WHEN FIXTURE IS
ENERGIZED.
EF300 SERIES
SIZE A RECESSED
INSTALLATION INSTRUCTIONS
HEADQUARTERS
9200 Deering Avenue
Chatsworth CA 91311
Telephone: [phone]
Toll Free: 855-885-1335
Fax: [phone]
www.lfillumination.com
REV. 083116
©2016 LF ILLUMINATION LLC
We reserve the right to change or
withdraw specifications without prior notice.