LG LS300N-D1 User manual

2
This lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
dangerous voltage within the product’s
enclosure that may be of sufficient magni-
tude to constitute arisk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and mainte-
nance (servicing) instructions in the litera-
ture accompanying the product.
FCC FCC WARNING: This equipment may generate or
use radio frequency energy.Changes or modifications
to this equipment may cause harmful interference
unless the modifications are expressly approved in the
instruction manual. The user could lose the authority
to operate this equipment if an unauthorized change
or modification is made.
REGULATORYINFORMATION: FCC Part 15
This equipment has been tested and found to comply
with the limits for aClass Adigital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful inter-
ference when the equipment is operated in acommer-
cial environment.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in aresidential area is
likely to cause harmful interference in which case the
user will be required to correct the interference at his
own expense.
Asuitable conduit entries, knock-outs or glands
shall be provided in the cable entries of this prod-
uct in the end user.
Caution: Danger of explosion if battery is incor-
rectly replaced. Replaced only with the same or
equivalent type recommended by the manufac-
turer.Dispose of used batteries according to the
manufacturer’s instructions.
CAUTION: TOREDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TOQUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK�
DO NOT�OPEN
Color Video Camera
Instruction Manual
Models :
Before installing, operating or adjusting this
product, please read this instruction booklet
carefully and completely.
LS300N-B1
LS300P-D1
LS300N-D1
LS300P-B1
LS300P-C1
•
•

3
4
Important Safety Instructions
Holes in metal, through which insulated wires
pass, shall have smooth well rounded surfaces or
shall be provided with brushings.
Warning: Do not install this equipment in aconfined
space�such as abookcase or similar unit.
Warning: Wiring methods shall be in accordance with
the�National Electric Code, ANSI/NFPA70.
Warning: This is aclass Aproduct. In adomestic
environment this product may cause radio interfer-
ence in which case the user may be required to take
adequate measures.
Caution: This installation should be made by aquali-
fied�service person and should conform to all local
codes.
Caution: Toavoid electrical shock, do not open the
cabinet.�Refer servicing to qualified personnel only.
Caution: The apparatus should not be exposed to
water�(dripping or splashing) and no objects filled
with�liquids, such as vases, should be placed on the
apparatus.
Disposal of your old appliance
1. When this crossed-out wheeled bin
symbol is attached to aproduct it means
the product is covered by the European
Directive 2002/96/EC.
2. All electrical and electronic products
should be disposed of separately from
municipal waste stream via designated
collection facilities appointed by the gov-
ernment or the local authorities.
3.The correct disposal of your old appliance
will help prevent potential negative conse-
quences for the environment and human
health.
4. For more detailed information about
disposal of your old appliance, please
contact your city office, waste disposal
service or the shop where you purchased
the product.
This product is manufactured to com-
ply with EMC Directive 2004/108/EC and
Low Voltage Directive 2006/95/EC.
European representative :
Todisconnect power from the mains, pull out the
mains cord plug. When install the product, ensure
that the plug is easily accessible. This class [A] digital apparatus complies with Canadian ICES-003
Get appareil numerique de la classe [A] est conforme a la norme
NMB-003 du canada
1. Read these instructions. -All these safety and
operating instructions should be read before the
product is operated.
2. Keep these instructions. -The safety,operating
and use instructions should be retained for future
reference.
3. Heed all warnings. -All warnings on the prod-
uct and in the operating instructions should be
adhered to.
4. Follow all instructions. -All operating and use
instructions should be followed.
5. Do not use this apparatus near water.-For
example: near abath tub, wash bowl, kitchen sink,
laundry tub, in awet basement; near aswimming
pool; etc.
6. Clean only with dry cloth. -Unplug this product
from the wall outlet before cleaning. Do not use
liquid cleaners.
7. Do not block any ventilation openings. Install
in accordance with the manufacturer's instruc-
tions. -Slots and openings in the cabinet are
provided for ventilation, to ensure reliable opera-
tion of the product, and to protect it from over-
heating. The openings should never be blocked
by placing the product on abed, sofa, rug or other
similar surface. This product should not be placed
in abuilt-in installation such as abookcase or
rack unless proper ventilation is provided and the
manufacturer’s instructions have been adhered to.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other appa-
ratus (including amplifiers) that produce heat.
Warning: To reduce a risk of fire or electric shock, doWarning: To reduce a risk of fire or electric shock, do
not expose this product to rain or moisture.not expose this product to rain or moisture.
•

5
Important Safety Instructions
6
Cautions for Safe Operation
9. Donotdefeatthesafetypurposeofthepolar-
izedorgrounding-typeplug.Apolarizedplug
hastwobladeswithonewiderthantheother.A
groundingtypeplughastwobladesandathird
groundingprong.Thewidebladeorthethird
prongareprovidedforyoursafety.Ifthepro-
videdplugdoesnotfitintoyouroutlet,consult
anelectricianforreplacementoftheobsolete
outlet.
10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specified by
the manufacturer.
12.Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer,or sold
with the apparatus. When acart is used, use
caution when moving the cart/apparatus com-
bination to avoid injury from tip-over.
Unplugthisapparatusduringlightningstormsor
whenunusedforlongperiodsoftime.
14.Referallservicingtoqualifiedserviceperson-
nel.Servicingisrequiredwhentheapparatus
hasbeendamagedinanyway,suchaspower-
supplycordorplugisdamaged,liquidhas
beenspilledorobjectshavefallenintothe
apparatus,theapparatushasbeenexposedto
rainormoisture,doesnotoperatenormally,or
hasbeendropped.
Power Supply
Handling of the unit
Be careful not to spill water or other liquids
on the unit. Be cautions not to get combustible
or metallic material inside the body. If used
with foreign matter inside, the camera is liable
to fail or to get a cause of fire or electric shock.
Operating and storage location
Avoid viewing a very bright object (such as
light fittings) during an extended period.
Avoid operating or storing the unit in the
following locations.
•Extremely hot or cold places (operating
temperature -10
o
C~50
o
C, however, we
recommend that the unit be used within a
temperature range of 0
o
C~45
o
C)
•Damp or dust place
•Places exposed to rain
•Places subject to strong vibration
•Close to generators of powerful
electromagnetic radiation such as radio or
TV transmitters.
13.
This camera must always be operated a AC 24V
or DC 12V or AC 230V Certified/Listed, class 2
power supply only.

7
Contents
8
Operating Controls and their Functions
Pin assignment of auto iris lens connector
Pin No. DC iris Video iris
1Damping - Vcc (+9V)
2Damping + Not used
3Drive + Video
4Drive - Ground
3
2
1
4
Tripod adapter
CCD cover
C/CS adjustment lever
Auto iris lens connector
OSD switch
Power LED
BNC connector for video output
Lens selection switch
Power input connector
1
2
3
4
5
6
7
8
9
AUTO IRIS
Models
Models Signal System Power
LS300N-D1
LS300P-D1
LS300P-C1
LS300N-B1
LS300P-B1
NTSC
NTSC
PAL
PAL
PAL
DC 12V
DC 12V
AC 230V
DC 12V / AC 24V
DC 12V / AC 24V
1010
Power input terminal
1010
Cautions for Safe Operation ............................................................................... 6
Models ................................................................................................................ 7
Operating Controls and Their Functions .......................................................... 8-9
OSD Menu ................................................................................................... 10-25
AREA Setting ................................................................................................... 26
Specifications ............................................................................................... 27-28
LS300N(P)-D1 LS300N(P)-B1
LS300P-C1
VIDEO
OUT
DC ELC VIDEO
+ DC12V CLASS 2 ONLY
ㅡ
POWER VIDEO
OUT
DC ELC VIDEO
DC12V
AC24V
+ CLASS 2 ONLY
ㅡ
POWER
VIDEO
OUT
DC ELC VIDEO
POWER IN
AC230V
POWER

9
10
OSD MENU
Lens Mounting
CAUTION
Auto Iris Mode Selection
POWER VIDEO
OUT
DC ELC VIDEO
DC 12V
+
1. Loosen the C/CS adjustment lever
2. Hold up the lever to change the mount to CS / Hold down the
lever to change the mount to C
3. Tighten the C/CS adjustmet lever
Be cautious not to use Auto Iris Lens with over 30mA.
DC iris level is preset in the factory. Only if necessary, adjust the DC
iris level to achieve the proper picture with AGC off.
DC ELC VIDEO
1. Set the auto iris mode selection switch to the position that
corresponds to the lens which is mounted to the camera.
Please refer to the table on the up.
2. OSD Setting : Refer to 12 page (OSD MENU - Lens)
DC
ELC
VIDEO
POSITION DC iris lens
Manual or fixed iris lens
Video iris lens
LENS
EXIT
LENS
SHUTTER
BLC
AGC
WHITE BAL.
FUNCTION
DC / VIDEO / MANUAL
AUTO (0~255 steps) / FLK / FIXED (1/60-1/50 ~1/100,000 sec) / MANUAL (0~255 steps)
ON / OFF
ON / OFF
ATW / AWB / FIXED / MANUAL
CAMERA ID
MIRROR
DAY & NIGHT
MOTION
PRIVACY
GAMMA
LANGUAGE
ON / OFF
ON / OFF
AUTO / COLOR / BW
ON / OFF
ON / OFF
0.05 ~ 1.00 / USER
CONTRAST / SHARPNESS / CB_GAIN / CR_GAIN
C/CS adjustment leverC/CS adjustment lever
ADJUST
RESET
ENGLISH / KOREAN / CHINESE1(SC) / CHINESE2(DC) / JAPANESE

11
OSD MENU - Setting
12
OSD MENU - LENS
POWER VIDEO
OUT
DC ELC VIDEO
DC 12V
+
UP BUTTON
DOWN BUTTON
LEFT BUTTON
RIGHT BUTTON
SETUP
SETUP
LENS
SHUTTER
BLC
AGC
WHITE BAL.
FUNCTION
ADJUST
EXIT
DC
FIXED
OFF
ON
AWB
1
23
4
Settings can be made using the 5 buttons
located on the back of the camera.
1. Please press the SETUP button.
- Settings can now be made.
The SETUP menu is displayed on the monitor.
2. Please select any function you wish to activate
by using the UP and DOWN buttons.
3. Please press the LEFT or RIGHT button if you
wish to change mode.
4. Please select 'EXIT' and then press the SETUP
button to finish the setting.
LENS DC
BRIGHTNESS
: RETURN
200
Please select the type of the lens you wish to use by pressing the LEFT or
RIGHT button.
* When using an auto iris lens, the setting of the auto iris lens selection switch, located on the
back of the camera, must be on DC or ELC or VIDEO depending on the type of the lens which is
being used.
• DC/VIDEO : Auto iris lens selection
• MANUAL : Manual lens selection
• DC mode - Brightness setting(0~255 steps)
SETUP
LENS
SHUTTER
BLC
AGC
WHITE BAL.
FUNCTION
ADJUST
EXIT
DC
FIXED
OFF
ON
AWB
* When it is ‘RESET’ , ‘LENS’ comes to be initialized to ‘DC’ .

13
OSD MENU - SHUTTER
14
OSD MENU - BLC(Backlight compensation)
Please select the shutter mode by pressing the LEFT or RIGHT button.
• AUTO : Please select ‘AUTO’ and then press the SETUP
button to ‘AUTO’ the setting.
Auto Control of the shutter speed can be achieved.
Adjust range : 0 ~ 255 steps
• FLK : 'FLK' mode when flickering occurs on the screen,
due to an imbalance between illumination and
frequency.
- When selecting FLK mode, the shutter FIXED
mode is fixed at 1/100(1/120).
• FIXED : The shutter speed can be controlled manually.
Adjust range : 1/60 ~ 1/100,000 sec (NTSC)
1/50 ~ 1/100,000 sec (PAL)
• MANUAL : The shutter speed can be controlled manually.
Adjust range : 0(Shutter slow) ~ 255(Shutter fast) steps.
Please select the mode you wish to operate by pressing the LEFT or RIGHT button.
• ON : You can adjust the sensitivity and BLC area of backlight compensation.
When there is a strong backlight behind the object(within the BLC AREA),
Clear images of the object can still be obtained by using the BLC function.
• OFF : Backlight compensation function does not operate.
BLC ON
BLC AREA
BLC OFF
- When selecting DC/VIDEO lens, the shutter speed is ‘FIXED’ mode(1/60 or 1/50).
- When selecting MANUAL lens, the shutter speed is ‘AUTO’ mode.
* Please select ‘ON’ and the press the SETUP button to BLC the setting.
- BLC AREA : Please select all the area you wish to observe.
>Press the SETUP switch long. Enters with the set window. (Refer to 26 page : Area Setting.)
- BLC RATIO : The brightness can be adjusted level.
To control the brightness of the object ‘0(increase)’ to 63(decrease)’.
SETUP
LENS
SHUTTER
BLC
AGC
WHITE BAL.
FUNCTION
ADJUST
EXIT
DC
FIXED
ON
ON
AWB
SETUP
LENS
SHUTTER
BLC
AGC
WHITE BAL.
FUNCTION
ADJUST
EXIT
DC
FIXED
OFF
ON
AWB

15
OSD MENU - AGC(Auto Gain Control)
16
OSD MENU - WHITE BALANCE control
• The BRIGHTNESS can be adjusted within the range of 0 ~ 255 steps.
Please select the mode you wish to operate by pressing the LEFT or RIGHT button.
* If AGC OFF, DAY & NIGHT AUTO mode is not working.
- Refer to 19 page. (DAY & NIGHT setting)
AGC CONTROL
AGC GAIN
: RETURN
180
Please select the mode you wish to operate by pressing the LEFT or RIGHT button.
• ATW(Auto Tracking White Balance) :
This mode can be used out of the color temperature
range 2,500K ~ 9,500K
• AWB(Auto White Balance) :
This is a preset type function whereby white color in the
scene is detected and white balance is automatically
adjusted, then the setting status is stored.
This mode can be used within the color temperature
range 2,500K ~ 9,500K.
• FIXED :
WHITE BALANCE can be controlled manually.
Preset type - MODE1 : 2,500K(indoor)
• MANUAL :
This allows adjusting red and blue gain manually
according to requirements.
MODE2 : 3,200K(indoor)
MODE3 : 5,100K(outdoor)
MODE4 : 9,500K(outdoor)
SETUP
LENS
SHUTTER
BLC
AGC
WHITE BAL.
FUNCTION
ADJUST
EXIT
DC
FIXED
OFF
ON
AWB
SETUP
LENS
SHUTTER
BLC
AGC
WHITE BAL.
FUNCTION
ADJUST
EXIT
DC
FIXED
OFF
ON
AWB

17
OSD MENU - FUNCTION > ID Setup
18
OSD MENU - FUNCTION > MIRROR
1. Please position the highlight to point to 'FUNCTION' on the SETUP menu by
using the UP and DOWN buttons.
2. Please select the mode you wish to operate by pressing the UP or DOWN button.
ID SETUP
CAMERA ID
POSITION
RETURN
C
CAM 01
CAMERA ID
• ON : Set a horizontal image inversion.
• OFF : Cancels the inversion.
MIRROR OFF
MIRROR ON
If you press the SETUP button after moving cursor to 'C', all the letters will be erased.
Using the MENU key to set character postion.
FUNCTION
CAMERA ID
MIRROR
DAY NIGHT
MOTION
PRIVACY
GAMMA
LANGUAGE
RESET
RETURN
OFF
ON
AUTO
OFF
OFF
0.45
ENGLISH
FUNCTION
CAMERA ID
MIRROR
DAY NIGHT
MOTION
PRIVACY
GAMMA
LANGUAGE
RESET
RETURN
ON
OFF
AUTO
OFF
OFF
0.45
ENGLISH

19
OSD MENU - FUNCTION > DAY & NIGHT
20
Please select the mode you wish to operate by pressing the LEFT or RIGHT button.
OSD MENU - FUNCTION > DAY & NIGHT
• AUTO : The camera selects black and white mode.
If the picture is dark, on color mode if the picture is
bright enough.
Please select 'AUTO' and then press the SETUP
button to DAY&NIGHT setting.
- DELAY : Delay time when the DAY&NIGHT function starts or stops.
(0~63 sec)
- START LEVEL : Set the brightness level where the DAY&NIGHT start to
operate. 0(high light)~255(low light)
- END LEVEL : Set the brightness level where the DAY&NIGHT function
stop operating. 0(high light)~255(low light)
※Operating Conditions
1) Due to the connection with the value of AGC, it doesn't work when "AGC OFF".
2) Delay time shall be more than 1sec.(at least).
(with the value "0", it is in "DAY MODE" continuously.)
3) Because a start level is connected with the value of AGC, A start level shall be set less
than the value of AGC.
4) A start level shall be higher than an end level.
• COLOR : Color mode enabled.
• B / W : Black and White mode enabled.
Please select 'B/W' and then press the SETUP
button to BURST the setting.
- BURST ON : BURST signal 'ON'
- BURST OFF : BURST signal 'OFF'
FUNCTION
CAMERA ID
MIRROR
DAY NIGHT
MOTION
PRIVACY
GAMMA
LANGUAGE
RESET
RETURN
OFF
OFF
AUTO
OFF
OFF
0.45
ENGLISH

21
OSD MENU - FUNCTION > PRIVACY
22
This modes conceals the areas you do not wish to appear on the screen.
• OFF : Cancels the PRIVACY mode.
• ON : Operates the PRIVACY mode.
PRIVACY ZONE
OSD MENU - FUNCTION > Motion Detection
Please select the area you wish to observe from the 64 areas in Area selection
mode.
• OFF : MOTION DETECTION mode is cancelled.
• ON : Any motion in the selected areas is observed.
Please select 'ON' and then press the SETUP
button to MOTION the setting.
- AREA : Set the MOTION area.
> Press the SETUP switch long. Enters with the set window.
(Refer to 26 page : Area Setting.)
- MOTION TH : High luminous motion theshold value
To control the MOTION TH.
‘0(sensitivity)’ to ‘255(insensitivity)’
- MOTION TRACE : ON - MOTION TRACE 'ON'
OFF - MOTION TRACE 'OFF'
Motion Detection
Motion ICON
* Please select 'ON' and then press the SETUP button * Please select 'ON' and then press the SETUP button
to PRIVACY the setting. to PRIVACY the setting.
- Select an area to mask from the 4 areas in AREA SEL
- Change the AREA STATE of the selected area to 'ON'
- From COLOR, press the Left/Right buttons to control the color.
- Set the area size from the LEFT/RIGHT/TOP/BOTTOM menu,
and then press the SETUP button.
FUNCTION
CAMERA ID
MIRROR
DAY NIGHT
MOTION
PRIVACY
GAMMA
LANGUAGE
RESET
RETURN
OFF
OFF
AUTO
OFF
ON
0.45
ENGLISH
FUNCTION
CAMERA ID
MIRROR
DAY NIGHT
MOTION
PRIVACY
GAMMA
LANGUAGE
RESET
RETURN
OFF
OFF
AUTO
ON
OFF
0.45
ENGLISH

OSD MENU - FUNCTION > GAMMA
23
24
FUNCTION
CAMERA ID
MIRROR
DAY NIGHT
MOTION
PRIVACY
GAMMA
LANGUAGE
RESET
RETURN
OFF
OFF
AUTO
OFF
OFF
0.45
ENGLISH
Select a GAMMA value.
• Select [GAMMA] option on the [FUNCTION] screen.
• Press LEFT or RIGHT button to select a GAMMA.
To control the brightness,
'0.05(increase)' to '1.00(decrease), USER'
OSD MENU - FUNCTION > LANGUAGE
FUNCTION
CAMERA ID
MIRROR
DAY NIGHT
MOTION
PRIVACY
GAMMA
LANGUAGE
RESET
RETURN
OFF
OFF
AUTO
OFF
OFF
0.45
ENGLISH
Select a LANGUAGE for the setup menu and
on-screen display.
• Select [LANGUAGE] option on the [FUNCTION]
screen.
• Press LEFT or RIGHT button to select a LANGU-
AGE.
- ENGLISH
- KOREAN
- CHINESE1(SC)
- CHINESE2(DC)
- JAPANESE

OSD MENU - ADJUST
25
26
• CONTRAST : The CONTRAST can be adjusted within the value of 0~255 steps.
• SHARPNESS : The outline of the video image becomes cleaner and more distinctive as the level of
SHARPNESS increases. If the level goes up excessively.
However, it may affect the video image and generate noise. (0~31 steps)
• CB_GAIN : Obtains the optimum amount of blue gain. (0~255 steps)
• CR_GAIN : Obtains the optimum amount of red gain. (0~255 steps)
- If the level goes up excessively, It may affect the video image and generate noise.
ADJUST
CONTRAST
SHARPNESS
CB_GAIN
CR_GAIN
67
16
224
224
SETUP
LENS
SHUTTER
BLC
AGC
WHITE BAL.
FUNCTION
ADJUST
EXIT
DC
FIXED
OFF
ON
AWB
AREA Setting
ALL CLEAR
ALL SET
RETURN
Cursor : Please select area.
- Yellow color is the selected area.
- Orange color is the nonselected area.
*Press the SETUP switch long. Enter with the sub set menu.
All CLEAR : Cancel the all selected area.
ALL SET : select all the area.
RETURN : Using the ‘RETURN’ key to go back to the main menu.
11
11
22
22
33
33
44
44

28
27
1/3-Inch interline Color CCD (Super HAD)
C/CS Mount
Digital Signal Process
2 : 1 Inerlace
Automatic Internal
More than 520 TVLine(H)
More than 50dB
2,000Lux (3,200K)
0.4 Lux (F1.0)
1Vp-p Composite (75Ω)
ATW / AWB / Fixed / Manual
ON / OFF
ON / OFF
AUTO / COLOR / BW
ON / OFF (64 Area)
ON / OFF (4 Zone)
ON / OFF
DC12V / AC 24V
2.5W
-10℃ ~ +50℃ (Humidity : 0%RH ~ 60%RH)
-20℃ ~ +60℃ (Humidity : 0%RH ~ 85%RH)
Approximately 420g
55(H) x 68(V) x 121.7(D)
LS300N-B1 LS300P-B1 LS300P-C1
Specification
Signal System
Total/Effective Pixelsg
Pick-Up Device
Lens
Signal Process
Scanning System
Sync. System
Scanning Frequency
Resolution
S/N Ratio
Standard Illuminance
Sensitivity(1/3 output)
Video Output Signal
White Balance
Gain Control
Backlight Compensation
DAY & NIGHT
Electronic Shutter Speed
Motion Detection
Privacy Mask
Mirror
Power Source
Power Consumption
Operation Temp.
Storage Temp.
Weight
Dimensions
OSD
NTSC PAL
410K / 380K 470K / 440K
1/3-Inch interline Color CCD (Super HAD)
C/CS Mount
Digital Signal Process
2 : 1 Inerlace
Automatic Internal
59.94 Hz(VD) 50 Hz(VD)
More than 520 TVLine(H)
More than 50dB
2,000Lux (3,200K)
0.4 Lux (F1.0)
1Vp-p Composite (75Ω)
ATW / AWB / Fixed / Manual
ON / OFF
ON / OFF
AUTO / COLOR / BW
AUTO / FIXED(1/60 ~ 1/100,000sec) / AUTO / FIXED(1/50 ~ 1/100,000sec) /
MANUAL(256 steps) / Flickerless MANUAL(256 steps) / Flickerless
ON / OFF (64 Area)
ON / OFF (4 Zone)
ON / OFF
DC12V
2.9W
-10℃ ~ +50℃ (Humidity : 0%RH ~ 60%RH)
-20℃ ~ +60℃ (Humidity : 0%RH ~ 85%RH)
Approximately 330g
55(H) x 68(V) x 121.7(D)
Model LS300N-D1 LS300P-D1
NTSC PAL
410K / 380K 470K / 440K
PAL
470K / 440K
AUTO / FIXED(1/60 ~ 1/100,000sec) / AUTO / FIXED(1/50 ~ 1/100,000sec) /
MANUAL(256 steps) / Flickerless MANUAL(256 steps) / Flickerless
59.94 Hz(VD) 50 Hz(VD) 50 Hz(VD)
AUTO / FIXED(1/50 ~ 1/100,000sec) /
MANUAL(256 steps) / Flickerless
AC 230V
2.5W
Approximately 420g Approximately 500g

P/NO : MFL61949101