Libify GC5 User manual

LIBIFY® GC5
Instruction manual
Enterprise

GEOCARE® 3 GEOCARE®
2
OVERVIEW
GEOCARE® is a mobile emergency call system that can trigger an
emergency call virtually anywhere and at any time.
Pressing the SOS key for three seconds establishes a telephone
connection to an emergency contact(1). The emergency contact
can be an emergency call center or a contact person (e.g. a care
giver). In parallel with the telephone call, the emergency contact
will be informed of your whereabouts via SMS(2).
The product package GEOCARE® with wireless transmitter and
active charging cradle can be used both as stationary and mobile
emergency call system. It makes it possible for the user to have
a more autonomous lifestyle. The user has more autonomy and
mobility as he/she knows that, in the event of an emergency,
quick and professional help is just a button press away.
GEOCARE® is compatible with all common emergency call monito-
ring centers and can therefore be connected to most operators.
1) A GSM wireless network must be available.
2) GPS reception must be available. If no GPS reception is available,
the most recent location with GPS reception is registered.
Congratulations
on your purchase of the GEOCARE® GC5
OVERVIEW

GEOCARE® 5 GEOCARE®
4
OVERVIEW
Device description GEOCARE®
1On/off key
2SOS key
3Microphone
4Speaker
1
2
3
4
Device description Active charging cradle
1SOS key
2Day-care-key
3Search-for-GEOCARE-key
4Speaker
5Microphone
1
2
3
4
5
5 6 7
5Network status
6Service
7Battery status

GEOCARE® 7 GEOCARE®
6
OVERVIEW
Device description Wireless transmitter
1SOS key
2Strap closure
3Wristband
4Status indicator LED
1
2
3
4
1. Switch device on and off:
Keep the on/off key 1pressed for
at least 3 seconds until the on/off
key slowly flashes a white light. The
device is ready for operation when
network status indicator shines
in green
2. Trigger emergency call:
Keep the SOS key 2pressed for
approx. 3 seconds until an audible
signal is emitted and the SOS key
flashes red light.
3. Cancel emergency call:
Press the SOS key 2for approx.
10 seconds until an audible signal
is emitted and the SOS key no
longer flashes red light.
Brief description GEOCARE®
10 Sec
3 Sek
3 Sek

GEOCARE® 9 GEOCARE®
8
OVERVIEW
Scope of delivery
The delivered GEOCARE® package contains
the following components:
• GEOCARE®
• Active charging cradle
• Wireless transmitter with wristband and necklace
• AC adapter with USB-Cable
Software and manual
The Software for the configuration of GEOCARE®
and the appropriate manual are available online at
following internet address:
www.libify.com/GEOCARE-GC5

GEOCARE® 11 GEOCARE®
10
Table of contents
OVERVIEW
Device description GEOCARE®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.4
Device description Active charging cradle . . . . . . . . . . . . . . . . . . . . . . . . . .S.5
Device description Wireless transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.6
Brief description GEOCARE® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.7
Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.8
Software and manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.9
Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.10
Charging the battery/battery life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.12
Switching on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.13
Installing the software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.14
Configuring GEOCARE®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.15
INSTALLATION
Permissions for notification profiles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.21
Notes on „general settings“ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.24
Alarm settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.28
Zone Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.30
SIM card settings: PIN, APN and AGPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.32
GEOCARE® Hardware/status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.33
Top menu bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.34
USAGE
Wireless transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.36
First use of the wireless transmitter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.37
Remodelling instructions for the wireless transmitter / radiobutton . . . . . . . . . .S.40
To wear the radiobutton, you have two alternatives: . . . . . . . . . . . . . . . . . . . .S.40
Wearing the radiobutton as a wristwatch . . . . . . . . . . . . . . . . . . . . . . . . . . .S.40
Wearing the radiobutton as a necklace. . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.43
Active charging cradle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.46
First use of the Active charging cradle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.48
Operating GEOCARE®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.51
SMS commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.53
GEOCARE™ mobile App
for Android phones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.55
Setting up the GEOCARE® Portal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.57
Room monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.60
INDICATIONS
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.61
Wireless transmitter‘s battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.62
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.63
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.67
Technical data - GEOCARE® GC5 (1/3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.69
Technical data - GEOCARE® GC5 (2/3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.70
Technical data - GEOCARE® GC5 (3/3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.71
Technical data - Wireless transmitter RB3 . . . . . . . . . . . . . . . . . . . . . . . . . . .S.72
Technical data - Active charging cradle AC3 . . . . . . . . . . . . . . . . . . . . . . . . . .S.73
Warning notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.74
For Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.75
Operation – Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.80
LED indicators – Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.80
EU declaration of conformity
GEOCARE® GC5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.84
EU declaration of conformity
radiobutton. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.85
EU declaration of conformity
Active charging cradle AC3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.87
Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .S.89
OVERVIEW INSTALLATION USAGE INDICATIONS

GEOCARE® 13 GEOCARE®
12
OVERVIEW
Charging the battery/battery life
Connect the USB connector of the charging cradle to the supplied
charger adapter. Fit the required AC plug (EU or UK)* and connect
it to the power supply.
Place the GEOCARE® in the charging cradle. The GEOCARE® must be
charged before it is used for the first time. The duration for a com-
plete charge is approx. 3 hours.
The typical battery lifetime is 30 hours. When only 20% of this life-
time is remaining, GEOCARE® emits an audible sound. From the
moment when only 10% of the battery lifetime is remaining, an
audible sound is emitted periodically every 15 minutes. Beside the
audible sounds signaling low battery when its remaining lifetime
is 20%, 10% and 0%, a notification is sent to the configured emer-
gency contact by SMS. After the first notification, the GEOCARE® is
still operational for 3 hours, depending on the configuration.
* The AC plug is attached to the bottom of the charging adapter (it is attached and then snapped
upwards and into place). To remove the AC plug, release the catch on the bottom of the charging adapter
(OPEN).
Caution: To save energy, the illumination for all keys is switched off one
minute after the device is last used. The illumination can be reactivated
by briefly pressing the SOS key.
Switching on and off
Switching on
To switch on GEOCARE®, hold the on/off key pressed for at least 3
seconds until the on/off key slowly flashes. Then release the on/
off key. At the end of this starting process a sound is emitted and
status lights show the operational readiness.
Alternatively, GEOCARE® will be switched on automatically when
the device is placed in the charging cradle. It then remains ready
for use until it is switched off. When GEOCARE® is in the charging
cradle, the on/off key lights up white.
Switching off
Preferably, you should always keep GEOCARE® switched on, so
that you can always trigger an emergency call and receive inco-
ming calls. The only time you have to switch off GEOCARE® is when
you have to enter an area where the usage of mobile phones is
dangerous or prohibited (e.g. on an aircraft). To do this, keep the
on/off key pressed for at least 3 seconds until it flashes a white
light. After a brief moment an audible sound is emitted. Then both
keys no longer light. GEOCARE® is switched off.

GEOCARE® 15 GEOCARE®
14
INSTALLATION
Installing the software
Your computer must have a USB port and be connected to Internet.
It should also have the operating system windows 7 or windows
10 installed on it.
Open your browser and enter the following address in the address
bar: www.libify.com/GEOCARE-GC5
Download the installation file for GC5. Start the installation with
a double click on the file. After the installation, you will find the
GEOCARE® Software in the installation directory you selected. You
also find a shortcut to this software on your desktop.
Connecting GEOCARE® to your computer
Switch on GEOCARE®. Connect the charging cradle to your PC using
the USB cable and place GEOCARE® in the charging cradle.
Starting the program
Start the software by double-clicking the program icon on your
computer.
INSTALLATION
Configuring GEOCARE®
PlugGEOCARE®inthechargingcradleandconnectthecradletoyour
computer via its USB cable. Wait until the On/Off key lights up white.
Start the software by double-clicking on the program symbol on
the desktop of your computer.
As soon as the program detects the plugged in GEOCARE®,
the corresponding field is highlighted in yellow in the de-
vice overview (Device Explorer). Select this field by dou-
ble-clicking on it – it will then be highlighted in blue.
By this doubleclick, the Configuration-/Statuswindow is opened.
Alternatively it can be opened from the menu „Edit Device“ in the
upper menu bar.
General settings
INSTALLATION

GEOCARE® 17 GEOCARE®
16
INSTALLATION
In the field „Owner“ of the configuration menu, you can edit indivi-
dual data of the GEOCARE®‘s user – e.g. Name, phone number as
well as relevant informations about the person.
In the menu „General Settings“, you can edit amongst others de-
vice language, time zone, map references, as well as distance for-
mats.
Settings for emergency calls
First of all, define the first emergency alarm receiver – It is only af-
ter doing this that you can use GEOCARE® as a mobile tracking- and
emergency call system.
Emergency contacts/notification points
It is imperative to set an emergency alarm receiver (Notification
point). Move the cursor to the first entry „not configured“ in the
menu „Alarm Receivers/Peer Notifications“. Select the type of pho-
ne connection from the drop down list in the middle. In the field on
the right next to the selection box, type the phone number using
the following format: Country code + phone number without lea-
ding zero e.g. [phone] („+49“ = country code for Germany).
Subsequently select a notification profile from the next selection
box. Notification profiles are explained in the following part.

GEOCARE® 19 GEOCARE®
18
INSTALLATION
Trusted monitor:
This is the highest privacy level („Trusted monintor“) – In the event
of an emergency, the set emergency alarm receiver is contacted
by a phone call as well as an SMS. This set alarm receiver also
receives all messages from GEOCARE® (including battery warning
messages, status messages and location data) and can actively
locate GEOCARE®.
Caution: You should only register highly trustworthy people
as „trusted monitors“!
Only receive emergency calls
(SMS and calls):
This emergency alarm receiver is informed with a phone call and a
notification by SMS. He/she does not receive any further notifica-
tions or permissions.
Only receive emergency calls
(voice connection only):
This emergency alarm receiver is informed with a phone call. He/
She receives no further permissions or notifications.
Gateway forwarding:
The messages from GEOCARE® are sent to an external gateway (such
as a rescue coordination center).
Follow the same procedure for each phone number that you wish to
assign. In the field „Info“, you can add a name or other information for
each phone number.
The priorities for the first four phone numbers are set in advance, ac-
cording to the order in which they were listed. The priority determines
the order in which the set phone numbers are informed about an
emergency situation.
The fields 5 and 6 for phone numbers are reserved for emergency
service operators. When needed, you can configure all settings indi-
vidually instead of using a predefined profile. You do this by clicking
on „More“.
Preferably you should save your changes as soon as you make
them. You save them by pressing the button „Save“ in top menu bar.
!Click with the cursor outside a field once before saving your settings.
This is imperative for the data you edited to be saved correctly.

GEOCARE® 21 GEOCARE®
20
INSTALLATION
GEOCARE®-Gateway
In the last assignable phone number position, you have the possibil-
ity to select the GEOCARE® gateway. Emergency call messages from
GEOCARE® are then also sent to the server. The emergency messages
can thereby be seen by the emergency alarm receiver on our online
portal (https://portal.geocare.de).
For more information, please refer to page 53.
Type of the SOS notification
SMS notification The emergency alarm receiver
(notification point) is informed by
text message (SMS).
Call notification The emergency alarm receiver
(notification point) is informed by
a phone call.
Permissions
Allow status messages The emergency alarm receiver
(notification point) is authorised
to query the device status (e.g.
battery level) and to receive other
status messages.
Permissions for notification profiles

GEOCARE® 23 GEOCARE®
22
INSTALLATION
Receive undefined
messages
The emergency alarm receiver
(notification point) is allowed to
receive messages that are for-
warded by GEOCARE® as undefined
messages. These may include
incoming SMS from unauthorised
third parties.
(e.g. information from the mobile
phone network etc.)
Allow system
configuration
The emergency alarm receiver
(notification point) is allowed to
change GEOCARE® configuration
settings via SMS — for example, the
time zone.
SMS-information
messages
The emergency alarm receiver
(notification point) is allowed to
receive information messages from
GEOCARE®. These may include mes-
sages when GEOCARE® is leaving
or returning to a particular defined
zone (e.g. HOME zone).
Allow SOS
confirmation
When this setting is active, the
SOS is confirmed in the event of an
emergency call when the phone
call is received.
If this setting is not selected, it
is imperative in the even of an
emergency call, to call back the
GEOCARE® or to confirm the SOS
with an SMS.
Gateway mode active Messages from GEOCARE® are
simultaneously sent to another
phone number.
Hereby, you have more service
options. However, depending on
the type of your contract, it could
cause additional costs.

GEOCARE® 25 GEOCARE®
24
INSTALLATION
Notes on „general settings“
SMS map style
Defines how the position of the emergency caller is displayed in
the SMS to the emergency alarm receiver
Text Plain text message with details of
coordinates.
All telephones
(manual map selection)
Working map link for all internet-
able phones. In an intermediate
step, the appropriate map must be
selected manually on the smart-
phone.
KML
(Google Maps für Nokia s60,
Windows Mobile)
Map link is already optimised for
Google Maps on Nokia phones
(Symbian 60) as well as on
phones with Windows Mobile.
LMX
(Nokia Navigator)
Map link is already optimised for
Nokia Navigator.
Blackberry
(Blackberry Maps)
Map link is already optimised for
Blackberry Maps.
Google Maps
(Android, Blackberry,
iPhone, Windows Phone 7)
Map link is optimised for display in
Google Maps.
This is a standard setting and true
in most application scenarios.
Deviation from UTC standard
Sets the current time zone
UTC
is the coordinated uni-
versal time at the prime
meridian in Greenwich. By
entering the relevant devi-
ation, GEOCARE® is set to
the correct local time.
+1 = Central European Time
+2 = Central European Summer Time
Important: It is essential to change the
settings when changing from winter to summer
time and vice versa to ensure that an incoming
emergency call is marked with the correct time
Disable on/off key Check the box if you wish to pre-
vent the user of the GEOCARE® de-
vice from switching off the device.

GEOCARE® 27 GEOCARE®
26
INSTALLATION
Usage Profile
Highest accuracy (40) GEOCARE® stores location data every
40 seconds. This storage interval
provides the highest accuracy and
lowest battery lifetime.
Precise (90) Location data are stored every 90
seconds.
This is the recommended setting.
Standard (120) Location data are stored every 120
seconds. This storage interval provi-
des an optimised setting in terms of
accuracy and battery lifetime.
Extended standard (180) Location data are stored every 180
seconds.
Long runtime (600) Location data are stored every 600
seconds.
Long runtime (1200)
Attention! with „Long runtime“ profile
enabled, the departure of the wearer
from a specific zone remains unde-
tected for a longer period of time.
Location data are stored every 1200
seconds.
Status message interval A status message is sent to the
emergency alarm receiver within a
defined interval of minutes. A such
interval is at least 240 minutes long.
Ring tone
Sound 1 to 3 There are three different ring tones
to choose from.
Handset volume Volume of the GEOCARE®
Charging cradle volume Volume setting for the external
charging cradle.

GEOCARE® 29 GEOCARE®
28
INSTALLATION
Alarm settings
Maximum emergency call
ringing duration
How long should the emergency
call ring at the emergency alarm
receiver’s end?
Maximum wait time for
emergency call confirma-
tion with key „5“
(Tone dialling)
Within the defined time, the emer-
gency call receiver must press key
„5“ on his/her telephone. If this is not
done within the set time, the connec-
tion is terminated and a new call is
made to the emergency call receiver.
Do not select a too long time interval. If an emergency call from GEOCARE® is answered by voicemail, GEO-
CARE® is blocked by voicemail for the complete duration of the selected time interval before it can continue
to work through its emergency call priorities
Call acceptance for non-
emergency calls activated
The GEOCARE® user can be called
from the telephone numbers config-
ured as emergency alarm receivers
without having triggered an SOS
alarm.
SOS alarm transmission
delay in seconds
Duration of SOS alarm‘s delay in
seconds. Enables cancellation of
false alarms before notification of
contact.
Wait time in seconds before
redial
( This value must be set for
each priority level
)
Duration for GEOCARE® to wait for a
return call before redialling . This has
to be done after GEOCARE® has estab-
lished and ended a connection to the
emergency alarm receiver without
speaking to him/her . The wait time is
given in seconds.
Number of emergency call
recurrences
How often should the emergency call
to an emergency alarm receiver be
repeated before the next recipient is
called?

GEOCARE® 31 GEOCARE®
30
INSTALLATION
Zone Configuration
Zones, home zones or hazard zones (NoGo-Zone) can be set by a
free selectable circular radius around a free selectable position.
When the fence is activated („fence active“), all authorised emer-
gency alarm receivers receive an SMS as soon as the wearer
leaves or enters the zone.
We recommend that you basically do not select a too small ra-
dius, because if you do, even small fluctuations in GPS signal
quality can trigger SMS notifications.
In these fields, you can define zones and reference points for GEOCARE® to use in its position reports.
Using the cursor, select the location you want to edit from the loca-
tions list (left).
Enter a concise description in the field „Name“. If you are setting
a „zone“, you can now also adjust the radius as well as enable or
disable the fence.
Enter the address information and click on the button „Determine
coordinates from address“. A green pin is placed on the adjacent
map (requires an Internet connection).
For checking purposes and if necessary fine corrections, you can
zoom in to this map. If the green pin is not exactly in the required
position, move the cursor to the required position and double click
— the green pin then jumps to this position.

GEOCARE® 33 GEOCARE®
32
INSTALLATION
SIM card settings: PIN, APN and AGPS
SIM card
Internet access set-
tings are automati-
cally adopted based
on the SIM card that is inserted. If necessary, you can change them
manually.
Make sure the APN Data are entered correctly. If these Data are
not correct, there is a possibility that the GEOCARE® restricted in
its functionality.
GPS
In order to accelerate the location detection, you can enable AGPS
(Assisted Global Positioning System). If GEOCARE® has not been in
use for a long period of time or has been in areas without any GPS
reception, the first location detection process usually takes a little
longer as some basic data must first be transmitted from the sat-
ellites. When using AGPS, these data are transmitted separately via
the mobile phone network. They then enable a quick position detec-
tion. This function imperatively requires the correct Internet set-
tings for the SIM card (see above).
GEOCARE® Hardware/status
In this tab, informations about the GEOCARE® are being displayed,
for example, the serial number, IMEI number and the telephone
number of the GEOCARE® device.
These details are automatically shown as soon as GEOCARE®
is connected to the PC.
If all details have been given in automatically, no more entries are
required from you. If this is not the case (if necessary e.g. phone
number), type in the missing informations and save them with the
button “Save” in the the top menu bar.

GEOCARE® 35 GEOCARE®
34
USAGE
Top menu bar
Save
Saves the configuration
settings simultaneously to
the GEOCARE® device and a
database that is managed
by the software. Prior to
clicking on the button „Save“
you must click once outside
the edited field.
Load from DB
Loads the last settings that
were saved to the database
into the PC software, even
if configuration settings on
the device have since been
changed via SMS commands.
Load from device
Loads the last settings that
were saved on the device
into the PC software.
Edit device
Opens the configuration
window.
Delete device
Removes the device from
the device overview.
Update firmware
Installs the most current
firmware version on the
device, when there is a new
version.
USAGE

GEOCARE® 37 GEOCARE®
36
USAGE
Wireless transmitter
You do not have to renounce
to safety while the GEOCARE®
device is being charged in the
charging cradle. The comfort-
able and stylish wireless trans-
mitter can be worn like a wrist-
watch on the wrist .
What looks like a watch dial
at first glance is actually the
easy-to-use SOS button. The emergency call is securely transmit-
ted via radio.
Special technology prevents call failures and accidental triggering
of an alarm. Of course the GEOCARE® wireless transmitter is wa-
terproof, and therefore ideal to wear when bathing or showering.
Details on the GEOCARE® wireless transmitter:
●Complies with the DIN standard for personal alarm systems / triggering devices
●Range: 250 metres outdoors, 30 metres indoors
●Simple to trigger alarm — directly from the wrist
●Radiobutton is the product name of GEOCARE®‘s wireless transmitter
First use of the wireless transmitter
Connect your GEOCARE® to your PC and start the GEOCARE® soft-
ware.
As soon as the GEOCARE® software has detected the GEOCARE®
(highlighted in yellow in the overview on the left of the display),
activate the GEOCARE® by double-clicking on the device in the dis-
play. Afterward, go to the main panel on the right, and move down
to the „ZigBee radio unit“ section.
It may take a few seconds until the device has been read out and
you can click the „ZigBee radio unit“ section.
Now click on the checkbox „Switch on“ in case it has not yet been
checked to activate the ZigBee module in the GEOCARE®. Next,
click on the „+“ icon.

GEOCARE® 39 GEOCARE®
38
USAGE
A dialogue box then opens (see above) and you have two possibili-
ties to connect the wireless transmitter to the GEOCARE®:
Connect by entering the IEEE address
Enter the IEEE number without hyphens in the previously opened
dialogue box and confirm with „OK“. The sixteen-digits IEEE num-
ber can be found on the packaging for the wireless transmitter
(e.g. 00-1B-C5-07-80-00-00-55).
Connect through automatic detection
Press the button on the wireless transmitter shortly until it shines
red. The wireless transmitter now tries to connect to the GEOCARE®.
This process can last up to 30 seconds. If during this time the wire-
less transmitter flashes a green light, then the connection was
completed successfully. If the the wireless transmitter flashes a
red light once again after 30 seconds, then the connection could
not be completed. In this case, please repeat the connecting pro-
cess once again until it shines green.
If you do not enter any IEEE address in the dialogue box, the GEO-
CARE® automatically connects to the wireless transmitter whose
signal is the strongest.
Caution: After the connection, it is imperative to run a test to en-
sure that the GEOCARE® is connected to the appropriate wirel-
ess transmitter. When the the wireless transmitter is success-
fully connected , it is indicated by an entry in the GEOCARE®
Enterprise Software.