Life Span SD9 User manual

Standing Desk
Owner’s Manual
SD9

TableofContents
2
Welcome
Getting Started 3
Welcome
Warranty
Power
SD9 Desk Assembly 6
Assembly Instructions
SD9 Desk Operations 17
Specifications
Console Buttons

Welcome
3
Congratulations onchoosing theLifeSpanWorkplace™ line of products.These
products give you the opportunity to remain productive while taking care of
yourselfasyouintegratemovementwithnormallysedentarytasks.
The average American now spends eleven hours, five days a week, sitting, and
burns one-hundred fewer calories each day than they did a few decades ago.
Sitting for long periods slows your metabolism, reduces calories burned, and
increases your risk for heart disease and diabetes.
Whether you plan on placing this product in a TV room, replace your desk at
home or are adding another workspace in the office, LifeSpan Workplace™
products are a great way to add movement to an otherwise sedentary activity.
Before you assemble or operate your product, please read this manual
thoroughly. Important information, including safety precautions, ongoing
product maintenance, assembly instructions, and information on proper
operation are included.
Neither LifeSpan Fitness nor its representatives canaccept responsibility for anydamagesor
injury incurred as a result of information presented in this manual except under the terms
of the product warranty.

4
Warranty
Your LifeSpan standing desk comes with the following limited warranty valid
in North America and the United Kingdom. If you are outside of these areas
contact your local distributor for warranty information or visit
www.LifeSpanFitness.com.
Warranty SD9
LifeSpan warrants the equipment it manufactures is free from defects in
materials and workmanship under normal use and services. The periods
above are based on the date of purchase. During these periods, LifeSpan will
replace defective parts. Free labor is included on all parts that are not normally
assembled or replaced by the customer within the labor period.
LifeSpan reserves the right to make changes and improvements to our products
withoutincurring any obligations tosimilarly alter any product purchased.
In order to insure our product warranty and to ensure the safe and efficient
operation of your LifeSpan product, only authorized parts can be used. The
warranty is void if any parts other than those provided by LifeSpan are used.
Exclusions and Limitations:
• This warranty does not apply to any defects caused by negligence, misuse,
improper assembly, or maintenance, accident, or “act of God.”
• This warranty does not apply to discoloration of paints or plastics.
• LifeSpan shall not be responsible for incidental or consequential damages.
• This warranty is non-transferable form the original owner.
Frame & Parts 2 Years

5
About Your StandingDesk
Proper Grounding
LifeSpan equipment must be grounded. Improper connection of the
equipment’s grounding conductor can result in the risk of electric shock.
Check with a qualified electrician or service person if you are in doubt as to
whether the outlet is properly grounded. Do not modify the plug provided
with the product or use a ground plug adapter to adapt to a non-grounded
outlet. If the plug will not fit in the outlet, have the proper outlet installed by a
qualified electrician.
Power Cord Options
This standing desk should only be used with the proper power cord and
power outlet. Several power cord options (shown below) are available from
LifeSpan. We do our best do include the correct power cord with the standing
desk for your area. In the event that the correct power cord is not included in
the packaging please contact your local distributor.
Do not use extension cords between the standing desk and power
outlet.
!

6
SD9 Standing Desk: Assembly Instructions
At LifeSpan we strive to make our equipment easy to assemble and start
using. Parts that can be pre-assembled are always assembled and tested on
the product line.
Prior to starting the assembly process, take all the parts out of the box,
remove plastic bags and lay everything out on the floor to become familiar
with the components.
Since your desk is a heavy piece of equipment, itis recommended that you
use two people during assembly and follow these assembly instructions to
reduce any problems that may occur.
Desktop ShipsSeparately
3
9
2
1
11
4
10
8
5
7
12
Tool Bag - Contents
5mm Allen 4mm Allen 2.5mmAllen
Wrench Wrench Wrench
6
w/Phillips w/Phillips w/Phillips

7
SD9 Standing Desk: Assembly Instructions
Hardware Included
Bag #
Item #
Qty.
Part Description
1
13
6
M8x12L Screws/Washers
2
14
8
M8x55L Bolts/Washers
3
15
6
M6x15L Screws/Washers
4
16
8
M8x35L Screws/Washers
4
17
6
M6x15L Screws/Washers
5
18
3
M4 x10L Screws/Washers
6
19
2
Phillips Screws
7
20
4
Cable Ties
Item#
Part Description
1
Front Reinforcement Frame
2
Back Reinforcement Frame
3
Desktop
4
Right Motorized Leg
5
Left Motorized Leg
6
Left Base Foot
7
Right Base Foot
Item#
Part Description
8
Left Desk Support Bracket
9
Right Desk Support Bracket
10
Electronics Control Box
11
Height Controller
12
Power Cord
M8x12L (x6)
STEP 1BAG
M8x55L (x8)
STEP 2BAG
M6x15L Screw
(x6)
STEP 3BAG
M8x35L Screw M6x15L Screw
(x8) (x6)
STEP 4BAG
M4x10L Screw
(x3)
STEP 5BAG
PhillipsScrew
(x2)
STEP 6BAG
CableTies
STEP 7BAG

8
SD9 Standing Desk: Assembly Instructions
Step 1: Attach Right and Left Side Bracket
A. Add the Left Desk Support Bracket(8) to the Left Motorized Leg(5). Each will
have an “LLL” sticker attached for easy identification.
B. Stand the leg on the motor side as shown in the illustration and align the
bracket.
C. Locate the screws for Step 1 and hand tighten the bracket to the leg.
Then securely tighten with the included tool.
D. Repeat for the Right Desk Support Bracket(9) and Right Motorized Leg(4).
Set Screws
5
5mm Allen
Wrench w/
Phillips
8
M8x12L (x6)
LOCATE BAG LABELED STEP 1
Contents: 6 each M8x12L screws with washers
NOTE: Make sure that the
power cable isn’t set hard
on the ground which
could damage the wire.
NOTE: Do not tighten or
loosen set screws. They
have been pre-adjusted
prior to shipping.

9
SD9 Standing Desk: Assembly Instructions
Step 2: Attach Base
A. Align Left Base Foot(6)
labelled 'LLL" with the
Left Motorized Leg (5) and
connect the wires.
B. Push ALL extra wiring into
theLeftBaseFoot(6).
LOCATE BAG
LABELED STEP 2
Contents: 8 each M8x55L
bolts with washers
6
6

SD9 Standing Desk: Assembly Instructions
10
C. Connect the Left Base
Foot(6) to the LeftMotorized
Leg(5) with the fourM8x55L
Bolts with Washers(14).
D. Insert fourM8x55LBolts(14)
being careful not to
damage wires inside the
Left Base Foot(6).
E. Hand tighten each of the
fourbolts.
F. Tip the left post on its side.
G. Repeat the same procedure
on the right side.
6
5mm Allen
Wrench w/
Phillips
M8x55L (x8)
Step 3: Attach Desktop to Posts
3
LLL
RRR
RRR
A. Place the left post on
top of the Desktop(3) as
shown in the illustration.
Tighten each of the three
M6 Phillips Screws and
Washers(15) as shown.
B. Repeat on the right side.
M6x15L Screw
(x6)
4mm
LOCATE BAG LABELED STEP 3
Contents: 6 M6x15L Screws and Washers
NOTE:
Be careful not to let
the post tip.

SD9 Standing Desk: Assembly Instructions
11
Step 4: Attach Reinforcement Frame
A. Locate the Front Reinforcement Frame labelled (1) and the Back
Reinforcement Frame labeled (2). Place these frames on desktop with
screw tabs down and facing each other as shown in figure below.
B. Extend Front and Back Reinforcement Frames(1, 2) to align all mounting
holes with Desktop(3) and Motorized Legs(4, 5).
C. Loosely install the eight M8x35L(16) bolts through the Reinforcement
Frames(1,2) and into the Motorized Legs (4,5).
D. Tighten all eight M8x35L(16) bolts.
E. Using the six M6x15L Screws(17) attach both reinforcement frames to the
desktop as shown in the illustration.
F. Tighten the pre-installed Set Screws(A) . Be careful not to overtighten as
the tube will bend.
NOTE:
72" desktop shown for clarity of frame
components. When mounting the frame
16
to smaller desktop sizes, the front and 5
back reinforcement frame pieces slide and
17
compress into shorter lengths.
17
Center Positions
16
17 2
A
16
1
4 A
3
16
5mm Allen
Wrench w/
Phillips
Front
M8x35L Screw
(x8)
M6x15L Screw
(x6)
4mm
LOCATE BAG LABELED STEP 4
Contents: 8 each M8x35L Bolts with Washers, 6 each M6x15L Screws.

SD9 Standing Desk: Assembly Instructions
12
Step 5: Attach Electronics Controller Box
A. Guide the cable with the square connector(B) to the middle of the desk as
shown.
B. Connect the 2 pin power cable(C) to the Electronics Controller Box(10).
C. Secure the Electronics Controller Box(10) in place with three M4 screws(18).
D. Attach square connector cables (B, D) to the left side of the Electronics
Controller Box(10).
18
C
Right Side 10
B
Square
Connector
Cable
Left Side
B
M4x10L Screw
(x3)
D
2.5mm
LOCATE BAG LABELED STEP 5
Contents: 3 each M4x10L Screws/Washers

SD9 Standing Desk: Assembly Instructions
13
Step 6: Attach Height
Controller
A
Height
Controller
Mounting Clip
B
C
A. LocateMountingClipand
Height Controller(11).
B. Connect Mounting Clip to
Height Controller by lining
up the locking tabs.
C. Slide Mounting clip
backward to locking
position.
D. Attach to right side of
desktop with 2 Phillip
screws(19) into pre-drilled
holes.
D
19 19
Viewfrombeneath
Desk & Height
Controller
Phillips Screw
(x2)
LOCATE BAG STEP 6
Contents: Height
Controller, Mounting Clip,
2 Phillips Screws

SD9 Standing Desk: Assembly Instructions
14
Step 7: Attach Height Controller Cable
A. Locate end of Height Controller Cable (E), guide through hole in Front
Reinforcement Frame (1) and connect to the Electronics Control Box(10).
B. Attach Cable Ties(20) to underside of desk in areas to best secure the
Height Controller Cable.
10
Left Side
E
20
Cable Ties
LOCATE BAG LABELED STEP 7
Contents: 4 Cable Ties

SD9 Standing Desk: Assembly Instructions
15
Step 8: Turn Upright and Attach Power
A. Use 2 people to lift and turn upright; and position on floor where
desired.
B. Connect the Power Cord (12) from rear Left Desk Foot to an outlet.
12
12
Close-up

16
Standing Desk
Operations

17
SD9 Standing Desk: Console Overview &Specifications
CONSOLE
SD9
Readouts
Display
Height Adjustment Levels
White LED
Buttons
Height Adjustments,
Memory Pre-sets
Console Buttons
1. S: Sets desk to desired height. Adjust desk height. Hold 'S' button down
until display flashes. Push and hold 1,2,3 or 4 until number shows in
display. This sets your desired height to that button.
2. 1-2-3-4: Pre-set buttons remember 4 different heights.
3. Display : Shows height number setting from range of 079-099.
4. : Increases or decreases desk height.
1
2
3
4

18
SD9 Standing Desk: Console Overview & Specifications
Error Codes
Error Code Description Handling Steps
HOT
Overheat- System detects
the action by not following
the rated duty cycle and pre-
vents it fromoverheating.
Stop operating
until cool off.
E01
Overload- System detects
excessive weight*
arrangement by not
following the rated capacity
Please remove some
weight.Releasebuttonthen
press again can continue
operationandshowcurrent
height.
E16
Block- System detects a
sudden resistanceor pinch
during moving.
Release button. Remove
the block source then press
button again can continue
operation.
* Rated weight capacity is 220 lbs (100kg)
Calibration
1. Press and hold S and UP buttons. The S button needs to be pressed and
held first then the UP button so both are being held at the same time.
After a second or two the display will start flashing“Set”. The buttons can
be released. The desktop will go to the lowest position and then to the
highest position and then back to the lowest. The console will then show
the normal reading of the desktop.

SD9
Standing Desk
Version 1.4