Lifepro SIRS-01 User manual

Questions, problems, missing parts? Contact technical support department at
1-866-484-2066, 8:00 a.m. - 5 p.m., CST, Monday - Friday or www[email protected]
Please have your model and serial number ready.
1
REV2-071514
ATTACH YOUR RECEIPT HERE
Purchase Date ____________Serial Number (located on back of unit) __________________
lifepro®is a registered trademark
of Source Network Sales & Marketing Inc., All Rights Reserved.
INFRARED STOVE HEATER
MODEL #: SIRS-01

2
TABLE OF CONTENTS
Package Contents ..............................................................3
Safety Information ..............................................................4
Frequently Asked Questions ......................................................6
Preperation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Troubleshooting ................................................................8
Control Panel ..................................................................9
Operating Instructions ..........................................................10
Care and Maintenance..........................................................11
One-Year Limited Warranty ......................................................12
Replacement Parts List .........................................................13

3
PACKAGE CONTENTS
A
C
Rear View
Front View
D
E
F
B
PART DESCRIPTION QUANTITY
A Infrared Heater 1
B Control Panel (preassembled to Infrared Heater (A)) 1
C Heat Output Vent (preassembled to Infrared Heater (A)) 1
D Master Power Switch (preassembled to Infrared Heater (A)) 1
E Heat Shield (preassembled to Infrared Heater (A)) 1
F Heater Leg (preassembled to Infrared Heater (A)) 4

4
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate, or install the
product.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: POTENTIAL ELECTRICAL HAZARD IF NOT ADHERED TO. When using electrical
appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and
injury to persons, including the following:
• This heater must be plugged into a 220 V, 7.5 amp (or more) circuit of its own. Do not plug anything
else into the same circuit. If unsure if your home meets this specification, consult a certified
electrician prior to use. Risk of fire, overheating, malfunction, property damage, injury, or
even death may result if not adhered to!
• Connect to a properly grounded, 3-prong outlet only. Do not connect the heater to extension cords,
surge protectors, timers, direct breakers, or an outlet with other appliances connected to the same
outlet. Risk of fire, overheating, malfunction, property damage, injury, or even death may
result if not adhered to!
• This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Use handles
(certain models) or wheels to move this heater.
• Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at
least 3 ft. (0.9 m) from the front of the heater and keep them away from the sides and rear of the
heater.
• Extreme caution is necessary when any heater is used by or near children, invalids, pets, or when
the heater is left operating unattended.
• Always unplug the heater when not in use.
• Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been
dropped, or damaged in any manner. Contact the manufacturer for resolution options.
• Do not use outdoors. Exposure to outdoor elements such as rain, snow, sun, wind, or extreme
temperatures may cause the heater to become a safety hazard.
• This heater is not intended for use in bathrooms, laundry areas, and similar indoor locations, nor
any locations that use GFCI outlets.
• Never place the heater where it may fall into a bathtub or other water receptacles.
• Do not run the cord under carpet. Do not cover the cord with throw rugs, runners, or similar
coverings. Arrange the cord away from traffic areas and where it will not be tripped over.
• The heater must be plugged into a wall outlet that is a dedicated circuit with a minimum 15 amp
rating on that individual circuit.
• To disconnect the heater, first turn the power button to the OFF position and then remove the plug
from the wall outlet.
• Do not allow foreign objects to enter or block any ventilation or exhaust opening as this may cause
electric shock, fire, or damage the heater.
• Allow at least 3 ft. of unobstructed space to the front and rear of the heater to allow for maximum
heat, air, and ventilation flow.
• A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint,
or flammable liquids are used or stored, nor use flammable solvents to clean the heater. Keep the
heater dry at all times.
• Use this heater only as described in this manual. Any other use not recommended by the
manufacturer may cause fire, electric shock, or injury to persons.
• Do not use abrasive solvents to clean the heater as it may cause
damage to the finish or casing.

5
SAFETY INFORMATION
Overheat Safety Feature
This heater is equipped with an overheat safety feature. When the internal components of the
heater reach a certain temperature that could cause overheating or possible fire, the heater will
automatically shut off.
WARNING: This heater has a voltage
rating of 220 volts. The cord has a three-
blade, grounding-type plug. An adapter
is available for connecting three-blade
grounding-type plugs to two-slot receptacles.
The grounding plug extending from the
adapter must be connected to a permanent
ground such as a properly grounded outlet
box. The adapter should not be used if a
three-slot grounded receptacle is available.
DO NOT DEFEAT THE SAFETY PURPOSE
OF THE GROUNDED PLUG.
Grounding Pin
Grounding Means Grounding Pin
Metal Screw
Cover of Grounded
Outlet Box
WARNING: It is normal for the power cord to feel warm to the touch. However, a loose fit between
the outlet and the plug may cause overheating of the plug. If this occurs, try inserting the plug into a
different outlet. Contact a qualified electrician to inspect the original outlet for damage.
Specifications
Voltage Rating 120 V (60 Hz)
Power Consumption 500 W/1,000 W
Unit Size 16.4 in. (W) x 10.9 in. (D) x 21.5 in. (H)
Unit Weight 16.9 lbs.

6
FREQUENTLY ASKED QUESTIONS
Please review these frequently asked questions on the next few pages prior to using your heater.
Q. My heater emits a strange odor when I first open the box and when I turn the heater on for
the first time. Why is this happening?
A. This is normal. This heater is treated with a special heat safe/resistant coating. This odor will
sometimes be present when the box is opened. When the coating is exposed to heat, it produces this
particular odor during the first few hours of operation. This will dissipate after the break-in period. If
you are sensitive to odors, you may want to pre-burn the unit in a garage with the door open until the
initial odor dissipates.
Q. If my heater runs on approximately 1,000 watts, how many BTUs is that? Is that a lot of
heat?
A. At 1,000 watts, your heater will produce approximately 3,400 BTUs. This heater is intended to be
used as supplemental heat in areas most needed. It may take several minutes to several hours to
heat your area, depending on various factors.
Q. Can the heating elements be replaced?
A. Replacement heating elements can be obtained from the manufacturer. All parts may be
purchased through the manufacturer if your product is out of warranty. If you feel that the elements
are definitely faulty right out of the box, contact technical support. A representative can then direct you
to the next step.
Q. Once I plug the unit in and turn it on, how long will it take to heat my room?
A. The heating process in the heater begins immediately upon powering on and setting the desired
temperature above the ambient temperature. A noticeable change in the ambient temperature of the
room will vary due to variables such as the location of the heater (in the home), floor plan and size of
the room, how well the room is insulated, how many doors/windows, how much bare concrete (acts
as a heat sink with any type of heating), the opening and closing of an exterior door, long hallways,
high ceilings, etc. Customers with smaller rooms experience quick heat changes. Rooms with larger
and open floor plans can expect up to 24 hours to completely heat up.
Q. I do not have a grounded outlet. Can I use a 2-prong power strip, or remove the ground
prong from the cord?
A. NO! If you do not have a grounded outlet, contact a certified electrician for advice. Removing
or altering any part of the heater’s original design or intent (including the power cord) will void the
warranty and make you liable for any unexpected or hazardous results.
Q. What light bulb can I use for the flame effect?
A. The heater uses two T4 shaped / G9 base 25 watt bulbs.

7
FREQUENTLY ASKED QUESTIONS
Q. Can I use more than one heater at a time? Can I use the heater and another appliance at the
same time?
A. Yes, but make sure they are not plugged into the same circuit. Each heater requires its own
minimum 15-amp circuit with no other items plugged into that circuit or outlet. This is because heaters
are considered appliances and draw out high amperage. If you are unsure whether your circuit meets
these requirements, verify with a certified electrician.
WARNING: Risk of fire, damage to property, or injury may result if requirements are not met.
Q. Why does my heater’s fan continue to run after the set temperature is reached or the power
is turned off?
A. This is normal. The heater’s fan will continue to run even after the heater automatically cycles
down. The fan continues to run so that every last bit of heat is blown out of the heat chamber while
allowing the unit to continue filtering your air. Once the internal box/components cool completely, the
fan should then shut off on its own. In this case, allow a few minutes after the heat cycles off (with
power on). The fan will shut off faster when the power is turned off.
Q. My heater’s power cord gets warm. My cord is showing signs of heat or melting at the
outlet. Is this normal?
A. A warm power cord is normal. These power cords are rated safe for up to 105°C/ 221°F by the UL,
CSA, or ETL. The exception is, if you detect heat, smoke, or signs of melting at the contact point of
the wall outlet, it may be due to loose or worn wall contacts (or arcing). Please stop using the heater
immediately, contact warranty support for a replacement power cord, and have a certified electrician
replace the wall outlet as soon as possible.

8
PREPARATION
Place the heater on a firm, level surface and plug into a grounded 120 V, 60 Hz power outlet and turn
on the power switch on the bottom front of the unit. Only operate heater in upright position.
Please note that infrared heaters do not heat like a traditional space heater. You should not expect
infrared heaters to blow hot air like a traditional space heater. Infrared heaters heat objects not air.
Infrared heaters are intended to supplement an already heated, insulated room. Square footage
specifications assume a single enclosed room not an entire home. Infrared heaters do not heat
through walls, floors, and are not intended to replace a main heat source. Infrared heat can take at
least 24 hours to warm a room but operate much more efficiently to maintain the desired temperature.
Infrared heaters will not work well in uninsulated unheated spaces like screened in porches, RV’s,
garages, unheated basements, etc.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
The heater does not
power on.
1. The power cord is not plugged in.
2. The electricity at the main fuse box is
not working.
3. The power switch in the front is not on.
1. Plug the power cord into an electrical outlet.
2. Check the electricity at the main fuse box.
3. Flip the power switch to the on position
The flame effect does
not turn on
1. The flame intensity is low.
2. There is no light for the flame
1. Increase the flame intensity with the knob.
2. Change the light bulb.
There is no heat from
the unit
1. The thermostat on the heater is set
lower than the room temperature.
2. The switch for heat is not on.
1. Increase the thermostat temperature on the
heater to a higher heat setting.
2. Flip the low and/or high heat switch to the on
position.

9
CONTROL PANEL
2 3 4 5 6
500W 500W Flame
Effect
1
Fan
Switch
PART NAME DESCRIPTION
1 Thermostat Knob Increases or decreases desired temperature
2 Fan Switch Engages fan for heat mode
3 Heat Switch One Engages power to 500 watt mode
4Heat Switch Two Engages power to 500 watt mode
5 Flame Effect Switch Powers the flame effect ON or OFF
6 Flame Brightness Knob Increases or decreases desired flame effect brightness level

10
OPERATING INSTRUCTIONS
1. Turn the heater on or off by pressing the Power
switch on the heat output vent assembly (C) to the I
position.
1
B
Master
Power Switch
2. Turn the fan switch to the on position. Then select a
heat setting by pressing the 500 W heat buttons on
the control panel (C).
Power one heat mode for 500 W; power both heat
modes for 1,000 W.
2
B
Fan
Switch
500 W500 W
3. Set the thermostat by turning the thermostat knob on
the control panel (C)
To increase the desired temperature, turn the
thermostat dial to the right (clockwise) to increase, or
left to decrease temperature. The thermostat control
knob can only be used while the Power and Heat
switch/switches are in the on position.
Once you have chosen the desired temperature,
the heater will remain on until the room temperature
increases to that level. Then, the heater will cycle on
and off to maintain the desired room temperature.
3
B
Clockwise
4. To adjust the flame effect brightness, turn the dimmer
dial clockwise or counter clockwise. The dimmer
switch can only be used when the power switch is in
the ON position.
4
B
Clockwise

11
CARE AND MAINTENANCE
WARNING: Before performing any maintenance task, turn off the power switch in the front of the
unit, unplug the unit, and allow it to cool completely.
1. To keep the heater clean, clean the outer shell with a soft, damp cloth. Use a mild detergent if
necessary. After cleaning, dry the unit with a soft cloth.
CAUTION: DO NOT let liquid enter the heater.
2. DO NOT use alcohol, gasoline, abrasive powders, furniture polish, or rough brushes to clean the
heater. This may cause damage or deterioration to the surface of the heater.
3. DO NOT immerse the heater in water.
4. Wait until the unit is completely dry before use.
5. If you will not be using the heater for a while, take the batteries out of the remote control and
store for future use.
6. Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-up, use
the original packaging to repack the unit.
CHANGING THE LIGHT BULB
1. Unscrew the back cover of the heater.
2. Replace necessary light bulbs with T4 shape / G9 base 25 watt light bulbs.
3. Re-install back cover in place.
WARNING: Do not use the heater without all assembly in place.
Screws
Screws
Screws

12
ONE-YEAR LIMITED WARRANTY
The manufacturer warrants this heater against defects in materials and workmanship on functional
parts, for a period of 1 year from the original date of purchase. Your sales receipt showing the date of
purchase of the product is your proof of purchase. Keep it in a safe place for future reference.
This product is made with the highest quality materials and is warranted to be free from defects
in materials and workmanship at the time of purchase. This limited warranty applies to products
manufactured or distributed by the manufacturer, are delivered in the continental United States,
and extends to the original purchaser, or gift recipient. This warranty becomes valid at the time of
purchase and terminates either by the specified time frame listed above and/or owner transfer. Any
refunds or monetary compensations must be claimed through the place of purchase (retailer), and
not through the manufacturer. Any extended warranties (warranties that cover above and beyond this
manufacturer warranty) that are sold through a retailer or third party, are not directly correlated with
this products’ limited warranty, and may be redirected to said retailer or third party for coverage.
This warranty extends through the manufacturer of the product, and covers functional parts only.
Cosmetics are not covered, unless unequivocally determined it is a workmanship defect. Shipping
damage should be addressed with the shipping company, retailer, or place of purchase, not the
manufacturer unless the manufacturer was the direct shipper.
The manufacturer’s sole obligation under this warranty shall be limited to furnishing the original
purchaser replacement parts for units deemed repairable by the supplier’s warranty department.
The purchaser is responsible for insuring any parts shipped or returned, if desired. The purchaser
is responsible to prepay any shipping charges (both ways) including, but not limited to taxes and
duties. All exchanged parts and products replaced under this warranty will become the property of
manufacturer. The manufacturer reserves the right to change manufacturers of replacement parts or
products for use, in order to cover any existing warranty.
The purchaser may be asked to provide the supplier with proof of purchase documents (including the
date of purchase) if requested. Any evidence of alteration, erasing, or forgery of proof of purchase
documents will be just cause to VOID this limited warranty. Products, in which the serial number has
been defaced or removed are not eligible for warranty coverage.
This warranty does not apply if the unit has been subject to negligence, fabrication, misuse, abuse, or
repairs, alteration by non-manufacturer authorized personnel, inappropriate installations, or any case
beyond the control of the manufacturer. Examples of warranty invalidation may also include, but are
not limited to:
• Use of lacquer or paints in (and around) the heaters
• Heater placed on non-approved surfaces
• Electrical requirement deficiencies (15-20 amp dedicated outlet)
• Use on extension cords/timers/surge protectors/GFCI
• Outdoor applications
• Normal wear/tear/weathering
• Pet/consumer accidents
The manufacturer shall not be liable for any loss due to use (or misuse) of the heater or other
incidental or consequential costs, expense or damages without irrefutable foundations. Under no
circumstances shall the manufacturer or any of its representatives be held liable for injury to any
person or damage to any property, however arising. Any implied warranty shall have duration equal
of the applicable warranty stated above. Specifications are subject to change without notice or
obligation.
This limited warranty gives the original purchaser specific legal rights. Other rights may vary from
state to state

13
Printed in China
lifepro®is a registered trademark
of Source Network Sales & Marketing Inc., All Rights Reserved.
PLEASE REMEMBER TO REGISTER YOUR WARRANTY:
[email protected]
REPLACEMENT PARTS LIST
For replacement parts, call our technical support department at 1-866-484-2066, 8 a.m. - 5 p.m.,
CST, Monday - Friday
PART DESCRIPTION PART #
A Control Panel RH121348
B Fan RH124063
C Motor RH124060
DLimit Thermostat RH124065
EInfrared Tube RH124061
F Light Bulb RH121337
A
B C
E
D
F