Light Projects Evica EP20CC User manual

Evica EP20CC LED Gobo Effects Projector
Issue: 28/07/2017
Copyright ©2017. Light Projects Group Ltd.
All Rights Reserved.
Model number: 5372**-***-**-**

Notice
The information contained within this document is subject to change without notice.
Evica Ltd makes no warranty of any kind with regard to this material, including, but not limited to, the implied
warranties of merchantability and tness for a particular purpose.
Evica Ltd shall not be liable for errors contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this material.
No part of the document may be photocopied, reproduced, or translated to another language without prior
written consent of Evica Ltd.
Safety instructions and precautions
• Never look directly into the beam or shine in anyone’s eyes.
• Do not block the cooling fins..
• Ensure that there is sufficient ventilation around the unit, recommended minimum 1m².
• The IP40 version of the product is designed for indoor use only and should not come into contact with
water or excessive dust.
• The IP65 version is suitable for exterior use limited to water spray from all directions. DO NOT allow
contact with strong water jets or to be submerged in water.
• Apart from Gobo holder and lens assembly there are no user serviceable parts inside.
• Use only approved accessories.
• Do not use this device in the presence of flammable or oxygen rich atmospheres.
• To prevent injury, this apparatus must be securely attached to the ceiling/wall.
• Use only with remote Constant Current LED drivers. 700mA Maximum. 29 - 33.8Vdc
•Connect: Red Core to +ve Black Core to -ve
Maximum working ambient temperature: 35°C
In hotter environments installer to install time switch or similar to ensure projector is not switched on in
full daylight or excessive temperatures.
In enviroments hotter than 35°C, limit drive current to 500mA
Light Projects 23 Jacob St London SE1 2BG Tel [phone]
Website www.lightprojects.co.uk Email [email protected]
Contents
Safety instructions and precautions
Installation
Operation
Cleaning and maintenance
Service
Guarantee

Light Projects 23 Jacob St London SE1 2BG Tel [phone]
Website www.lightprojects.co.uk Email [email protected]
Installation
Prior to mounting the unit please refer to the distance/spot size charts below to achieve the required image
size.
Fix the projector to selected mounting bracket by passing M10 stud or bolt through hole in stirrup and
securing with nuts and washers supplied.
Operation
1. Loosen screws in side of stirrup with Torx Head Key to
adjust tilt. Aim projector in desired direction and tighten stirrup
screws and M10 xing nuts to lock into position.
Connect projector cable to remote LED constant Current
Driver. Ensure Driver is switched off before connecting. Switch
on power to Driver and check LED illumination.
2/3. To remove Gobo Cassette, rst unscrew the screws
located on the underside of the projector with the Torx Head
Key provided. Slide out the Gobo Cassette.
4. Remove retaining ring from the cassette, place the gobo
slide into the recessed pocket in the cassette and re-insert the
ring to hold the gobo in place. Orientate Gobo in approprate
position bearing in mind image will be projected inverted
and reected side to side. Then insert the cassette back into
the projector making sure the rubber seal is still inplace and
the shiny side of the gobo slide faces the light source, check
image is orientated as desired. If neccessary slide holder out
and rotate gobo to correct alignment. When image is projected
correctly, retighten xing screws.
5/6. To focus the projector, rst remove the front plate by
unscrewing the 2 screws with the provided Allen Key.
7. Insert the focusing tool provided, locating pins in tool with
grooves in the lens. Then rotate the lens until image is in
focus. Remove the tool. Make sure the glass in the front plate
is clean with soft dry cloth and gasket is still in place (only on
IP65 version). Finally replace front plate and thighten screws.
Distance
1m
Medium
Angle 16.5°
0.29m
Narrow
Angle 11.5°
0.2m
Wide Angle
19°
0.33m
2m 0.58m0.4m 0.66m
3m 0.87m0.6m 0.99m
1.
3.
4. 5.
6.
4m 1.16m0.8m 1.32m
Diameter of Beam
Gobo Projector
2.
7.

Light Projects 23 Jacob St London SE1 2BG Tel [phone]
Website www.lightprojects.co.uk Email [email protected]
Cleaning and Maintenance
Periodically clean the front glass with a lint free cloth and a small amount of glass cleaner if necessary.
Check that the exterior cooling ns are free from dust or blockages, clean with a vacuum cleaner nozzle if
necessary.
Service
In case of a fault please contact inf[email protected]
Guarantee
The Evica product range is provided with a 3 year guarantee against manufacturing and material defects when
installed according to the product specication and used under recommended working conditions. Full details
available on request.
LED Module: Limited Guarantee
In Ambient • 25°C Max Driver Curent: 700mA 3 year Guarantee
• 35°C Max Driver Curent: 500mA 3 year Guarantee
• 35°C Max Driver Curent: 700mA 1 year Guarantee
• Otherwise Chargeable replacement of LED module
Limits of the guarantee: At its sole discretion, Evica Ltd agrees to repair or replace products deemed by Evica
Ltd to be defective. Evica Ltd reserves the right to replace a product with a like replacement that fulls the
same purpose. This replacement product may have graphics or nishing different from the original.
It is the product users responsibility to examine the product on a regular basis to determine the need for
servicing and or a replacement.
Products that have been neglected, modied or poorly maintained are not covered under the guarantee.
Damage from causes other than defects in materials and workmanship (e.g. lack of experience, ability or
competence) are not covered under the guarantee.
The nish or aesthetics of Evica Ltd products are not covered under the guarantee.
Any labour or postage costs associated with the removal, replacement or reassembly of the product are not
covered under the guarantee.
Normal wear and tear and maintenance are not covered under the guarantee
Rev: 17.7