Line Magnetic LM-503PA User manual

OWNER’S MANUAL
LM-503PA

Table of contents
Table of contents 2
Package contents 3
Product features 3
Specifications 4
Safety instructions 4
Recommendations 5
Recycling product 5
Glossary 5
Location and precautions 6
Power sources 6
Warranty 6
Functions descriptions (front view) 7
Functions descriptions (rear view) 8
Bias adjustment (top view) 9
Speaker connection 10
Audio connection 11
Turning on 12
General observations 12
Tube replacement 13
Maintenance 13
Troubleshooting 14
Thank you for choosing a Line Magnetic product. Its implementation has been our know-how, both in terms of design to
the manufacturing. Electronic components and mechanical parts correspond to the selection criteria of very high quality.
Operation and finish of each product have been checked before delivery. To obtain best results, please read the advice
contained in this document.
Please read this manual carefully before installation and operation.
In order to prevent damage during transportation, the amplifier and its tubes are packed with protective foam, please
remove these foam pieces before operating your amplifier to avoid any risks!
2

1x LM-503PA
2x Fuses
1x Detachable power cord
1x This user manual
WARNING
Product features
Package content
Make sure that the device is not plugged into the mains before making any connections. It is also recommended to turn
off or disconnect all other devices associated while making connections to the product.
Keep all packing materials for future use and please fill in the warranty card for registration of warranty.
Please make sure that your local voltage is the same as indicated on the rearpanel. A too low or too high voltage can
cause serious damage to your amplifier. In case you find an improper voltage, please contact our company or your local
dealer.
-
-
-
-
-
-
-
-
-
-
Hand-made construction with the finest point-to-point wiring.
Specially designed toroid transformer for power supply.
In the pre-stage we are using 310A tube developed by our company and in the driver stage it is 300B tube we have
used.
845 tube has been used for Single ended Class A power amplification.
User bias control has been used for bias adjustment and meters are available for monitoring the value.
In the input stage it is selectable between Balance transformer input and RCA input.
LM-503PA uses specially designed high grade EI type of Class A output transformer with wide bandwidth.
Soft Start and time delay Circuit.
Big loop Negative Feedback and Small loop Negative Feedback are available in order to meet different listening
requirement.
Metal and removable tube guard cage, easily installed tube cover for better protection.
3

Safety instructions
We invite you to read the instructions on the proper use of your product carefully. They will ensure the proper functioning
of the latter and it safely.
.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Do not use this device in a wet area, near water, do not expose to rain or moisture.
Do not place any objects filled with liquids such as vases or some others on the top or around.
Do not move the product if it has just been used or if it is still hot.
Do not install near heat sources.To avoid being overheated please keep the unit’s ventilation open.
Never cover the ventilation of the unit.
Amplifier should install steadily and make sure all four feet are on the same level.
Keep the amplifier in 15 cm’s distance to the surrounding walls.
Temperature will become higher after working in long period of time and please keep the unit’s ventilation open and
install the amplifier at a well-ventilated place to avoid troubles and fire hazard.
Clean only with a dry cloth. As a precaution, it is best to unplug the unit before handling and ensure the heat generated
by the product has been properly dissipated.
Please move the amplifier carefully not to drop the unit or be subject to other strong shocks.
Unplug the power cord if you are not going to use the product for an extended period of time or during lightning storms.
Take great care of electrical connections (power cord and plugs). In particular, do not walk on, or press the power cord,
specifically at plugs, power plant and the output of the power supply.
Be sure to use an appropriate power supply to the power jack on the unit outlet. Especially if the device is equipped
with a ground plug, it is necessary to use it.
Forbidden to operate when the output is open or shorted.
Do not attempt to service this product yourself. Opening the cover may expose you to dangerous voltage or other
hazards.
Use only spare parts and accessories recommended by Line Magnetic.
We are not responsible for any problems caused by checking and opening without permission of our company. For
service, please contact a local dealer or qualified service technician.
Power output: 24W Working conditions:
Temperature: 0°C to 40°C
Moisture: 20% to 80%
Frequency response (±1,5dB): 15Hz-35KHz Storage conditions:
Temperature: -20°C to 70°C
Moisture: 20% to 90%
Input sensitivity: 1000mV THD: 1%
S/N ratio: 87dB
Dimensions (W x H x D): 287 x 279 x 574 mm Input impedance: 100kΩ
Output impedance: 4Ω, 8Ω, 16Ω
Tubes: 1x 310A, 1x 300B, 1x 845, 1x 5U3C Net weight: 32kg
Power requirements: 230V ±5% (50Hz) Power consumption: 290W
4

Glossary
This symbol alerts the user to the presence of unprotected dangerous voltages which may pose a risk of
electric shock to the user.
This symbol alerts the user that the documentation that comes with the device contains important instructions
for maintenance and proper use of the product.
The CE mark indicates that this product complies with European directives Low voltage (2006/95/EC),
Electromagnetic Compatibility (2004/108/EC) and apply eco-design requirements for energy products
(2009/125/EC) when the appliance is installed and used in accordance with the user manual.
For continued compliance only Line Magnetic accessories must be used with this product and servicing must
be performed by specialized and qualified staff.
The WEEE symbol is that of the European Union regarding the recycling of electrical and electronic
equipment. It indicates that this product contains electrical and electronic components that can be reused,
recycled or recovered. Therefore this product should not be disposed of in your regular trash. Thank you to
return the unit or contact your authorized dealer for more information.
Input voltage level of the amplifier is 240VAC ±5% and please make sure that your local voltage is the same as indicated
on the rear panel. A too low or too high voltage can cause serious damage to your amplifier. In case you find an improper
voltage, please contact our company or your local dealer.
With headphones, do not use it to excessive noise. Otherwise, prolonged listening at high volume levels may cause
permanent damage to your hearing.
When disposing of used batteries, please comply with governmental regulations or rules defined by the public
statements relating to the environment applicable in your country.
Never expose the batteries (battery pack or batteries installed) to excessive heat such as sunshine, fire, etc ...
At the end of its useful life, this product should not be disposed of with regular garbage, but returned to a collection point
for the recycling of electrical and electronic components. This point is emphasized by the symbol on the product, the
instruction manual and on the packaging.
The materials can be reused in accordance with their markings. Through reuse and recycling of raw materials or any
other form of recycling, you make an important contribution to environmental protection. Your municipality can tell you
where is the point of the nearest collection site.
Recommendations
Recycling product
5

Location and precautions
Power sources
Warranty
Avoid placing it in direct sunlight or near a heat source. No source of heat shall be placed on the apparatus. Also avoid
all sources that could cause vibration, dust, cold or moisture. The recommended ambient temperature range is 5-35 °C.
The device must be installed on a stable, level surface. Do not place the unit on an unstable surface or shelf. The unit
may fall, causing serious injury to a child or adult as well as serious damage to the product. Do not place other equipment
on top of the unit.
Due to stray magnetic fields, turntables or CRT TVs should not be located near the unit to avoid possible interference.
The unit should be operated only from the type of power source indicated on the label. If you are unsure of the type of
power available to you, thank you to contact your dealer or the company responsible for the power supply in your area.
Turn off device if you do not intend to use this unit for a long time.
In case of prolonged absence from home, it is recommended to unplug from the electrical outlet.
Make sure each cable is correctly inserted. To prevent hum or background noise, do not mix antenna or other cables
with the power cord or speaker wires.
Keep all packing materials for future use and please fill in the warranty card for registration of warranty.
Your Line Magnetic product is covered by the legal warranty in force in your country. You may also have other rights
which vary from country to country, state to state.
The guarantee of the product is linked to the exclusive use of tubes supplied by the official distributor and in accordance
with the assembly technical specifications.
In addition, you benefit from a commercial guarantee offered by Line Magnetic Australia on the products.
For details on this warranty, please refer to the information available on www.line-magnetic.com.au
6

1Power Switch: ON/OFF. Turn on or turn off the amplifier.
Front panel
Functions descriptions
Input voltage level of the amplifier is 240VAC ±5% and please, make sure that your local voltage is the same as indicated
on the rear panel. A too low or too high voltage can cause serious damage to your amplifier. In case you find an improper
voltage, please contact our company responsible for the power supply or your local dealer.
1
7

Rear panel
1
2
3
Signal input: Inputs (RCA or XLR) are for connecting a preamplifier to your amplifier. It is designed to receive an
analog signal (as opposed to digital signal). To connect your source we are using a traditional RCA cable, they are
usually identified by a color code RED to the RIGHT channel and WHITE to the LEFT channel.
Speaker output: Connect speaker to the terminals.
Important Note: Check the impedance of your speakers. When using a pair of speakers, you can use speakers
with an impedance of between 4, 8 and 16 ohms. BE SURE TO USE THE MATCHING TERMINALS.
Power Socket with main fuse: Main fuse is located on the rear of the amplifier just below the power cord socket.
Replace with the same type and value fuse. Once all connections to the amplifier have been made, connect the
power cable to an electrical outlet and turn on the unit as it is ready for operation.
12 3
0 Ω 4 Ω 8 Ω 16 Ω
SELECTOR
~220V 50Hz 45W
T5AL250V
LM-503 PA
8

Top view
Tubes
V1: 845
V2: 300B
V3: 310A
V4: 5U3C
1
2
3
4
5
HUM BALANCER: Hum adjustment screw for tube V2.
HUM BALANCER: Hum adjustment screw for tube V1.
BIAS CURRENT: Allows to view the tube V1 bias level on the ampere meter when the small handle is down and
when the handle is up, you can see the bias level on the ampere meter for the V2 tube.
BIAS ADJ.: Bias adjustment screws for tubes V1.
N.F.B: Negative Feedback switch - You can choose between two levels of NFB to enjoy the different sound outputs.
1
2
3
Note: Once the bias has been set up
turn Bias Current to ON position you
will read the bias level of V1 tube. If
turned to V1 the bias monitoring will
be turned off.
Bias adjustment / Hum adjustment
WARNING : When making adjustments, be careful not to burn yourself with tubes that are very hot.
Turn on the amplifer and wait for around ten minutes. Choose and turn the Bias Current selector to ON position.
panel and make sure the pointer is at the position showed as in the pictures below (ia=70 mA).
If you have any questions please contact with our company or local service agent.
2010.10.12
4
5
In order to make the machine work condition of the best, it is recommended to use about 150 hours, according to
the above method to test the working state of power tube. Adjustment method: noise when the machine appear hum
noise, adjust the V1, V2 potentiometer noise, and listening to the corresponding channel speaker to minimize noise.
Note: please open the knob on the
lock before the adjustment.
V1 Anode current meter.
9

WARNING: Make sure that the device is not plugged into the mains before making any connections. It is also
recommended to turn off or disconnect all other devices associated while making connections to the product.
Never operate the amplifier without having first connect the loudspeakers. The operation of a tube amplifier is different
from transistor amplifier; without speakers connected, energy is dissipated through the transformers of the amplifier
which will damage the product and reduce it’s useful life.
Check the impedance of your speakers. When using a pair of speakers, you can use speakers with an impedance of
between 4, 8 and 16 ohms. BE SURE TO USE THE MATCHING TERMINALS.
0 Ω 4 Ω 8 Ω 16 Ω
SELECTOR
~220V 50Hz 45W
T5AL250V
LM-503 PA
Speaker connection
1- Unscrew the terminal by hand.
2- Insert the loudspeaker cable (refer to the diagram below).
3- Screw the terminal.
4- Repeat the same operation for the other 3 terminals.
Please notice the polarity of the cable and do not mix up the positive and the negative ends.
Connect the speaker cables with the amplifier after they have been connected to with the speakers.
Make sure that no wires can short the speaker outputs. Make sure that the speaker terminals are tight enough to
ensure a good electrical connection. If the terminal screws are not tight enough, the sound quality may be affected.
Use only dedicated wire to connect the speakers. A section of 1.5 mm² or more is recommended if the cable length is
greater than 3m.
Speaker terminal
Speaker cable or
U-type terminal


10

AC 240V / 50HZ
Use a RCA stereo audio cable (red and white plugs) to connect your sources.
Audio connection
1- During installation please always refer to other product’s operation manuals.
2- Please do not insert the power cord into the main socket until all sources are connected.
3- Rrefers to the Right channel while Lrepresents the Left channel.
Do not also fasten signal cables together with other cables such as power cables to avoid disturbance.
Connection of the power cord
0 Ω 4 Ω 8 Ω 16 Ω
SELECTOR
~220V 50Hz 45W
T5AL250V
LM-503 PA
0 Ω 4 Ω 8 Ω 16 Ω
SELECTOR
~220V 50Hz 45W
T5AL250V
LM-503 PA
11

Turning on
IMPORTANT - BEFORE TURNING ON THE AMPLIFIER
Please make sure corresponding voltage is the same as required. We are not responsible for damage caused by misuse
of unsuitable voltage.
Make sure all connections (first, connect the speaker cables, then the cables from your sources, and plug the power
cable into the AC outlet) are valid, and the stability of your power supply AC 240V - 50Hz.
Startup procedure
1- Set the VOLUME of the amplifier to zero (potentiometer totally on the left).
2- Switch the amplifier to ON position via the POWER switch located on the side of the amplifier.
The LED lights up in orange on the front panel of the amplifier. It indicates that the amplifier is working.
3- After 30 seconds, the orange led blinking will stabilize to indicate that the amplifier is ready for use.
4- Select the source you want to listen to with the SELECTOR button located to the right of the front panel.
5- Adjust the VOLUME knob as you like to enjoy your music.
WARNING : Please make sure corresponding voltage is the same as required. We are not responsible for damage
caused by misuse of unsuitable voltage.
General observations
-
-
-
-
-
-
It is normal that power transformer becomes hot for extended period of operation.
Unplug the product during lightning storms or when not in use for a long time.
To prevent damage to the amplifier never disconnect the speaker cables while the unit is ON.
In order to protect the tubes please re-switch on the amplifier after turned off in two minutes.
This product is designed and manufactured with our original parts for reaching the best results. We are not responsible
for problems and damages caused to the amplifier by non-original replacement parts.
Line Magnetic Audio reserves the right to change specifications at any time without further notice in advance if products
are upgraded. Specifications on the manual only show the specifications of the amplifier you’ve bought.
12

Tube replacement
Maintenance
WARNING
Cleaning
1. Use soft dry cloth to clean the amplifier.
2. Refer to the safety precautions if you are going to use chemically treated cloth for cleaning.
3. Use a soft cloth with neutral detergent first and then wipe with a dry cloth.
As a precaution, it is best to unplug the unit before handling and ensure the heat generated by the product has
been properly dissipated.
Basics tubes Common replacements
5U3C 2748, 5931
310A Soviet Union/om12C, WE 310A
300B 300B, 300A, 4300B
845 845 A/B/C
13

Problem Cause Solution
Power LED is OFF. Power cord is not well-connected. Please check the power cable connection or power
outlet connection.
Main fuse is out. Replace with the same type and value fuse.
Troubles of inner parts or
components.
Please contact your local dealer.
Power LED is ON. Volume is at zero. Turn up the Volume.
No signal input. Check the function of the sound source.
Check the input connectors and/or switch to the
proper input
Sound distortion. High input signal level. Turn down the volume to suitable position.
Replace the signal input cable.Damaged signal cable.
Noise output. Ground of input signal cable is open
or bad contact of the input signal
cable.
Replace the input signal cable with a new one.
Components or circuits are in trouble. Please contact your local dealer.
Stereo image is not so
good.
Signal input cables or speaker cables
are wrongly connected.
Reconnect it as suggested in the manual.
No reaction to the remote
control.
Disturbed by external devices. Keep away from the disturbance (ie: microwave
oven) and restart the amplifier.
Batteries of the remote control are
low.
Please replace the batteries.
Obstacle is located between the
remote control and the amplifier.
Move the object that blocks the IR rays between
the remote control and the IR sensor located on the
front of the amplifier.
.
Please follow the instructions in this manual to keep the amplifier working in a reliable and safe manner.
Sometimes problems could be caused by other related equipment, please check the connections.
If you experience a problem with this unit, please check the following items before requesting service. If it still does not
operate correctly, contact the retailer where you purchased the unit.
For repair, during or after the warranty, please contact your local dealer.
Troubleshooting
The LM-503PA is designed and manufactured with our original parts to achieve the best results. Line Magnetic is not
responsible for problems or damage caused by non-original parts being used in the unit.
Line Magnetic is not responsible for any problems caused by checking or opening the unit without the permission of the
company or dealer. For service, please contact your local Line Magnetic dealer or Line Magnetic Australia.
14

Line Magnetic Australia Pty Ltd
Email: [email protected]
www.line-magnetic.com.au