Linear Technologie LINEARLEDS LYRE LTL.LY712E User manual

Linear Technologie • 11 rue du Puits Rochefort • 42 100 Saint-Etienne
Tél: [phone] • Fax: [phone] • www.lineartech.fr V.2017
LED LYRE 7x12 WATTS LTL.LY712E
Operation manual
Keep this manual for futur uses.

2
TABLE OF CONTENTS
1. About this product
2. Safety instructions
3. Operation instructions
4. Product description
5. Product views
6. Placing
7. DMX-512 connections
8. Mounting
9. Manual
10. Specications
11. Play
Page 3
Page 3
Page 3
Page 4
Page 4
Page 4
Page 4
Page 5
Page 5
Page 6
Page 6

3
3. OPERATION INSTRUCTIONS
- This automatic projector is controlled to create decorative e󰀨ects, for indoor use
- Don’t turn on the xture if it’s been through severe temperature di󰀨erence like after transportation
because it might damage the light due to the environment changes. So make sure to operate the
xture until it is in normal temperature.
-This light should be keep away from strong shaking during any transportation or movement.
-Don’t pull up the light by only the head, or it might cause damages to the mechanical parts.
-Don’t expose the xture in overheat, moisture or environment with too much dust when installing it.
And don’t lay any power cables on the oor. Or it might cause electronic shock to the people.
-Make sure the installation place is in good safety condition before installing the xture.
-Make sure to put the safety chain and check whether the screws are screwed properly when
installing the xture.
-Make sure the lens are in good condition. It’s recommended to replace the units if there are any
damages or severe scratch.
-Make sure the xture is operated by qualied personnel who knows the xture before using.
-Keep the original packages if any second shipment is needed.
-Don’t try to change the xtures without any instruction by the manufacturer or the appointed repairing
agencies.
-It is not in warranty range if there are any malfunctions from not following the user manual to operate
or any illegal operation, like shock short circuit, electronic shock, lamp broke, etc.
1. ABOUT THIS PRODUCT
Thank you for choosing our moving head. For your own safety, please read this manual before
installing the device. This manual covers the important information on installation and applications.
Please install and operate the xture with following instructions. Meanwhile, please keep this manual
well for future needs. This moving head wash is made of a new type of high temperature strength of
engineering plastics and cast aluminum casing with nice outlook. The xture is designed and
manufactured strictly following CE standards, complying with international standard DMX512
protocol. It’s available independently controlled and linkable with each other for operation. And it
is applicable for large-scale live performances, theater, studio, nightclubs and discos. Adapts with
powerful LED lamps which features high brightness and stability. Please carefully open package
when you receive the xture and check whether it is damaged during the transportation.
2. SAFETY INSTRUCTIONS
This device has left the factory in perfect condition. In order to maintain this condition and to ensure
a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this user manual. If the device has been exposed to temperature changes due to
environmental changes, do not switch it on immediately. The arising condensation could damage
the device. Leave the device switched o󰀨 until it has reached room temperature. This device falls
under protection-class I. Therefore it is essential that the device be earthed. The electric connection
must carry out by qualied person. The device shall only be used with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual. Make sure
the power cord is never crimped or damaged by sharp edges. If this would be the case, replacement
of the cable must be done by an authorized dealer. Always disconnect from the mains, when the
device is not in use or before cleaning it. Only handle the power cord by the plug. Never pull out
the plug by tugging the power cord. During initial start-up some smoke or smell may arise. This is
a normal process and does not necessarily mean that the device is defective, it should decrease
gradually. Please don’t project the beam onto combustible substances. Fixtures cannot be installed
on combustible substances, keep more than 50cm distance with wall for smooth air ow, so there
should be no shelter for fans and ventilation for heat radiation. If the external exible cable or cord of
this xture is damaged, it shall.

4
• CH1 : Pan 0 - 225
• CH2 : Tilt 0 - 255
• CH3 : Pan ne
• CH4 : Tilt ne
• CH5 : No function
• CH6 : Strobe
• CH7 : Dimmer
• CH8 : Red
• CH9 : Green
• CH10 : Blue
• CH11 : White
• CH12 : Macro colors
5. PRODUCT VIEWS
6. PLACING
WARNING : Put o󰀨 the supply before change a fuse !
REPLACE A FUSE :
Use a plate screwdriver to put out the fuse and replace with a same fuse. Put on the power.
7. DMX512 CONNECTION
• 12 DMX512 channels
• Pan 540° / Tilt 180°
• Variable strobe
• Variator (0-100%)
• RGBW colors
• DMX512 control, master – slave
DMX 12 channels resum :
4. PRODUCT DESCRIPTION

5
8. MOUNTING
Note : Clamp sold separately
It is important that the device fan do not be obstructed. Fix the lyre with the help of clamp.
Adjuste the angle as you want.
9. MANUAL
Control pannel
Access to the control pannel in use the display buttons placed under the LCD display.

6
• CH1 : Pan
• CH2 : Tilt
• CH3 : Pan ne
• CH4 : Tilt ne
• CH5 : No use
• CH6 : Strobe
• CH7 : Dimmer
• CH8 : Red
• CH9 : Green
• CH10 : Blue
• CH11 : White
• CH12 : Macro colors
In select a function, the display shows the rst available option.
Press repeatedly on <MODE/ESC> to reach the menu you want. Use <UP> and <DOWN>
buttons to navigate into the menu options. Press <ENTER> to select the option you want.
MENU
10. SPECIFICATIONS
Dimensions : 300 x 240 x 240 mm
Weight : 3.8 kg
Power supply : 120V 60 Hz AC or 230V 50 Hz
Fuse : 3A 250V
LEDS : 7x12W RGBW
Opening angle : 25°
Pan 540° Tilt 180°
12 DMX channels
Protocol DMX512 USITT
1 ADD (address setting) : A001 -A512
2 PAN (panoramic inversion)
3TILT (tilt inversion)
4 PLAY (automatic program)
5DISP (AT01, AT02, SN01, SN02, SLAVE, DNCO)
6 TEST
11. PLAY
DISP : Press successively on Enter, Enter, Up and Enter
Inverst : Press successively on Enter, Enter, Down and Enter

Linear Technologie • 11 rue du Puits Rochefort • 42 100 Saint-Etienne
Tél: [phone] • Fax: [phone] • www.lineartech.fr