Lite the Nite LiteMountA LiteTouch User manual

55-110"
139-278cm
Max
[275Ibs]
Landscape VESA Max 800*600
Portrait VESA Max.400*600
LiteTouch and LiteTouch PRO
Wall Mount
LiteMountA
2016 LiteThe Nite Technologies, LLC All Rights Reserved
C

TM
Thank you for choosing the Lite Touch and Lite Touch Pro wall
mount for your display panel installation.
The mount can be configured in landscape or portrait orientation.
To install your panel in landscape orientation,complete steps 1
thru 8 of this manual.
To install your panel in portrait orientation, complete steps 10 thru 15.
TM
1.Assemble the wall bracket for a landscape or portrait installation
2.Mount the wall bracket at the desired mounting location
3.Attach the panel brackets to the display panel
4.Lift the panel onto the top rail of the wall bracket
5.Snap the bottom of the panel onto the wall bracket
6.Level the display panel using the lateral adjustment screws
Installation Overview

2PCS 1PCS 1PCS 1PCS
VESA MAX 800X600
1
600
800
B
A C D
E F G
M6X15
4PCS
M5X15
4PCS
M8X15
4PCS
M10X15
4PCS
10X70
8PCS
12X70
8PCS
M6
4PCS
M5
4PCS
M8
4PCS
M10
12PCS
8mm
1PCS
6mm
1PCS
5mm
1PCS
17mm
1PCS
14mm
1PCS
4mm
1PCS 15X8X15
4PCS
Panel Bracket Left Wall Mount Bracket Center Wall Mount Bracket Right wall Mount Bracket
Landscape Installation
Below is an example of the assembled wall mount
bracket configured for alandscape installation

2
3
C
Solid Brick and Concrete Block Landscape Mounting
Assemble The Wall Mount Bracket
Attach the center wall
mount bracket to the
left wall mount bracket
and right wall mount
bracket using washers
(D) and nuts as shown
A. Drill a 15/32" hole 2 3/4" deep at
each of the mounting locations and
insert the plastic anchors (C)
B. Attach the wall mount bracket to
the wall using screws(B) and washers(D)
NOTE:
Attach the wall mount bracket using at
least 8 screws

4
DB
Wood Stud Landscape MountingWall
A. Locate the wood studs in the wall and
mark the stud centers. Be sure to attach
wall mount to at least 2 studs
B. Drill a 3/16" pilot hole at each of the
mounting locations in the center of the stud
C. Attach the wall mount bracket to the
wall using screws(B) and washers(D)

5
E
G
A
D
Correct Correct Incorrect
A. Install the panel brackets to the
rear of the display panel with the
“hook”up as shown below using
screws (A) and washers(D). Tighten
screws (A) with allen wrench(E)
NOTE:
Install spacers(G) if your
display panel has a recessed back.
Be sure the mount is attached as
shown
D
Attach The Panel Brackets To The Display Panel
Hook

Wall
Display Panel
7
6Attach The Display To The Wall Mount
Level The Display Panel Level the display panel using a long
phillips screwdriver to turn the lateral
adjustment screws in the top of panel
brackets as shown below
Tip:
Raise the low side of the display panel first
NOTE:
This step should be completed with 2 people
due to the weight of the display panel
A. Lift the display panel above the wall mount
and lower the panel bracket hooks onto the
top of the wall mount
B. Push the bottom of the display toward the
wall mount until it “snaps” into place
C. If the quick release strings are hanging
beneath the display panel, place the
magnetic knobs on the mount to keep
the strings out of sight
Magnetic Knob

8Adjust Display Panel Tilt
Congratulations! Your wall mount installation is complete
-5-+10
Adjust the display panel tilt from -5 degrees to +10
degrees as desired. Grasp the display panel at the top
and bottom and move it to the desired angle. Tighten
or loosen the Tilt Adjustment Knobs as needed.
Tilt Adjustment Knob

9How To Remove The Display panel From The Wall Mount Bracket
Display Panel Quick Release
NOTE:
This should be completed with 2 people due to the weight of the
display panel
A. Pull down on both display panel quick release cables simultaneously while pulling
the bottom of the display panel away from the mounting bracket
B. Pickup the display panel until it is free from the wall mount

600
400
VESA MAX 400X600
Portrait Installation
11
10
70mm
Φ12mm
Mount to the concrete wall
Solid Brick and Concrete Block Portrait Mounting
CDB
Below is an example of the
assembled wallmount bracket
configured for a portrait
installation using the left wall
mount bracket
A. Drill a 15/32" hole 2 3/4" deep at
each of the mounting locations and
insert the plastic anchors(C)
B. Attach the wall mount bracket to
the wall using screws(B)and washers(D)