Lithe Audio 06300 User manual

15
CAUTION:DO NOT EXCEED
RATED LISTEDWEIGHT.SERIOUS
INJURY OR PROPERTY DAMAGE
MAY OCCUR!
60"
MAX
200x200
300x300
400x200
400x400
40kg
(88lbs)
RATED
OK
OK
LEARN MODE instructions as shown below:
STEP1: Press and hold for 5 seconds until LED light on the matched remote control stays on, and
then press .The buzzer will sound once, the red LED light on the IR receiver will stay on,then the
LEARNMODE willbe entered.
STEP2: If LEARN , please press on the matched remote control until the buzzer sounds twice,
the red LED light on the IR receiver will change from being steady to a slow flash.
STEP3:Aim the TV remote at the IR receiver,and press the button on theTV remote that you need to set as
the function of button until the buzzer sounds three times.the red LED light on the IR receiver will
change from slow flash to a fast flash.
STEP4: Press button on the matched remote control until the buzzer sounds four times.The
red LED light on the IR receiver will turn off. button will be LEARNED successfully. If the buzzer only
sounds once, then a LEARN failure.(The TV remote won’t support the LEARNING function).
(Pleasefollow step1 through step4 in turn if the user need to LEARN more buttons)
Learn “Power” button on the TV remote:
Press and hold for 5 seconds until LED light on the matched remote control stays on , and then press .
The buzzer will sound once, the red LED light on the IR receiver will stay on,then press and hold button
on the matched remote control until the buzzer sounds twice,then release the button.The red LED
light on the IR receiver will change from being steady to a slow flash.
Aim theTV remote at the IR receiver, and press “Power” button.The buzzer will sound three times.The red
LED light on the IR receiver will change from slow flash to a fast flash.Press button on the matched
remote control until the buzzer sounds four times.The red LED light on the IR receiver will turn off.“Power”
button will be LEARNED successfully. If press “power” button, theTV wall mount will automatically reset.
Note:When there is no activity for over 20 seconds in any step .TV remote will automatically exit from the
LEARN MODE.
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your distributor if you have any questions.
OK
OK
40kg
(88lbs)
RATED
INSTALLATION MANUAL
REMOTE CONTROL MOTORIZED
90OWALL MOUNT 32-60"

21
NOTE: Read the entire instruction manual before you start installation and assembly. Component Checklist
WARNING
IMPORTANT:Ensure that you have received all parts according to the component checklist prior to installation.
If any parts are missing or faulty,telephone your local distributor for a replacement.
Package M
adapter bracket (x2)
D
PackageW
ST6.3x55 (x5)
W-A
concrete anchor (x5)
W-B
D6 washer (x3)
W-C
motorized wall mount (x1)
A
M5x14 (x4)
M-A
M6x14 (x4)
M-B
washer (x4)
M-F
M8x20 (x4)
M-C
big spacer (x4)
M-H
M6x30 (x4)
M-D
M8x30 (x4)
M-E
small spacer (x8)
M-G
cable clip (x2)
C
wall template (x1)
B
remote control (x1)
F
power supply (x1)
G
• Do not begin the installation until you have read and understood all the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instructions or warnings,please contact your local distributor.
• This mounting bracket was designed to be installed and utilised ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
•This product should only be installed by someone with good mechanical ability
who hasbasic building experience and fully understands this manual.
• Make sure that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
• If mounting to wood wall studs,make sure that mounting screws are anchored
into the center of the studs.The use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
the equipment.
·Tighten screws firmly, but do not over tighten. Over tightening can cause damage
to the items,This greatly reduces their holding power.
•This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
• Please do not disassemble or change the electronic components of the product
without authorization.
IR receiver (x1)
E
bubble level (x1)
H

The swing arm needs to be adjusted
according to the size ofTV.
X= L/2+260(mm)
L:The length ofTV
Remove the screws and washers using
the proper phillips screwdriver.
WARNING
• Make sure that mounting screws are anchored into the center of the studs.The use of a stud
finder is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined weight of the
equipment and all attached hardware and components.
4a.ForWood StudWall Mounting
Drill pilot holes
3
X X
√
2
1
Find and mark the exact
location of mounting holes
3
W-A
X
7mm
4
X
X
X=TV(L)/2+260mm
W-A
7mm
2.Opening Hard the Swing Arm
1.Separating the Decorative Covers from the Wall Mount
3 . Position the Swing Arm
90°
Reinstalling the screws and washers to secure
the swing arm after finishing the adjustment.
Reverse installation
Forward installation
Tighten the screw leaving a 7mm space
from the wall.
H
H

56
X X
√
Installers must verify that the supporting surface will safely support the combined weight of
the equipment and all attached hardware and components.
WARNING
4b.For Solid Brick and Concrete Mounting
Drill pilot holes
2
1
Mark the exact
location of
mounting holes
W-A
W-B
7mm
W-A
W-B
W-C W-A
X X
√
Screw the wall
mount onto
the wall
Reverse installation
Forward installation
Tighten the screw leaving a 7mm space
from the wall.
H
H
H
7mm

87
5.Installing the Decorative Covers and the Cable Clips
C
X X
√
Screw the wall
mount onto
the wall
H
W-C W-A

109
or
6-2 For Recessed Back Screens or toAccess A/V Inputs
TV
TV
TV
Tighten all screws but do not over tighten.
· Screw the adapter brackets onto theTV.
· Position the adapter brackets as close as possible to the middle of the screen.
Note:Choose the appropriate screws,washers and spacers (if necessary) according to the type of screen.
or or
M-C/M-D/M-E
M-F
M-G
M-G
M-D/M-E
M-F
M-H
M-D/M-E
M-F
M-G
M-H
6-1 For Flat Back Screens
TV
TV
TV
6 . Installing the Adapter Brackets
M-A
M-B
M-C
M-F
Remove the screws on the adapter brackets
and keep the screws for later use.

12
11
8. Cable Management
Connect the cables to yourTV and route through the cable clips.
Note: Leave slack in the cables for arm movement.
90°
or
90°
or
7. Hooking the TV onto the Wall Mount
Hook the TV over the swing arm.
Reinstall the bottom screws to secure the adapter brackets to the swing arm.
Important:Make sure the TV is correctly hooked before releasing the TV.
To avoid the little tilt caused by weight,you can tighten the
adjustment screws to help level theTV.
H

Buttons function instructions
LEARN MODE operation instructions
The loss of matched remote control would result inTV wall mount being unusable.The LEARN MODE is
used to learn how to useTV remote (ONLY suitable for theTV remote of popular brands.) to control TV
wall mount.
Note:
•TV remote can’t replace the all functions of matched remote control.Only LEARNING the three buttons
functions.With , and respectively.
• The user must follow the rules below when using theTV remote to control TV wall mount.
Select the alternate buttons from theTV remote, and the button that can't direct control theTV.
•If you need to erase all the button functions LEARNED, press and hold for 4 seconds and repeat
five times.
If you don't erase them,the new button functions LEARNED every time will overwrite the last button
functions LEARNED.
OK
1413
10.The Remote Control Operating Instructions
Remote control operation instructions
STEP 1: When powered, the buzzer sounds once beep,TV wall
mount will be in standby state.
STEP 2:Forward and reverse installation choices (NOTE 1:
There are forward and reverse installations for theTV wall
mount.Swinging the TV wall mount to right against the wall
that defaults to the forward installation.If it is the forward
installation, the STEP 2 is not required; If it is the reverse
installation,Press and hold for 5 seconds until the buzzer
sounds twice beep beep,Remote control is now successfully
set. NOTE 2: TheTV wall mount provides 0°(be parallel to wall)
and 90º of lateral rotation (be perpendicular to wall).TV wall
mount has been set before they go out (Please don’t set it
without special requirement).If you want to reset the swing
angle to 0°and 90º.Press and hold for 5 seconds and
repeat four times.The system will start automatic positioning:
First positioning TV wall mount with flat against the wall, then
positioning TV wall mount with 90°of lateral rotation until theTV
remote control
9 . Placing the IR Receiver
Peel the backing paper. Place the IR receiver into desired position.
Make sure nothing will obstruct the transmission from where theTV will be viewed.
Do not plug into the power outlet until it is ready to be operated.
Do not open the electrical cover please.
G
E
Stop button
OK
Memory button1.Press and hold for 5 seconds,the buzzer will sound twice beep beep,LED light
will turn on for 1second,The memory is saved as location 1.
Memory button2.Press and hold for 5 seconds,the buzzer will sound twice beep beep,LED light
turn on for 1second,The memory is saved as location 2.
Forward and reverse installation choices button (Pressing the button is invalid once in the working
condition).
+Learning button,Please read the instructions below for more info.
+To recall the button(location 1). Press and release button, and then press button,
The TV wall mount will automatically swivel to the location1 after the buzzer sounds once.
+To recall the button(location 2). Press and release button, and then press button,
The TV wall mount will automatically swivel to the location2 after the buzzer sounds once.
The left button.Press and release , theTV wall mount will swivel to the left until is pressed
or theTV wall mount swing to 90 degrees to stop.
OK
The right button. Press and release , the TV wall mount will swivel to the right until is pressed
or theTV wall mount swing to 0 degrees to stop.
OK
Follow the Key function instructions below to operate.
wall mount automatically stop at 90°position.)
STEP 3:Press and release OK to return theTV wall mount flat against the wall and hear one beep
from the buzzer, the system will then enter a working condition.