Litheli U1GT21000 User manual

Visit our website at: http://www.litheli.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Operator's Manual
Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
Save This Manual
40V BATTERY POWERED
STRING TRIMMER
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please contact us: WWW.LITHELI.COM.
U1GT21000
Copyright 2019 Litheli. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Litheli.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
©

Watch what you are doing. Use
common sense. Do not operate appliance when
you are tired.
It will do the
job better and with less likelihood of injury
at the rate for which it was designed.
Do not use appliance
for any job except that for which it is intended.
Use face or dust mask if
operation is dusty.
Do not wear loose
clothing or jewelry. They can be caught
in moving parts. Use of rubber gloves
and substantial footwear is recommended
when working outdoors. Wear protective
hair covering to contain long hair.
Page 2 WWW.LITHELI.COM Item U1GT21000
Table of Contents
Safety ......................................................... 2
Specifications
.............................................
5
Setup
..........................................................
6
Operation
.................................................
10
Maintenance .................................................. 12
Parts List and Diagram .............................. 14
Warranty
..........................................................
16
WARNING SYMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMPORTANT SAFETY INSTRUCTIONS
When using electric gardening appliances, basic safety precautions should always be followed
to reduce the risk of fire, electric shock, and personal injury, including the following:
READ ALL INSTRUCTIONS
Gardening Appliance Safety
1. Avoid Dangerous Environment -
Do not use appliances in damp or wet locations.
2. Do Not Use In Rain.
3. Keep Children Away -All visitors should
be kept at a distance from work area..
4. Dress Properly -
5. Wear ANSI-approved safety goggles,
hard hat and heavy-duty rubber work
gloves.
.
6. Wear thick jeans and steel-toed
work boots to help prevent injury
caused by flying debris.
7. Use Right Appliance -
8. Avoid Unintentional Starting -
Do not carry appliance with finger on switch.
9. Don’t grasp the exposed cutting blades or cutting
edges when picking up or holding the appliance.
10. Do Not Force Appliance -
11. Do not Overreach -
Keep proper footing and balance at all times.
12. Stay Alert -
13. Store Idle Appliances Indoors - When not in use,
appliances should be stored indoors in dry, and
high or locked-up place - out of reach of children.

Before further use of
the appliance, a guard or other part that is
damaged should be carefully checked to
determine that it will operate properly and
perform its intended function. Check for
alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other
condition that may affect its operation. A guard
or other part that is damaged should be properly
repaired or replaced by a qualified technician
unless indicated elsewhere in this manual.
Keep cutting
edge sharp and clean for best performance and
to reduce the risk of injury. Follow instructions
for lubricating and changing accessories. Keep
handles dry, clean, and free from oil and grease.
Page 3
14. Maintain Appliance With Care -
15 . Check Damaged Parts -
16. Keep guards in place and in working order..
17 . Keep hands and feet away from cutting area..
18 . Wear full eye protection and protective
clothing.
19. If electrolyte contacts the skin, wash
it off immediately with water..
20. If electrolyte contacts the eyes, flush thoroughly and
immediately with water. Seek medical attention.
21 . Stop working when you feel tired or exhausted.
Make regular breaks to rest..
22. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
23. When servicing use only identical
replacement parts.
24. Disconnect Appliance - Remove Battery Pack
when not in use, before servicing, when changing
accessories such as blades, and the like.
25. Carefully follow cutting procedures
explained in this manual.They are specifically
planned to reduce risk to the operator..
26. Only replace the line on this appliance with
the line material and diameter of line listed
on the Specifications table. Other materials,
such as wire, rope, or blades can damage the
appliance and be forcefully and dangerously
ejected from the appliance upon breaking.
Lithium Battery Safety Warnings
LITHIUM BATTERIES STORE
ALARGEAMOUNTOFENERGY AND
WILL VENT FIRE OR EXPLODE IF MISTREATED:
1 . Keep
Battery Pack dry.
2. DO NOT DO ANY OF THE FOLLOWING
TO THE BATTERYPACK:
a. Open,
b. Drop,
c. Short-circuit,
d. Puncture,
e. Incinerate,
f. Expose to temperatures greater than 104°F.
3. Charge Battery Pack only according
to its Charger’s instructions..
4. Inspect Battery Pack before every use;
do not use or charge if damaged..
Battery Charger Safety
1 . SAVE THESE INSTRUCTIONS - This manual
contains important safety and operating
instruction for battery charger Model U1GT21000.
2. Before using battery charger, read all instructions
and cautionary markings on battery charger,
battery, and product using battery..
3. CAUTION - To reduce risk of injury, charge only li-ion
type rechargeable batteries. Other types of batteries
may burst causing personal injury and damage.
4. Do not charge or use appliance in rain, or in wet
locations.
5. Do not use battery-operated appliance in rain.
6. Remove or disconnect battery after use,
before servicing, cleaning or removing
material from the gardening appliance..
7. Do not dispose of battery in a fire. The
cell may explode. Check with local codes
for possible disposal instructions.
8. Do not open or mutilate the battery. Released
electrolyte is corrosive and may cause damage to
the eyes or skin. It may be toxic if swallowed.
9. Exercise care in handling batteries in order not
to short the battery with conducting materials
such as rings, bracelets, and keys.. The battery
or conductor may overheat and cause burns..
WWW.LITHELI.COM
Item U1GT21000

Page 4
Vibration Hazard
This appliance vibrates during use.
Repeated or long-term exposure to vibration may
cause temporary or permanent physical injury,
particularly to the hands, arms and shoulders.
To reduce the risk of vibration-related injury:
.
1 . Anyone using vibrating appliances regularly or for
an extended period should first be examined by
a doctor and then have regular medical checkups
to ensure medical problems are not being caused
or worsened from use. Pregnant women or people
who have impaired blood circulation to the hand,
past hand injuries, nervous system disorders,
diabetes, or Raynaud’s Disease should not use this
appliance. If you feel any symptoms related to
vibration (such as tingling, numbness, and white
or blue fingers), seek medical advice as soon as
possible.
2. Do not smoke during use.. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury..
3. Wear suitable gloves to reduce the
vibration effects on the user.
4. Use appliances with the lowest vibration when
there is a choice between different processes.
5. Include vibration-free periods each day of work.
6. Grip appliance as lightly as possible
(while still keeping safe control of it).
Let the appliance do the work.
7. To reduce vibration, maintain the appliance
as explained in this manual. If any abnormal
vibration occurs, stop use immediately.
General Safety
1. The spool will continue to rotate for a few
seconds after use. Allow it to stop completely
and remove Battery Pack before putting the
appliance down, making any adjustments, or
servicing the appliance.
2. Do not use in rain, snow, sprinklers, or wet grass..
Do not rinse off the Trimmer..
3. Use only during daylight hours..
4. Carefully inspect the spool housing and guard
before inserting Battery Pack in the Trimmer. Do
not use Trimmer if any part is cracked or damaged.
5. Do not use appliance for other than intended use.
6. Maintain labels and nameplates on the appliance.
These carry important safety information.
If unreadable or missing, contact Litheli for a
replacement.
7. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
SAVE THESE INSTRUCTIONS.
WWW.LITHELI.COM Item U1GT21000

NOTE :
Page 5
Specifications
Charger Input Rating
Charger Output Rating
Battery Rating
Battery Type
No Load Speed
Replacement Line Type
Grounding
TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECTGROUNDING:
Check with a qualified electrician if you are in doubt as to whether the outlet is properly
grounded. Do not modify the power cord plug provided with the charger. Do not use the charger
if the power cord or plug is damaged. If damaged, have it repaired by a service facility before
use. If the plug will not fit the outlet, have a proper outlet installed by a qualified electrician.
WWW.LITHELI.COM
Item U1GT21000
120VAC / 60Hz
36VDC / 3.3A
40VDC / 2.5Ah / 90Wh
40V Litheli Li-Ion
7500rpm 10%
0.062" Nylon
ExtensionCords
Extension cords must not be used with this item’s Charger..
Symbology
Double Insulated
VVolts
~Alternating Current
AAmperes
n0 xxxx/min. No Load Revolutions per Minute (RPM)
WARNING marking concerning Risk
of Eye Injury. Wear ANSI-approved
safety goggles with side shields.
Read the manual before
set-up and/or use.
WARNING marking
concerning Risk of Fire.
Do not cover Charger
ventilation ducts.
Charge on fireproof surface only.
WARNING marking concerning
Risk of Electric Shock.
Properly connect Charger’s power
cord to appropriate outlet.
WARNING marking concerning
Risk of Explosion.
Do not puncture, short, or open
battery packs and do not charge
damaged battery packs.
Do not throw the batteries in the
household waste, fire or water.
Do not expose the battery to sunlight
for a long time and do not place it on
radiators (max. 45 ° C).
Dispose of the batteries at a collection point
for old batteries, from where they are taken
to environmentally friendly recycling.
Charge level indication.
Indication of the noise level
LWA in dB.
Charge level indication.

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or this product.
Page 6
Setup - Before use:
Functions
Edge Guide not shown.
WWW.LITHELI.COM Item U1GT21000
Spool Storage
Compartment
Trigger
Trigger
Safety Lock
Auxiliary
Handle
Extension
Lock Extension
Tube
Head Angle
Button
Guard
Line
Cutter
Edger/Trimmer
Button
Edger
Wheels
Spool
Housing

Page 7WWW.LITHELI.COMItem U1GT21000
Charging the Battery Pack
NOTE : The Battery Pack comes partly charged.
Charge the Battery Pack prior to first use, ideally at least 60 minutes.
Rapid Battery Charger
Power Cord
with Plug
Battery
Pack
Connector
Charging
Status
LED – Red
Charging
Status
LED – Green
Always pull out the Power Plug of the Charger
from the mains before removing or connecting the Battery Pack to the charger.
Never charge the Battery Pack when the ambient temperature is below 10 °C or above 40 °C.
Rest the Charger for at least 15 minutes between successive charging sessions.
If no Battery Pack is inserted into the Charger and the
charger is connected to mains, the Charging Status LED flashes green.
1 .
2.
3.
4.
Align the Battery Pack to the rails of the
Charger and slide it in. Ensure it clicks
noticeably in place.
Connect the Power Plug of the Charger with
the mains. The Charging Status LED lights
up red. The continuously lit green
Charging Status LED indicates
that the charging process is complete.
Disconnect the Power Plug of the
Charger from the mains and remove the
Battery Pack from the charger.
Attach the Battery Pack back to the
product (see “Installing and Removing
Battery Pack”).
Charging status LEDs
Green LED flashes
without battery pack Charger ready
Green LED lights up
with battery pack
Battery pack fully
charged
Red LED lights up with
battery pack Battery pack charging
Red and green LEDs
flashing Battery pack defect
Red and greenLEDs
continuously lit
Battery pack too cold
or warm

WARNING! TO PREVENT SERIOUS
INJURY FROM FLYING DEBRIS: Install the
guard only in the orientation shown.
NOTE :
Page 8
Assembly Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Release Trigger of the appliance before performing any procedure in this section.
For additional information regarding the parts listed in the following pages,
Install Guard
guard
1 . Attach Guard to bottom of String
Trimmer with two included Screws.
2. Remove protective tape covering Line Cutter..
NOTE : Line Cutter is set to 12" cutting width..
3. To change the spool, remove Line Cutter
Screw, rotate Line Cutter, then replace Screw..
WWW.LITHELI.COM Item U1GT21000
Screws
Line
Cutter
Screw
Guard
Line
Cutter
Protective
Tape
refer to the Assembly Diagram near the end of this manual.
Battery Pack
Release
Button
Battery Level
Indication Lights
Battery
Level Button
Checking the Battery Charging Level
Press the Battery Level Button
to check the charging level of the Battery Pack. The charging level
will be shown on the Battery Level Indication Lights.
Charge the Battery Pack before
operation when it is at 25% or low battery charging level.
NOTE :
Charging level
Charging level too low
Between 5% and 50%.
Between 50% and 80%.
More than 80%.
LED status

Install Auxiliary Handle
1 . Slide Auxiliary Handle up on to Auxiliary
Handle Bracket until it clicks into place.
2. To change Auxiliary Handle position, move
Auxiliary Handle Lock up, change handle position,
then move Auxiliary Handle Lock down.
Page 9
Install Edge Guide
1 . Spread Edge Guide arms apart, then
push ends into holes on housing..
2. Use the Edge Guide to limit striking
objects with the Line while trimming
nearby.
3. Flip the Edge Guide up out of
the way when not in use.
Install Edger Wheels
1 . Slide Edger Wheels into slot. Push down
until Edger Wheels lock into place.
.
2. Remove Edger Wheels by pushing Tab
and pulling up on Edger Wheels.
WWW.LITHELI.COM
Item U1GT21000
Auxiliary
Handle
Auxiliary
Handle
Bracket
Auxiliary
Handle Lock
Edge
Guide
Arm
Hole
Edger
Wheels
Slot
Tab

Do not charge a cracked,
open, or leaking Battery Pack, or charge a
non-recommended type of Battery Pack.
While charging, Battery Pack and
Charger may become warm to the touch and the
Charger′s fan may come on. This is normal.
Page 10
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
TO PREVENT SERIOUS INJURY:
Before operating the gardening appliance, put on ANSI-approved safety goggles, closed-toe work
boots, long pants, and other safety gear. Safety goggles and other safety gear are purchased by
yourself.
TO PREVENT SERIOUS INJURY AND PROPERTY DAMAGE:
Inspect the area before using the String Trimmer. Remove all hard objects from work area.
Use both hands when operating Trimmer.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Charging Battery Pack
1 . Place Battery Charger on a dry, flat,
fireproof surface indoors.
NOTE : Allow battery to cool completely before charging.
2. Examine Battery Pack.
3. Battery Pack is designed to fit this Charger
specifically. If Battery Pack does not fit
Charger properly, do not try to insert it. Do
not force Battery Pack into the Charger.
4. Plug Charger into a grounded, 120VAC, 60Hz
receptacle. Green LED will blink, showing
that power is supplied to the charger.
5.
NOTE : A fully discharged Battery Pack will
take about 1 hour to fully charge.
NOTE :
6. Green LED will light continuously when
Battery Pack is charged. Unplug Charger
and remove Battery Pack when finished.
7. Allow Battery Pack to cool completely before
use.
.
Installing and Removing Battery Pack
1 . To install: Slide Battery Pack into slot on back
of String Trimmer until it clicks into place.
2. To remove: Press both Battery Pack Release
Buttons and pull Battery Pack out of slot.
WWW.LITHELI.COM Item U1GT21000
Battery
Pack
Battery Pack
Release
Buttons
Make sure that the Power Switch/Trigger is in the off-position and
remove Battery Pack before setting up the appliance.
Slide Battery Pack onto Charger. Red LED
will light continuously while charging.

To prevent damage to tool or property,
avoid contact with fences, trees, shrubs and the like.
DO NOT BUMP SPOOL HOUSING ON GROUND.
This string trimmer feeds Line
automatically when stopping.
Page 11
Automatic Line Feeder
NOTICE:
1 . After each operation, when Trigger is
released, Line will be fed out and cut
to proper length by Line Cutter.
2. If Trimmer is not cutting correctly, Spool may
be tangled. Remove Spool and rewind Line.
3. To advance Line by hand, push Line Outlet Button
on Spool Housing and pull out Line at the
same time. Approximately 1/4" of Line can be
pulled out each time the button is pushed.
Trimmer Operation
1 . Remove Battery Pack.
2. Adjust Auxiliary Handle as necessary.
3. Adjust length as necessary by turning
Extension Lock clockwise, pulling Extension
Tube out to desired length, then turning
Extension Lock Counterclockwise securely.
4. Adjust head angle by pushing Head Angle
Button, moving head until desired angle
is achieved, then releasing button.
5. Move Edge Guide down until it locks into place.
6. Install fully charged Battery Pack.
NOTICE:
7. Holding Trimmer with both hands, press
Trigger Safety Lock, then press Trigger.
8. DO NOT REST TRIMMER ON GROUND.
9. Do not force the Trimmer. Use the
tip of the Line to do the cutting.
10. Release Trigger when done.
11 . When finished, to prevent accidents:
• Remove battery pack..
• Wipe external surfaces of the appliance
with clean cloth. Store in an indoor
dry area out of reach of children.
Edger Operation
1 . Remove Battery Pack.
2. Push Edger/Trimmer Button, then rotate
head to the left until it clicks into place.
3. Adjust Auxiliary Handle as necessary..
4. Adjust length as necessary by turning
Extension Lock clockwise, pulling Extension
Tube out to desired length, then turning
Extension Lock Counterclockwise securely.
5. Adjust head angle by pushing Head Angle
Button, moving head until desired angle
is achieved, then releasing button..
6. Install fully charged Battery Pack.
NOTICE: To prevent damage to tool or property
avoid contact with fences, trees, shrubs and the like.
7. Rest Trimmer on Edger Wheels.
8. Holding Trimmer with both hands, press Trigger
Safety Lock, then press Trigger.
9. Do not force the Trimmer. Use the
tip of the Line to do the cutting.
10. Release Trigger when done.
11 . When finished, to prevent accidents:
• Remove battery pack.
• Wipe external surfaces of the appliance
with clean cloth. Store in an indoor
dry area out of reach of children.
WWW.LITHELI.COM
Item U1GT21000
To prevent damage to Trimmer,

Remove Battery Pack and wipe
external surfaces of the appliance with clean cloth.
inspect the general
condition of the appliance. Check for:
Replacement Spool is located
in Spool Storage Compartment.
Page 12
User-Maintenance and Storage
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION OR ELECTRIC SHOCK:
Release the Trigger and remove the Battery Pack before performing
any inspection, maintenance, or cleaning procedures.
TO PREVENT SERIOUS INJURY FROM APPLIANCE FAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.
Cleaning, Maintenance, and Lubrication
1 . BEFORE EACH USE,
• loose hardware,
• misalignment or binding of moving parts,
• cracked or broken parts,
• damaged electrical wiring,
• any other condition that may
affect its safe operation.
2. AFTER USE,
3. Li-Ion BATTERY MUST BE RECYCLED OR
DISPOSED OF PROPERLY.
Do not short, incinerate or open battery.
4. Store Battery Pack, Charger, and tool in dry, indoor
area out of reach of children and away from metal
objects (i.e., paperclips, coins) to prevent shorting.
5. All parts are permanently lubricated.
Do not use additional lubrication.
.
Replacing Spool
NOTE :
1 . Remove Battery Pack.
2. Press tabs on Spool Cover, remove Spool Cover,
then remove Spool from Spool Housing.
3. Remove old line from Spool.
4. Clean interior of Spool Housing with soft cloth.
5. Replace Spool, insert Line through Line Outlet in
Spool Housing and pull line out past Line Cutter.
6. Replace Spool Cover.
Tabs
Spool
Housing
Spool
Spool
Cover
Line
Outlet
Line
Cutter
WWW.LITHELI.COM Item U1GT21000

Page 13
Replacing Nylon Line
TO PREVENT SERIOUS INJURY:
Only replace the line on this appliance with the line material and diameter of line listed on
the Specifications table. Other materials, such as wire, rope, or blades can damage the
appliance and be forcefully and dangerously ejected from the appliance upon breaking.
1 . Remove Battery Pack.
2. Press tabs on Spool Cover, remove Spool Cover,
then remove Spool from Spool Housing.
3. Remove old line from Spool.
4. Clean interior of Spool Housing with soft cloth.
Tabs
Spool
Housing
Spool
Spool
Cover
Line
Outlet
Line
Cutter
5. Insert end of Nylon Line (up to 16 feet)
into Line Insertion Hole.
6. Wrap Line onto Spool in neat, straight rows, under
tension, following arrow direction on top of Spool.
Line
Insertion
Hole
Nylon
Line
7. Replace Spool, insert Line through Line Outlet in
Spool Housing and pull line out past Line Cutter.
8. Replace Spool Cover.
WWW.LITHELI.COM
Item U1GT21000

Page 14
Record Product’s Serial Number Here:
NOTE : If product has no serial number, record month and year of purchase instead..
NOTE : Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Part Description Qty
1 Battery Pack 1
2 Left Handle 1
3 Right Handle 1
4 Spool Storage Compartment 1
5 Replacement Spool 1
6 Battery Contact Plate 1
7 Battery Contact 3
8 PCB 1
9 Switch Pressing Plate 1
10 Pressing Plate Spring 1
11 Heat Shrink Tubing 1
12 Trigger Safety Lock Spring 1
13 Speed-Control Switch 1
14 PCB Box 1
15 Trigger Safety Lock 1
16 Internal Wire 1
17 Screw 9
18 Limit Block 1
19 Upper Tube 1
20 Auxiliary Handle 1
21 Auxiliary Handle Base 1
22 Auxiliary Handle Lock 1
23 Connection Shaft 1
24 Tube Cover 1
25 Inner Extension Tube Lock 1
26 Outer Extension Tube Lock 1
27 Extension Tube 1
28 Spring 1
29 Limit Block 1
30 Screw 10
31 Right Rotating Tube 1
32 Screw 3
33 Right Angle Adjusting Cover 1
34 Right Motor Housing 1
35 Cover 1
36 Left Rotating Tube 1
Part Description Qty
37 Inner Rotating Tube 1
38 Screw 2
39 Rotating Knob 1
40 Rotating Knob Spring 1
41 Cushion 2
42 Motor 1
43 Edge Guide 1
44 Motor Base 1
45 Line Outlet 1
46 Spool Housing 1
47 Spring Washer 2
48 Screw 2
49 Motor Connection Shaft 1
50 Line Outlet Button 1
51 Line Spool 1
52 Nylon Line - 16 ft 1
53 Spool Cover 1
54 Nut 1
55 Left Motor Housing 1
56 Edger Wheel Stand Plate 1
57 Screw 2
58 Angle Adjusting Button Spring 1
59 Angle Adjusting Button 1
60 Screw 2
61 Edger Wheel Stand 1
62 Flat Washer 2
63 Edger Wheel 2
64 Line Cutter 1
65 Guard 1
66 Screw 3
67 Line Outlet Button Spring 1
68 Balancing Weight 1 1
69 Balancing Weight 2 2
70 Dust Shield 1 1
71 Dust Shield 2 1
Parts List and Diagram
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Parts List
WWW.LITHELI.COM Item U1GT21000

Page 15
Assembly Diagram
WWW.LITHELI.COM
Item U1GT21000

Warranty
90-Day Money Back
You May Return Your Product for A Full Refund Within The First 90 Days of Your Purchase.
3-Year Battery and Charger Warranty
Against Defects in Workmanship and Materials.
Battery and Charger Must Be Used and Maintained in Accordance with The Manual of The
Operator's Instructions and Regulations.
5-Year Tool Warranty
Against Defects in Materials, Parts or Workmanship.
Litheli at Its Own Discretion Will Repair or Replace Any and All Parts Found To Be Defective.
All Units Must Be Used and Maintained in Accordance with The Directions and Regulations in The
Operator's Manual.
Returning The Product
Contact Us at www.litheli.com for The Return Address, We Will Issue Replace/Refund Upon Receiving
Your Return.
Need An Extra Copy of The Operator's Manual? Visit www.litheli.com to Download it.