Little Colorado Storage Cubby 64 User manual

WARNING: ADULT ASSEMBLY REQUIRED
WARNING: Assembly kit contains parts with sharp edges.
WARNING: Assembly kit contains parts with sharp points.
WARNING: Package contains plastic bags that present suffocation risks for children.
WARNING: Assembly kit contains small parts that present choking hazards for children.
Contents:
Top Qty 1
Bottom Qty 1
Left Side Qty 1 Right Side Qty 1
Pilot Hole for Bracket
Angle Brackets Qty 2
Horizontal Panel Qty 2
Back Panel Qty 3
Vertical Panel Qty 2
Quality Wooden Children’s Furniture and Accessories
Made in America • Established 1987
www.littlecolorado.com
Revised 06/17
by
D. Dominguez
Assembly Instructions for Storage Cubby Item #64
1 1/4" Screws Qty 30
5/8" Screws Qty 6
1/2" Screws Qty 4
Page 1 of 3

1. Identify all parts per the attached sketches. Some parts are very similar.
2. Build the outer frame consisting of the Right and Left sides, Top and Bottom. All slots face inside
and all panels fit securely in the slots. All screws go into pre-drilled holes only. The easiest method
to build the assembly is with the front (rounded) edges facing down on the floor. As the parts are
screwed together, pay careful attention that the 1/4" slots in the rear of each panel are aligned. Note
that there is no 1/4" slot in the rear of the Bottom panel. Use the 1 1/4" screws through the pre-drilled
holes in the Right and Left sides to secure the panels together.
3. Leave the unit face down on the floor. Now slide the two horizontal panels into the two sets of
slots in the Right and Left sides. The side of each Horizontal panel with the longer shallow slot must
face the Bottom panel. The side of the Horizontal panel that only has the slot that goes all the way
through faces the Top. Do not install the fasteners yet.
Page 2 of 3
*Note* Make sure Bottom is seated all the way forward in the slots. The rear of the Bottom will not line up with
the rear of the other sides. This gap is for inserting the Back Panels later.
Vertical Panel
4. Find the pilot hole 3/4" from the top on one side
of one end of the Vertical panels. Attach the Angle
Brackets with the 1/2" wood screws to both of these
Vertical panels. Position them so that these ends are
going to be up and slide them into the slots. They
may be a tight fit, care must be taken to that they are
fully seated into position and fully into the slots.
Rounded Edges Facing Floor
Pre-Drilled Holes
1/4" Slots
Bottom
Top
1 1/4" Screws
1/2" Screws
Angle Brackets
Revised 06/17

Page 3 of 3
5. While the unit is still face down, slide the three Back panels into the 1/4" slots from the bottom all
the way in until they are completely seated into the 1/4" slot in the underside of the Top panel. Make
sure the pre-drilled holes through one side of the Back panels are toward the Bottom. Install two 5/8"
screws through the pre-drilled holes in the bottom of each back. It is important that each panel be
completely in the slots to ensure a snug fit. These Back panels add a significant amount of stability to
the Storage Cubby and must be installed properly.
6. Check to be sure that all pieces are completely fitting into all slots. Install the remaining 1 1/4"
screws into the Left, Right, and Bottom panels. The two Vertical panels are attached to the underside
of the top using the two Angle Brackets with 1/2" screws.
A photo of this assembled product can be seen online at http://www.littlecolorado.com/stock64.html.
If you have questions about assembling this product, please call us and we will help you.
All of us at Little Colorado, LLC hope that you and your little ones enjoy this Storage Cubby for many years.
Please call us if you have any questions.
Manufactured in America by:
Little Colorado, LLC 4450 Lipan Street Denver, Colorado 80211
Phone [phone] Fax [phone] [email protected]
Inside Panels Assembly View
Back Panels Assembly View
Top
Top
Pre-Prilled holes for Angle
Brackets toward Top and facing
inside.
Long slots in Horizontal
panels face Bottom
5/8" Screws
Revised 06/17