Living Waters Majestic Falls User manual

Fountains of Living Waters, Inc.
Fountain Installation Instructions For All Wall Fountains
MajesticFalls–Yellowstone
DesertMirage Valentino
Just to name a few…. Fountains of Living Waters, Inc.
2320 Thompson Way, Unit B
Santa Maria, CA 93455
805-349-8442 – www.livingwatersfountains.com

FLW Wall Fountain Installation Instructions Page
2
These Instructions show you:
•How To Make Sure You Have Everything You Need To Install
Your New Fountain.
T
TO
OO OL LS S N
NE
EE ED DE ED D
•Phillips® Head Screw Driver (Power Screw Driver Optional)
•Level
•Pencil
A THE COMPONENTS
You will receive a fully assembled fountain, a Wall bracket, and the hardware to install it.
Fountain
Wall Bracket
EZ Anchors
Stainless screws

FLW Wall Fountain Installation Instructions Page
3
Maintenance and Operation Techniques
1. Distilled Water is recommended. Hard water contains
minerals, and after time, they will begin to leave unsightly
deposits on the face of your fountain. Should this happen,
turn off the pump. Cover water pan with plastic. Add a few
capfuls of CLR® to a gallon of water. With gloves and a soft
sponge, wipe off the face of the fountain. It may take several
minutes to remove the stains. Once they are gone, wipe
face of fountain with clear water. Refill basin, and plug pump
back in.
2. We recommend that these run 24/7. The water is pumped
by an aquarium type pump. They are manufactured to run
24/7. They pull very little electricity, about the same amount
needed to run a night light.
3. A soft cloth and some furniture polish for the copper
fountains, or stainless steel cleaner for the stainless steel
models is all that is needed to keep the fountain looking
beautiful. Just run the cloth over the exposed framing once
a week.
4. The water pan should be filled within 1 inch from the bottom
of the fountain face. This will adequately keep the pump
submerged. NEVER let your fountain run dry! It will burn
out your pump. That type of damage is not covered by the
Manufacturer’s warranty.
5. Should you have any problems with your Pump, You must
contact the pump manufacturer directly. Please refer to
Pump information insert that came with your fountain. The
pumps carry a three Year Limited Manufacturer’s Warranty.
Please read pump insert for more information. Fountains of
Living Waters cannot replace pumps.
6. Fountains of Living Waters recommend replacing the water
in your fountain every 3 months.

FLW Wall Fountain Installation Instructions Page
4
B Installing your wall fountain
1. Hold the wall bracket up to the desired height. The top of the light valance is
approximately 6-1/2” above the top of the wall bracket. Check to make sure the
bracket is level and mark holes.
2. Remove the wall bracket and insert the provided EZ Anchors™. You must use
the provided EZ Anchors™. Plastic anchors are not an acceptable
substitute. If you are mounting the fountain to a stud, do not use an EZ Anchor
TM.

FLW Wall Fountain Installation Instructions Page
5
3. Once you have installed the EZ Anchors, place the wall bracket over the
corresponding holes and using the Stainless screws provided, mount the bracket to
the wall. Before tightening the screws completely, check the level again of the wall
bracket. Once your satisfied with the level go ahead and tighten the screws.
4. Remover the dispersment cover and the splash guard from the fountain and set
aside.Your wall fountain has been equipped with a frame bracket, simply lift the
fountain above the wall bracket and lower it onto the wall bracket and center it.

FLW Wall Fountain Installation Instructions Page
6
5. Check to make sure that the fountain is seated on the bracket and that its
centered.
6. Fill the pan with Distilled water 1” from the bottom of the fountain face.

FLW Wall Fountain Installation Instructions Page
7
7. Plug your fountain in for just a few seconds and then unplug it. This will allow
the water to push any air out of the pump cavity. Plug your fountain in again
and allow the water to start cascading over the top of the dispersment
8. Use the scotch brite pad (provided) and rub the top dispersment from side to side
to insure that the water cascades evenly down the face of the fountain.

FLW Wall Fountain Installation Instructions Page
8
9. Once the water is cascading down the face of the fountain, install the
disbursement cover by setting it behind the Light Valance and lowering it onto the
disbursement. There are two tabs on the cover that will rest on the face of the
fountain.
10. Install your splash guard on the tabs located on the lower frame above the
pan, one side at a time. Then wipe up any water spots and…
Enjoy Your Fountain!!