Living 064-3178-8 Planning guide

ALTON ELECTRIC FIREPLACE
Model No.064-3178-8

Made in China

6
8
19
21
23
24
25
Operating Instructions
Care and Maintenance
Troubleshooting Guide
Replacement Parts List and Exploded View
risk
not be hung on it or near it.
trafc

Important Safety Instructions
off
Model No. 064-3178-8

Important Safety Instructions

6
Left front panel - 1
1
Right front panel - 1
2
Upper front panel - 1
3
Lower front panel - 1
4
Top strip - 1
5
Decorative block - 2
6
Left side panel - 1
9
Right side panel - 1
10
Upper Decorative Panel - 1
11
Right Decorative Panel - 1
12
Left Decorative Panel - 1
13
Top - 1
14
Bottom - 1
7
Firebox Down Support - 2
8
1
2
5
11
13
12
3
4
7
8
8
9
10
14
6
6
Parts List
Model No. 064-3178-8

7
Parts List
Screw 4 x 24 mm - 28
Wood dowel 7.8 x 20 mm - 10
Wood dowel 7.8 x 30 mm - 54
Cam - 22
Double-end cam bolt - 2
Screw 3.8 x 40 mm - 8
Screw 4 x 12 mm - 40
Metal plate - 6
A
B
C
D
E
F
G
H
J
Firebox L-bracket - 2
Fabric strip - 2
Screw 4 x 10 mm - 6
Metal washer - 4
K
L
M
N
Wall anchor - 2
O
Cam bolt - 18
Metal plate - 4
I

8
Assembly
160º~185º
Important Note:
+/- on the cam should be positioned
as shown.
Do not overtighten the cam bolt.
1. 2. 3.
4. 5.
HELPFUL HINTS
Read each section carefully before starting. It is very important that each step is performed in
the correct order. If these steps are not followed in sequence, assembly difculties will occur.
Make sure all parts are included. Most board parts are labelled or stamped on the raw edge.
Work in a spacious area, preferably on a carpet, near the place the unit will be located.
Do not use power tools to assemble your furniture. Power tools may strip or damage the parts.
Identify, sort and count the parts before beginning assembly.
Compression dowels should be tapped in with a rubber mallet.
Back panels provide stability and support. Unit may collapse without the back
panel installed.
Clean the product with your choice of furniture polish and a soft cloth. DO NOT USE harsh
chemicals or abrasive cleaners.
Move your new furniture carefully. Two people are needed to lift and carry the unit to its new
location.
Never push or drag your furniture (especially on a carpet).
This illustration shows how the cam-fastening system works.
Needed for assembly:
Rubber mallet Cross-head
screwdriver
Flat-head
screwdriver
2 people
wood dowels
Glue not enclosed. (We recommend to apply some
glue into holes before inserting wood dowels.)
Model No. 064-3178-8

Step 1
Requires 1, 2, 3, 4, A, C
Step 2
Requires 3, A, C, G, H
9
Assembly
A
A
A
C
C
G
H
C
ACGH
1
2
3
3
4

x 2
Requires 7, 8, A
Step 3
Step 4
Requires 7, 8, I
10 Model No. 064-3178-8
A
A
A
7
7
8
8
8
I
I

11
Step 5
Step 6
Requires 9, A, C, H, J
Requires 10, A, C, H, J
J
9
10
A
A
C
C
H
H
H
J
A
A
C
C
H
H
H
J
J
J
J
J

Step 7
Step 8
Requires 3, 4, 9, 10, D, H
Requires 7, 9, 10, D
12 Model No. 064-3178-8
4
3
7
9
9
10
10
D
D
D
D
H
H

Step 9
Step 10
Requires 12, 13, A
Requires 12, 13
13
12
13
A
A
13
12

x 2
Step 11
B
B
B
Requires 12, 13, F, I
Step 12
Requires 5, 6, B
14 Model No. 064-3178-8
5
6
F
I
I
I
12
F
13

Step 13
Requires 5, 6, F
15
5
6
6
F
Step 14
Requires 5, F Make sure the panels 6 and side panels are aligned. If necessary, adjust screws (F)
in step 13 for a good t.
Align and attach the top strip panel assembly in place by using screws (F). Make
sure the panel 5 and side panels are aligned before tightening the screws (F).
F
F
F
5
6
6
3
5
6

Step 15
Requires 11, D, E, F
Step 16
Requires 14, C
16 Model No. 064-3178-8
14
C
C
F
F
11
11
DE
E
D

Step 17
Requires 14, D
Step 18
17
14
D
D

Step 19
Requires F, K, L, M, N
WARNING
Young children may be injured by tipping furniture.The use of a tipping restraint is highly recommended. This
hardware, when properly installed, could provide protection against the unexpected tipping of furniture due
to improper use.
18 Model No. 064-3178-8
F
F
FF
K
K
K
L
L
L
L
M
M
M
M
N
N
N
N

Enjoy your furniture
WEIGHT LIMIT
Please make sure that all the items are
removed before moving the assembled unit.
The unit must be lifted by more than one person
not dragged or pushed. Failure to do so will
cause product damage, instability, product collapse,
and/or serious injury.
This unit has been designed to support the maximum
loads shown. Exceeding this load limit could
cause sagging, instability, product collapse,
and/or serious injury.
Step 20
Requires I, N, O
64 1/2 lb
(29.3 kg)
wall wall
19
Step 21
N
N
NN
O
O
OO
III
I

20 Model No. 064-3178-8
top right