Loctek D7d User manual

M4 x12mm
(8PCS) (8PCS)
M5 x12mm
A. B. C. E.
(3PCS)
M6 x12mm Φ6.5 xΦ13 x 2.0
(16PCS)
F.
4 x 4 Allen key
(1PC)
D.
(2PCS)
M6 x14mm
G.
5 x 5 Allen key
(1PC)
75 x 75 / 100 x 100 mm
75 x 75 / 100 x 100
25-120mm
Item No. D7D
Installation Guide
Package Included
Installation Steps
(A) Parts Included
(B) Attachment Screw Set
STEP 2 - Option A: Install bracket to the desk
(C)Tools Needed for Assembly
1. Verify that the monitor has holes at VESA spacings, either 100 x 100mm or 75 x 75mm.
If it does not have this pattern, the monitor cannot be installed.
2. Remove the monitor’s original fixed base. Be careful not to scratch the screen.
STEP 1: Preparations before installing monitor
This option is for desks without a gromment hole.
1. Attach the bottom support 2 (5) to the tube by tightening screws (C) with 4 x 4mm hex key (F).
2. Turn the mount upside-down and put anti-slip rubber 1 (8) and anti-slip rubber 2 (9) onto the
bottom support 2 (5).
3. Put anti-slip rubber 3 (10) onto the top of knob (6).
4. Attach the knob (6) to the bottom support 2 (5) using screws (D) with 4 x 4mm hex key (F).
5. Position the bottom clamp against desk surface and fully tighten clamp knob (6).
Tighten
Desk For table thickness: 0.98 – 4.72" "
(25 – 120mm) select appropriate
hole in the bottom support according
to the desk thickness.
100 x 100 4.4-19.8Ibs
2-9kg 10" - 27"
75 x 75 -90°-15°
F
F
①. Bottom support 1 x 1
②. Screw x 1
③. Washer x1
④. Butterfly knob 1 x 1
⑤. Bottom support 2 x 1
⑥. Knob x 1
⑦. Cable cover x 1
⑧. Anti-slip rubber 1 x 1
⑨. Anti-slip rubber 2 x 1
⑩. Anti-slip rubber 3 x 4
⑪. Washer x 1

Increase washer (E) based
on actual situation
A,B
E
G
Adjust the monitor’s height after installing.
If the monitor cannot stop at any height, pls
use the supplied 5x5 allen key to adjust the
screw on the arm. To make the mount and
monitor’s weight equal and it can stop at any
height, pls adjust the screw in “-” direction
when the monitor up and “+” direction when
it down.
±90°
±180°
A,B
-90°~15°
To adjust the
monitor with
the supplied
5x5 allen key(G)
EG
G
±90°
±180°
G
1. Add washers (E) to appropriate screws (A or B) – depending on monitor hole size.
2. Attach monitor to arm using the screws (A or B). For 100 x 100mm VESA holes,
first attach top screws to monitor and set monitor into top grooves of monitor plate (2).
3. Then add bottom screws through monitor plate and securely tighten all four screws.
Note: For 75 x 75mm VESA holes attach all four screws through monitor plate and tighten securely.
Step 2 - Option B: Install bracket using screw through hole in the desk
STEP 3: Attaching monitor to arm plate
This option is for desks with a grommet hole.
1. Insert the screw (2) into the hole of the bottom support 1 (1).
2. Attach the bottom support 1 (1) to the base by tightening screws (C) with 4 x 4mm hex key (F).
3. Turn the mount upside-down and put anti-slip rubber 1 (8) onto the bottom support 1 (1).
4. Insert the bottom support into the desk hole.
5. Attach anti-slip rubber 3 (10) onto the washer (3).
6. Screw in the washer with the butterfly knob (4).
Size of the hole: Φ 0.33" - 2.76" (8.5 - 70mm)
For table thickness: 0.78" - 4.72" (20 - 120mm)
Desk
Desk
Tighten
STEP 4: Using cable management system
32
Cable
5
14
2
1
2
1
Press
Slide cables through the underside of the arm, removing plastic cable guides if necessary.
(Press both sides to remove guides.)
Next, pass the cable along the slot in cable cover (7) and place cable cover around bottom
support 2 (5).
CAUTION
This product contains small items that could be a choking hazard if swallowed. Keep these items
away from young children.
● Make sure these instructions are read and completely understood before attempting installation.
If you are unsure of any part of this installation, please contact a professional installer for
assistance.
● The desk or mounting surface must be capable of supporting the combined weight of the mount
and the monitor, otherwise the structure must be reinforced.
● Proper tools must be used. A minimum of two people are required for this installation. Failure to
install properly can result in property damage.
● Check joint parts every two months, making sure the screws have not loosened.
This product was designed to be installed on a desk. Before installing, make sure the mount will
support the combined load of the equipment and hardware. Never exceed the maximum load
capacity 19.8 lbs (9 kg), or else it may result in product failure.
Note: This product is intended for indoor use only. Use of this product outdoors could lead to product
failure.
ADDRESS: 47618 Kato Road, Fremont, CA, 94538 United States
TEL: [phone]
Facebook: Loctek
Twitter: LoctekOfficial
Website: www.loctek.us
www pricedepot com
. .
ADDRESS: No. 588 Qihang South Road, Binhai Industrial Zone, Yinzhou District, Ningbo China
Website: www.loctek.com
(Distributor)
(Manufacturer)
F
Keep the screw side pointing down