Longshine PS960GLE User manual

PS960GLE/ PS965GME Mainboard
I
PS960GLE/ PS965GME
Intel®960GLE + ICH 8M
Intel®Celeron®processor FSB 533MHz
Intel®965GME + ICH 8M/ M-E(optional)
Intel®Core™ 2 Duo Mobile & Penryn processor FSB 533/800MHz
User's Manual
Ver. 1.0
MB Dimension
200mm x 195mm
Operating System
Windows®XP/ Linux
Release Date
090914

PS960GLE/ PS965GME Mainboard
II
Things You Have To Know
0The images and pictures in this manual are for reference only and may vary from the product
you received depending on specific hardware models, third party components and software
versions.
0This mainboard contains very delicate IC chips. Always use a grounded wrist strap when
working with the system.
0Do not touch any IC chip, lead, connector or other components.
0Always unplug the AC power when you install or remove any device on the mainboard or
when configuring pins and switches.
Symbols
A
ttention- Important
Follow the procedures
Refer to other
Troubleshootin
g
Tips

PS960GLE/ PS965GME Mainboard
III
Index
CHAPTER 1 GETTING STARTED ...............................................................................1
1.1 INTRODUCTION ....................................................................................................1
1.2 SPECIFICATION ....................................................................................................2
1.2.1 CPU .................................................................................................................................. 2
1.2.2 Chipset.............................................................................................................................. 2
1.2.3 Memory ............................................................................................................................. 2
1.2.4 Audio - Realtek®ALC 662................................................................................................. 2
1.2.5 LAN - Realtek®RTL8111C................................................................................................ 3
1.2.6 Slot.................................................................................................................................... 3
1.2.7 Mini-IDE Connector........................................................................................................... 3
1.2.8 I/O Connectors.................................................................................................................. 3
1.2.9 Universal Serial Bus.......................................................................................................... 3
1.2.10 SATA II............................................................................................................................ 3
1.2.11 BIOS ............................................................................................................................... 4
1.2.12 Hardware Monitor............................................................................................................ 4
1.2.13 Power Supply.................................................................................................................. 4
1.3 CONFIGURATION..................................................................................................5
1.3.1 Layout of TOP................................................................................................................... 5
1.4 HARDWARE INSTALLATION ..................................................................................6
Jumpers ..................................................................................................................................... 6
1.4.1 JP1: Clear CMOS Jumper................................................................................................. 6
1.4.2 JP2: CF Card Master/ Slave Jumper................................................................................. 7
1.4.3 JP3: LVDS VDD POWER ................................................................................................. 7
1.4.4 JP4: USB POWER ............................................................................................................7
1.4.5 JP5/ JP6: FAN Power .......................................................................................................7
1.4.6 JP7: RJ12 POWER...........................................................................................................8
1.4.7 JP8: MINI PCI ON/OFF..................................................................................................... 8
1.4.8 JP9: EXT. Audio................................................................................................................ 8
1.4.9 CN1 - 6: RS-232 Voltage Setting ...................................................................................... 8
1.4.10 CN12: AUDIO OUTPUT SELECT................................................................................... 9
1.4.11 CN13: KB/MS.................................................................................................................. 9
1.4.12 CN9: LVDS Selection.................................................................................................... 10
1.4.13 CN8 FPSWLED: Front Panel Headers.......................................................................... 11

PS960GLE/ PS965GME Mainboard
IV
Connectors............................................................................................................................... 12
1.4.14 KBMS1: Mini-DIN PS/2 Port.......................................................................................... 12
1.4.15 CON3/ CON4: COM3/ 4/ 5/ 6 Port ................................................................................ 12
1.4.16 PRT1: LPT PORT ......................................................................................................... 13
1.4.17 RJ12.............................................................................................................................. 13
1.4.18 VGA1: VGA Connector ................................................................................................. 14
1.4.19 LAN1: LAN Port............................................................................................................. 14
1.4.20 USB1: USB Port............................................................................................................ 15
1.4.21 SNDCN2 ....................................................................................................................... 15
1.4.22 COM1/ COM2: COM Port ............................................................................................. 15
1.4.23 CN14: 8-bit GPIO.......................................................................................................... 16
1.4.24 CDIN1 ........................................................................................................................... 16
1.4.25 SPDIF ........................................................................................................................... 16
1.4.26 USB2/ USB3: USB Connector ...................................................................................... 17
1.4.27 SATA1/ SATA2/ SATA3................................................................................................ 17
1.4.28 IDE1: Mini-IDE Connector............................................................................................. 17
1.4.29 CON2: LVDS................................................................................................................. 18
1.4.30 DDRII1/ DDRII2: Memory Installation............................................................................ 19
1.4.31 PWR1: ATX Power Connector ...................................................................................... 20
1.4.32 FAN1/ FAN2/ FAN3: FAN Header................................................................................. 20
1.4.33 MINI_PCI1: Mini PCI Slot.............................................................................................. 21
1.4.34 CON1: CF Card Connector ........................................................................................... 21
2.3 MAIN MENU .......................................................................................................22
2.3.1 Standard CMOS Features............................................................................................... 23
2.3.2 Advanced BIOS Features ............................................................................................... 26
2.3.3 Advanced Chipset Features............................................................................................ 31
2.3.4 Integrated Peripherals..................................................................................................... 34
2.3.5 Power Management Setup.............................................................................................. 40
2.3.6 PnP/PCI Configurations .................................................................................................. 44
2.3.7 PC Health Status............................................................................................................. 45
2.3.8 Frequency/Voltage Control ............................................................................................. 46
2.3.9 Load Fail-Safe Defaults...................................................................................................47
2.3.10 Load Optimized Defaults............................................................................................... 48
2.3.11 Set Password................................................................................................................ 49
2.3.12 Save & Exit Setup ......................................................................................................... 50
2.3.13 Exit Without Saving ....................................................................................................... 51

PS960GLE/ PS965GME Mainboard
1
Chapter 1 Getting Started
1.1 Introduction
Thanks for choosing PS960GLE/ PS965GME Mainboard. It is based on Intel®960GLE/ 965GME
Northbridge chipset and Intel®ICH 8M/ M-E(optional) Southbridge chipset. In addition, it also supports
integrated Intel®960GLE/ 965GME Graphics Engine for onboard graphics feature. It supports Intel®
Celeron®processor by 960GLE; supports Intel®Core™ 2 Duo Mobile & Penryn processor by
965GME.
The PS960GLE/ PS965GME provide 2 DDR II SO-DIMM sockets which allow you to install 200-pin
DDR II 533(PS960GLE) or 667(PS965GME)MHz SO-DIMM. It supports a total memory capacity of
2(PS960GLE) or 4(PS965GME) GB.
This mainboard provides one MINI-IDE connector for MINI-IDE hard drives, supporting Ultra ATA
100/66/33MHz. and support 3 SATA II (300MB/s). In addition, Mini PCI & CF II slot for use with
standard expansion card is also allowed.
The PS960GLE/ PS965GME provide one VGA (D-Sub) connector, 8 USB 2.0/ 1.1 and 6 RS232 ports
for use. There are maximal 8 USB2.0/ 1.1 ports which can be set up on this mainboard.
This mainboard also comes with one onboard 10/100/1000 Mbps Ethernet LAN chips (RTL8111C). On
the back panel of your case that you can directly plug into Internet cables.
The onboard Realtek®ALC 662 AC’97 Codec supports high quality performance.

PS960GLE/ PS965GME Mainboard
2
1.2 Specification
1.2.1 CPU
Support Intel®Celeron®processor w/ FSB 533MHz (PS960GLE)
Support Intel®Core™ 2 Duo Mobile & Penryn processor w/ FSB 533/800MHz
(PS965GME)
1.2.2 Chipset
Northbridge Chipset - Intel®960GLE/ 965GME
Southbridge Chipset -
PS960GLE: Intel®ICH 8M or
PS965GME: Intel®ICH 8M/ M-E (optional)
Super I/O Controller - W83627UHG
IO RS-232 Controller - W83627UHG
AC’97 Audio Codec - Realtek®ALC 662
LAN Controller - PCI-E Realtek®RTL8111C
1.2.3 Memory
2 DDR II SO-DIMM socket
Support 200-pin DDR II 533(PS960GLE) or 667(PS965GME)MHz SO-DIMM
Support a total memory capacity of up to 2(PS960GLE) or 4(PS965GME) GB
1.2.4 Audio - Realtek®ALC 662
Compliant with AC’97 2.3 specification
Support SPDIF output (cable by optional)
Support 3D stereo enhancement

PS960GLE/ PS965GME Mainboard
3
1.2.5 LAN - Realtek®RTL8111C
PCI-E Realtek®Giga LAN Ethernet LAN
RJ45 Connector with link/act and speed LED integrated
1.2.6 Slot
One standard 32-bit Mini PCI slot for Mini PCI standard expansion card
Supporting one-way bandwidth up to 33 MB/s
1.2.7 Mini-IDE Connector
One Mini-IDE Connector for two Mini-IDE 44pin hard disk drives
CF card type I/II
Ultra ATA 33/66/100 MHz
High capacity hard disk drives
1.2.8 I/O Connectors
One Mini-DIN PS/2 connector
4 x COM port (COM3 ~COM6) & 2 x COM by pin header (COM1 & COM2)
1.2.9 Universal Serial Bus
8 x USB 2.0/ 1.1 (4 x USB by pin header)
1.2.10 SATA II
3 x SATA II (300MB/s)

PS960GLE/ PS965GME Mainboard
4
1.2.11 BIOS
Phoenix-Award™ BIOS
1.2.12 Hardware Monitor
Monitor CPU temperature and FAN speed
Monitor system voltages
1.2.13 Power Supply
ATX 24 pin power

PS960GLE/ PS965GME Mainboard
5
1.3 Configuration
1.3.1 Layout of TOP

PS960GLE/ PS965GME Mainboard
6
1.4 Hardware Installation
This section will assist you in quickly installing your system hardware. Wear a wrist ground strap
before handling components. Electrostatic discharge may damage the system's components.
Jumpers
1.4.1 JP1: Clear CMOS Jumper
The "Clear CMOS" function is used when you are unable boot your system and need to reset the
BIOS settings (CMOS settings) back to the manufacturer's original settings. This is also a way to
reset the system password if you have forgotten it.
JP1 Assignment
Pin 1-2 Closed
Normal (Default)
Pin 2-3 Closed
Clear CMOS Data
Note: "Closed" means putting a jumper cap onto two adjacent header pins.
1. Turn off your system and disconnect the AC power cable.
2. Set JP1 header to OFF (2-3 Closed).
3. Wait several seconds.
4. Set JP1 header to ON (1-2 closed).
5. Connect the AC power cable and turn on your system.
6. Reset your new password.
The following steps explain how to reset your CMOS
configurations when you forgot a system password.

PS960GLE/ PS965GME Mainboard
7
1.4.2 JP2: CF Card Master/ Slave Jumper
This Jumper is to select the CF works on Secondary Channel master device or Slave device.
JP2 Assignment
Pin 1-2 Closed
Slave (Default)
Pin 2-3 Closed
Master
1.4.3 JP3: LVDS VDD POWER
It’s for LVDS VDD power setting.
JP3 Assignment
Pin 1-2 Closed
5V
Pin 2-3 Closed
3V (Default)
1.4.4 JP4: USB POWER
+5V or +5V STB for USB
JP4 Assignment
Pin 1-2 Closed
5V (Default)
Pin 2-3 Closed
5V STB
1.4.5 JP5/ JP6: FAN Power
This is a 3-pin header for the fan. JP5 is for Fan2, JP6 is for Fan3.
JP5/ JP6 Assignment
Pin 1-2 Closed
12V (Default)
Pin 2-3 Closed
5V

PS960GLE/ PS965GME Mainboard
8
1.4.6 JP7: RJ12 POWER
It’s for RJ12 power setting.
JP7 Assignment
Pin 1-2 Closed
24V (Default)
Pin 2-3 Closed
12V
1.4.7 JP8: MINI PCI ON/OFF
It’s for MINI PCI ON/OFF setting.
JP8 Assignment
Pin 1-2 Closed
OFF
Pin 1-2 Open
On (Default)
1.4.8 JP9: EXT. Audio
It’s for EXT. Audio setting.
JP9 Pin Assignment
1 CON_R
2 CON_L
3 +5V
4 GND
1.4.9 CN1 - 6: RS-232 Voltage Setting
It’s for RS-232 Voltage setting. The correspondence between CN# & COM# is below:
CN1ÆCOM1, CN2ÆCOM2, CN3ÆCOM4, CN4ÆCOM3, CN5ÆCOM6, CN6ÆCOM5.
Assignment
Pin 1-2 Closed
+5V
Pin 3-4 Closed
RINGW(Default)
Pin 5-6 Closed
+12V

PS960GLE/ PS965GME Mainboard
9
1.4.10 CN12: AUDIO OUTPUT SELECT
It’s for audio output select setting.
CN12 Assignment
Pin 1-3 & 2-4 Closed
Audio Connector
Pin 3-5 & 4-6 Closed
JP9
The default setting is “Pin 1-3 & 2-4 Closed“.
1.4.11 CN13: KB/MS
The following table shows the pin outs of the INT_KBMS connectors.
Pin Assignment Pin Assignment
1 KBDATA_C 2 KBDATA
3 KBCLK_C 4 KBCLK
5 +5V 6 GND
7 MSDATA_C 8 MSDATA
9 MSCLK_C 10 MSCLK
The default setting is “Pin 1-2, 3-4, 7-8, 9-10 Closed“.

PS960GLE/ PS965GME Mainboard
10
1.4.12 CN9: LVDS Selection
The LCD panel, inverter for LCD LAMP, Touch-screen Serial Interface must be connected to this
LVDS header, using the below described connector:
ID 0 1024x768x24(Dual) ID 1 1280x1024x24(Dual)
ID 2(default) 1024x768x24(Single)
ID 3 1600x1200x18(Single)
ID 4 640x480x18(Single)
ID 5 640x480x24(Single)
ID 6 800x600x18(Single)
ID 7 1024x768x18(Single)
ID 8 1024x768x18(Dual)
ID 9 1280x768x18(Single)
ID 10 1280x768x24(Single) ID 11 1280x800x18(Dual)
ID 12 1366x768x18(Single)
ID 13 1400x1050x18(Dual)
ID 14 1440x900x18(Single) ID 15 D-Sub only

PS960GLE/ PS965GME Mainboard
11
1.4.13 CN8 FPSWLED: Front Panel Headers
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection.
It allows user to connect the PC case’s front panel switch functions.
Pin Assignment Pin Assignment
1 N/C 2 N/C
3 EXTRST- 4 GND
5 PWRLED+ 6 PWRLED-
7 HDD LED+ 8 HDD LED-
9 PWRBTI 10 PWRBTI-
11 ACT LED+ 12 ACT LED-
13 SPEED LED+ 14 SPEED LED-

PS960GLE/ PS965GME Mainboard
12
Connectors
1.4.14 KBMS1: Mini-DIN PS/2 Port
This mainboard provides a standard Mini-DIN PS/2 port to connect PS/2 keyboard and mouse.
Pin Assignment Pin Assignment
1 Keyboard/
Mouse data
2 N/C
3 GND 4 5V
5 Keyboard/
Mouse clock
6 GND
1.4.15 CON3/ CON4: COM3/ 4/ 5/ 6 Port
A 9-pin D-Sub male connector is the serial port. The following table shows its pin assignments.
Pin Assignment Pin Assignment
1 DCD 2 SIN
3 SOUT 4 DTR
5 GND 6 DSR
7 RTS 8 CTS
9 +5V/RINGW/
+12V

PS960GLE/ PS965GME Mainboard
13
1.4.16 PRT1: LPT PORT
The following table shows its pin assignments.
Pin Assignment Pin Assignment
1 RSTB- 14 RAFD-
2 RPDR0 15 P_ERR-
3 RPDR1 16 RINIT_P-
4 RPDR2 17 RSLIN-
5 RPDR3 18 GND
6 RPDR4 19 GND
7 RPDR5 20 GND
8 RPDR6 21 GND
9 RPDR7 22 GND
10 P_ACK- 23 GND
11 P_BUSY 24 GND
12 P_PE 25 GND
13 P_SLCT
1.4.17 RJ12
The following table shows its pin assignments.
Pin Assignment Pin Assignment
1 GND 2 GND
3 Sensor_IN 4 24V/12V
5 N/C 6 Sensor_IN

PS960GLE/ PS965GME Mainboard
14
1.4.18 VGA1: VGA Connector
The mainboard provides one VGA connector (= D-Sub connector) on back panel.
VGA connector (= D-Sub connector) delivers the analogy signals, and is able to connect with
traditional CRT display, flat display, or other display device which with the D-Sub interface
compatible.
Pin Assignment
1 RED
2 GREEN
3 BLUE
4 N/A
5 GND
6 GND
7 GND
8 GND
9 NVGA03
10 GND
11 N/A
12 DDC_DATA
13 5VHSYNC
14 5VVSYNC
15 DDC_CLK
1.4.19 LAN1: LAN Port
There is one PCI-E Realtek®Giga Ethernet LAN port available for you to attach Internet cables

PS960GLE/ PS965GME Mainboard
15
1.4.20 USB1: USB Port
There are 4 USB 2.0/ 1.1 ports. These USB ports are used to attach with USB devices, such as
keyboard, mouse and other USB supported devices.
1.4.21 SNDCN2
1.4.22 COM1/ COM2: COM Port
This mainboard provides four COM pin headers for you to connect additional serial connectors on
your case back panel. Attach cables of serial connectors onto these headers, then you can use
the serial connectors connecting with a mic, modem or other peripheral device.
Pin Assignment Pin Assignment
1 DCD 2 SIN
3 SOUT 4 DTR
5 GND 6 DSR
7 RTS 8 CTS
9 +5V/RINGW/
+12V
10 N/C

PS960GLE/ PS965GME Mainboard
16
1.4.23 CN14: 8-bit GPIO
8-bit General Purpose Input/Output
Pin Assignment Pin Assignment
1 DIO_0 2 DIO_1
3 DIO_2 4 DIO_3
5 DIO_4 6 DIO_5
7 DIO_6 8 DIO_7
9 GND 10 +5V
1.4.24 CDIN1
Pin Assignment
1 CDL
2 CDG
3 CDG
4 CDR
1.4.25 SPDIF
S/PDIF specifies a Data Link Layer protocol and choice of Physical Layer specifications for
carrying digital audio signals between devices and stereo components over either optical or
electrical cable.
Pin Assignment
1 5V
2 N/A
3 SPDIFO
4 GND
5 N/C