Lowell LPTR4-1023 User manual

Lowell strives to provide accurate information while reserving the right to change specications and/or improve manufacturing methods without prior notication.
©2018 Lowell Manufacturing Co., 100 Integram Dr., Pacic MO 63069 / tel. [phone] / www.lowellmfg.com
Spec #1580 | Rev. 11-09-2018
pg. 1/2
features. . . . . . . . . . . . .
a&e specifications . . . . . . . . . .
• Panel Space: 10U or 17.50" [445]
• Overall Height: 20.08" [510]
• Overall Depth: 23.38" [594]
• Pulled-out Depth: 45.36" [1152]
• Overall Width: 19.13" [486]
• Bottom Slide Rails: 4
• Description: For built-in applications, rack slides forward
on support rails in base, then rotates left or right, locking at
60 or 90 degrees, providing superior access to equipment
connections. Ships unassembled (two cartons).
• Construction: 14-ga. certified U.S. steel base and 11-ga.
corner post rails with smooth black powder epoxy finish.
• Mounting Rails: Includes four (10U) 11-ga. steel corner
post mounting rails tapped 10-32 with bi-directional num-
bered RU increments to mount in either direction, plus two
rear rails (10U) for wire tie-off.
• Cable Management: Six rear cable lacing bars. Obrounds
in side panels and base. Lower section of base has a large
central opening.
The EIA/TIA compliant 19" equipment rack shall be Lowell #LPTR4-
1023 with overall dimensions of 20.08"H x 23.38"D x 19.13"W
and usable height of 10 rack units. Rack construction shall be cer-
tified U.S. steel—14-gauge base with 11-gauge corner post rails
tapped 10-32—with smooth black powder epoxy finish. The rack
shall slide forward on four (4) rails in the base, and shall rotate
and lock at 60 and 90 degrees. Base and side panels shall feature
multiple obrounds for ventilation or cable management. The rear
• Hardware: Pilot point screws with captive washers for
quick assembly
• Compliance: EIA/TIA compliant. RoHS compliant.
• Load Capacity: Four (4) bottom slide rails support total
load capacity of 200 lbs.
• Installation: The base can be mounted flush or recessed
up to 1.75" to allow room for equipment knobs. Leave
sufficient room at sides for rack rotation. Base secures
to turntable with front/rear screws. Front security panel
screws into position to deter unauthorized access to
mounted equipment.
• Operation: Remove front security panel, grasp rails and
pull rack firmly towards you, sliding it along rails in base
(locks when fully forward). To rotate, press center button to
release turntable and rotate left or right (locks at 60 and 90
degrees). To return, rotate back to 0 degrees and depress
right tab to release lock and slide back into base.
• Optional:
– Steel top cover, black (#LPTR-TC)
– Zero-space shelf, black (#LPTR-NS)
shall include six cable lacing bars. The rack shall support a load
capacity of 200 lbs. It shall be manufactured in the U.S.A. and ship
unassembled.
Optional
• The rack shall include zero-space shelf #LPTR-NS.
• The rack shall include steel top #LPTR-TC.
Pull & Turn Rack #LPTR4-1023
for built-in applications (cabinetry or millwork)
10U x 23"D x 19"W
LPTR series summary
Post Mtg Rear Tie Bottom Slide Overall Pulled-out Usable Overall Usable Overall Side Load
Model No. Rails (4) Rails (2) Rails Depth Depth Depth Height Height Width Brackets Capacity
LPTR2-1019 10 U 10 U 2 19.22 [488] 38.30 [973] 19.00 [483] 20.08 [510] 17.50 [445] 19.13 [486] --- 125 lbs.
LPTR2-1219 12 U 12 U 2 19.22 [488] 38.30 [973] 19.00 [483] 23.58 [599] 21.00 [533] 19.13 [486] --- 125 lbs.
LPTR2-1419 14 U 12 U 2 19.22 [488] 38.30 [973] 19.00 [483] 27.08 [688] 24.50 [622] 19.13 [486] --- 125 lbs.
LPTR2-1619 16 U 14 U 2 19.22 [488] 38.30 [973] 19.00 [483] 30.58 [777] 28.00 [711] 19.13 [486] --- 125 lbs.
LPTR2-2119 21 U 18 U 2 19.22 [488] 38.30 [973] 19.00 [483] 39.33 [999] 36.75 [933] 19.13 [486] --- 125 lbs.
LPTR2-2419 24 U 23 U 2 19.22 [488] 38.30 [973] 19.00 [483] 44.58 [1132] 42.00 [1067] 19.13 [486] --- 125 lbs.
LPTR4-1019 10 U 10 U 4 19.22 [488] 38.30 [973] 19.00 [483] 20.08 [510] 17.50 [445] 19.13 [486] --- 250 lbs.
LPTR4-1219 12 U 12 U 4 19.22 [488] 38.30 [973] 19.00 [483] 23.58 [599] 21.00 [533] 19.13 [486] --- 250 lbs.
LPTR4-1419 14 U 12 U 4 19.22 [488] 38.30 [973] 19.00 [483] 27.08 [688] 24.50 [622] 19.13 [486] --- 250 lbs.
LPTR4-1619 16 U 14 U 4 19.22 [488] 38.30 [973] 19.00 [483] 30.58 [777] 28.00 [711] 19.13 [486] --- 250 lbs.
LPTR4-2119 21 U 18 U 4 19.22 [488] 38.30 [973] 19.00 [483] 39.33 [999] 36.75 [933] 19.13 [486] --- 250 lbs.
LPTR4-2419 24 U 23 U 4 19.22 [488] 38.30 [973] 19.00 [483] 44.58 [1132] 42.00 [1067] 19.13 [486] --- 250 lbs.
LPTR4-2819 28 U 24 U 4 19.22 [488] 38.30 [973] 19.00 [483] 51.58 [1310] 49.00 [1245] 19.13 [486] Y 250 lbs.
LPTR4-3019 30 U 28 U 4 19.22 [488] 38.30 [973] 19.00 [483] 55.08 [1399] 52.50 [1334] 19.13 [486] Y 250 lbs.
LPTR4-1023 10 U 10 U 4 23.38 [594] 45.36 [1152] 23.00 [584] 20.08 [510] 17.50 [445] 19.13 [486] --- 200 lbs.
LPTR4-1223 12 U 12 U 4 23.38 [594] 45.36 [1152] 23.00 [584] 23.58 [599] 21.00 [533] 19.13 [486] --- 200 lbs.
LPTR4-1423 14 U 12 U 4 23.38 [594] 45.36 [1152] 23.00 [584] 27.08 [688] 24.50 [622] 19.13 [486] --- 200 lbs.
LPTR4-1623 16 U 14 U 4 23.38 [594] 45.36 [1152] 23.00 [584] 30.58 [777] 28.00 [711] 19.13 [486] --- 200 lbs.
LPTR4-2123 21 U 18 U 4 23.38 [594] 45.36 [1152] 23.00 [584] 39.33 [999] 36.75 [933] 19.13 [486] --- 200 lbs.
LPTR4-2423 24 U 23 U 4 23.38 [594] 45.36 [1152] 23.00 [584] 44.58 [1132] 42.00 [1067] 19.13 [486] --- 200 lbs.
LPTR4-2823 28 U 24 U 4 23.38 [594] 45.36 [1152] 23.00 [584] 51.58 [1310] 49.00 [1245] 19.13 [486] Y 200 lbs.
LPTR4-3023 30 U 28 U 4 23.38 [594] 45.36 [1152] 23.00 [584] 55.08 [1399] 52.50 [1334] 19.13 [486] Y 200 lbs.
Rack dimensions (rounded) – inches and [mm]; 1U = 1.75"
100% CERTIFIED
US STEEL
MADE IN
THE U.S.A
COMPLIANT
COMPLIANT

Lowell strives to provide accurate information while reserving the right to change specications and/or improve manufacturing methods without prior notication.
©2018 Lowell Manufacturing Co., 100 Integram Dr., Pacic MO 63069 / tel. [phone] / www.lowellmfg.com
Spec #1580 | Rev. 11-09-2018
pg. 2/2
Dimensions are inches and [mm] unless stated otherwise.
Pull & Turn Rack #LPTR4-1023
FRONT VIEW
18.312
C
Lto C L
17.81
[452]
rear cable
lacing bars
front
security panel
BASIC OPERATION: Rack pictured may depict a different size than spec sheet.
SECURING:
After wiring, attach front
security panel with screws.
Note: Use screws to secure
rack even if security panel is
not utilized.
DOCKING:
Rack can be removed from base for
offsite integration.
OPERATING:
Slide Out: Grasp two front rails and pull rack firmly towards you, sliding
it along rails in base. Rack locks in place when fully forward (0 degrees).
Rotate: Press center button to release turntable and rotate rack left or
right. Rack locks in place at 60 and 90 degrees.
Slide In: With rack rotated back to 0 degrees, depress right tab to
release lock and slide rack back into base.
WIRING:
Ensure adequate slack is allowed
for rotation by performing wire
tie-offs with rack in fully rotated
position (90 degrees).
center
button right
tab
BASE (PULLED OUT)
18.17
[461]
45.36
[1152]
4 bottom slide rails
BASE (UPPER SECTION)
19.13 [486]
BASE (LOWER SECTION)
19.13 [486]
8.00 [203]
18.00 [457]
8.00 [203]
6.00
[152]
18.81 [478]
18.81 [478]
23.23
[590]
0.28 [7]
13.87
[352]
13.87
[352]
1.89 [48]
5.26 [134]
0.37 [9]
8.62 [219]
0.19
[5]
6.56
[167]
SIDE VIEW
17.50
[445]
10U
20.08
[510]
17.50
[445]
10U
23.38 [594]
16.75
[425]