Lowrance GlobalMap 5300C iGPS User manual

Pub. 988-0152-191
www.lowrance.com
GlobalMap®5300c iGPS
Mapping GPS Receiver
Operation Instructions
www.Busse-Yachtshop.de email: [email protected]

Copyright © 2006 Lowrance Electronics, Inc.
All rights reserved.
No part of this manual may be copied, reproduced, republished, trans-
mitted or distributed for any purpose, without prior written consent of
Lowrance. Any unauthorized commercial distribution of this
manual is strictly prohibited.
Lowrance®is a registered trademark of Lowrance Electronics, Inc.
MapCreate™, FreedomMaps™and NauticPath™are trademarks of
LEI. Fishing Hot Spots®is a registered trademark of Fishing Hot Spots
Inc. LakeMaster®and Pro Maps are trademarks or registered trade-
marks of WayPoint Technologies, Inc. Navionics®is a registered trade-
mark of Navionics, Inc. DURACELL®is a registered trademark of
Duracell, Inc. RAYOVAC®is a registered trademark of Rayovac Corpo-
ration. Energizer®and e2®are registered trademarks of Energizer Hold-
ings, Inc.
Points of Interest Data in this unit are by infoUSA,
copyright ©2001-2006, All Rights Reserved. infoUSA is a
trademark of infoUSA, Inc.
Lowrance Electronics may find it necessary to change or end our poli-
cies, regulations and special offers at any time. We reserve the right to
do so without notice. All features and specifications subject to change
without notice. On the cover: GlobalMap 5300c iGPS. All screens in
this manual are simulated.
For free owner's manuals and the most current information on
this product, its operation and accessories,
visit our web site:
www.lowrance.com
Lowrance Electronics Inc.
12000 E. Skelly Dr.
Tulsa, OK USA 74128-2486
Printed in USA.
www.Busse-Yachtshop.de email: [email protected]

i
Table of Contents
Section 1: Read Me First! ......................................................... 1
Specifications: GlobalMap®5300c iGPS ...................................... 2
How to use this manual: typographical conventions .................. 8
Section 2: Installation............................................................. 11
Preparations ................................................................................ 11
Power Connections ...................................................................... 11
Powering Your Display Unit ...................................................... 12
Power Diagram A ........................................................................ 14
Power Diagram B ........................................................................ 15
Powering a NMEA 2000 Network Bus ...................................... 15
Connecting to a NMEA 2000 Network ...................................... 16
NMEA 0183 Cable Connections ................................................. 16
NMEA 0183 Wiring................................................................. 16
Mounting the Unit: Bracket or Portable ................................... 18
MMC or SD Card Memory Card Installation............................ 22
Other Accessories ........................................................................ 23
Cleaning Towel ........................................................................ 23
Face Cover ................................................................................... 24
Section 3: Basic GPS Operation ........................................... 25
Keyboard ...................................................................................... 25
Power/lights on and off ............................................................... 26
Main Menu................................................................................... 26
Pages ............................................................................................ 28
Satellite Status Page............................................................... 28
Navigation Page ...................................................................... 30
Map Page ................................................................................. 33
Background map vs. MapCreate map content ...................... 34
Map with Custom Gauges....................................................... 37
Radar............................................................................................ 38
Basic GPS Quick Reference ........................................................ 40
Find Your Current Position........................................................ 41
Moving Around the Map: Zoom & Cursor Arrow Keys............. 41
Selecting Any Map Item With the Cursor ................................. 42
Searching ..................................................................................... 42
Set a Waypoint ............................................................................ 44
Navigate To a Waypoint ............................................................. 46
Set Man Overboard (MOB) Waypoint........................................ 47
Navigate Back to MOB Waypoint .............................................. 47
Navigate to Cursor Position on Map.......................................... 48
Navigate to a Point of Interest ................................................... 49
Creating and Saving a Trail ....................................................... 50
www.Busse-Yachtshop.de email: [email protected]

ii
Displaying a Saved Trail ............................................................ 51
Navigating Trails ........................................................................ 52
Transfer Custom Maps and GPS Data Files ............................. 56
Cancel Navigation ....................................................................... 58
Section 4: Advanced Operations .......................................... 59
Find Distance from different Locations..................................... 59
Find Distance from Point to Point ............................................. 59
Icons ............................................................................................. 59
Create Icon on Map ................................................................. 60
Create Icon at Current Position ............................................. 60
Delete an Icon .......................................................................... 60
Navigate to an Icon ................................................................. 61
Routes .......................................................................................... 61
Create and Save a Route ........................................................ 62
Delete a Route ......................................................................... 64
Edit a Route Name .................................................................. 64
Edit Route Waypoints ............................................................. 65
Navigate a Route ..................................................................... 66
Navigate a Route in Reverse .................................................. 66
Trails ............................................................................................ 67
Delete a Trail ........................................................................... 67
Edit a Trail Name ................................................................... 68
Edit a Trail Color .................................................................... 68
Edit a Trail Pattern................................................................. 68
Utilities ........................................................................................ 69
Alarm Clock ............................................................................. 69
Sun/Moon Rise & Set Calculator............................................ 69
Trip Calculator ........................................................................ 69
Trip Down Timer ..................................................................... 69
Trip Up Timer.......................................................................... 69
Waypoints .................................................................................... 69
Delete a Waypoint ................................................................... 69
Edit a Waypoint....................................................................... 70
Selecting a Waypoint .............................................................. 70
Set a Waypoint by Average Position...................................... 71
Set a Waypoint by Projecting a Position................................ 72
Section 5: System & GPS Setup............................................ 73
Alarms.......................................................................................... 73
Auto Satellite Search .................................................................. 74
Check MMC Files and Storage Space........................................ 75
Communications Port Configuration ......................................... 75
Configure NMEA......................................................................... 76
Coordinate System Selection...................................................... 76
www.Busse-Yachtshop.de email: [email protected]

iii
Map Fix ........................................................................................ 78
Customize Page Displays............................................................ 79
GPS Simulator............................................................................. 80
Initialize GPS .............................................................................. 82
Map Auto Zoom ........................................................................... 83
Map Data ..................................................................................... 83
Map Datum Selection.................................................................. 85
Map Detail Category Selection................................................... 86
Map Orientation.......................................................................... 86
NauticPath™USA Marine Charts............................................. 87
Nautical Chart Notes .............................................................. 88
Port Information...................................................................... 88
Tidal Current Information...................................................... 89
Tide Information ..................................................................... 91
Navionics®Charts ....................................................................... 92
Overlay Data ............................................................................... 93
Pop-up Help ................................................................................. 97
Reset Options............................................................................... 98
Screen Contrast and Brightness ................................................ 99
Set Language ............................................................................. 100
Set Local Time ........................................................................... 100
Show WAAS Alarm ................................................................... 101
Software Version Information .................................................. 102
Sounds and Alarm Sound Styles .............................................. 102
Track Smoothing ....................................................................... 104
Trail Options.............................................................................. 104
Transparency............................................................................. 107
Units of Measure ....................................................................... 108
Section 6: Searching.............................................................. 111
Find Streets ............................................................................... 111
Find Any Item Selected by Map Cursor .................................. 113
Find Interstate Highway Exits ................................................ 113
Find Map Places or Points of Interest (POI) ........................... 116
Find Streets or Intersections.................................................... 118
Find Waypoints ......................................................................... 121
Section 7: NMEA 2000 ........................................................... 125
NMEA 2000 Menu..................................................................... 125
Internal GPS Receiver .............................................................. 125
Bus Setup................................................................................... 126
Engine & Tank Configuration.................................................. 127
Tank Select ........................................................................ 127
Tank Size ........................................................................... 128
Set Configuration button .................................................. 128
www.Busse-Yachtshop.de email: [email protected]

iv
Device Configuration Menu.................................................. 129
Device Information and Device Data ................................... 129
Fuel Management Menu........................................................... 130
Tank Location .................................................................... 130
Fuel Added ......................................................................... 130
Add Fuel............................................................................. 130
Fill Tank............................................................................. 131
Adding Fuel to Tank ............................................................. 131
Engine Operations................................................................. 131
Engine Select ..................................................................... 131
NMEA 2000 Alarms .................................................................. 132
Waypoint Sharing ..................................................................... 133
Backlight Synchronization ....................................................... 133
Configuring EP Sensors............................................................ 133
EP-35 Temperature Configuration ...................................... 134
Advanced Options menu ....................................................... 134
Instance.............................................................................. 134
Restore Defaults ................................................................ 135
EP-10 Fuel Flow Configuration............................................ 135
Advanced Options menu ....................................................... 136
Instance.............................................................................. 136
Restore Defaults ................................................................ 136
EP-15 Fluid Level Configuration ......................................... 137
Advanced Options menu ....................................................... 138
Instance.............................................................................. 138
Restore Defaults ................................................................ 139
Suzuki Engine Interface Configuration............................... 139
Advanced Options menu ....................................................... 140
Instance.............................................................................. 140
Restore Defaults ................................................................ 141
Calibrating EP Sensors............................................................. 141
EP-10 Fuel Flow Calibration................................................ 141
EP-15 Fluid Level Calibration ............................................. 143
2-Point Calibration............................................................ 143
3-Point Calibration............................................................ 144
5-Point Calibration............................................................ 145
Fuel Flow Calibration in a Suzuki Engine Interface.......... 146
Engine Trim Calibration....................................................... 147
Reset Trim Calibration ......................................................... 148
Bennett Trim Tabs Calibration ............................................ 148
Section 8: Supplemental Material ..................................... 151
www.Busse-Yachtshop.de email: [email protected]

v
NOTICE!
The storage and operation temperature range for your unit is from -20
degrees to +167 degrees Fahrenheit (-28 degrees to +75 degrees Cel-
sius). Extended storage or operation in temperatures higher or lower
than specified will damage the liquid crystal display in your unit. This
type of damage is not covered by the warranty. For more information,
contact the factory's Customer Service Department; phone numbers are
listed on the last page of the manual.
WARNING!
A CAREFUL NAVIGATOR NEVER RELIES ON ONLY ONE METHOD
TO OBTAIN POSITION INFORMATION.
CAUTION
When showing navigation data to a position (waypoint), a GPS unit will show
the shortest, most direct path to the waypoint. It provides navigation data to the
waypoint regardless of obstructions. Therefore, the prudent navigator will not
only take advantage of all available navigation tools when traveling to a way-
point, but will also visually check to make sure a clear, safe path to the waypoint
is always available.
WARNING!
When a GPS unit is used in a vehicle, the vehicle operator is solely re-
sponsible for operating the vehicle in a safe manner. Vehicle operators
must maintain full surveillance of all pertinent driving, boating or flying
conditions at all times. An accident or collision resulting in damage to
property, personal injury or death could occur if the operator of a GPS-
equipped vehicle fails to pay full attention to travel conditions and vehi-
cle operation while the vehicle is in motion.
www.Busse-Yachtshop.de email: [email protected]

vi
Notes
www.Busse-Yachtshop.de email: [email protected]

1
Section 1: Read Me First!
How this manual can get you out on the road, fast!
Welcome to the exciting world of digital GPS! We know you're anxious
to begin navigating, but we have a favor to ask. Before you grab the
GlobalMap®5300c iGPS and begin installing it, please give us a mo-
ment or two to explain how our manual can help you get the best per-
formance from your compact, wide-screen, mapping GPS receiver.
First, we want to thank you for buying a Lowrance GPS unit. Whether
you're a first time user or a professional fisherman, you'll discover that
your GlobalMap 5300c is easy to use, yet capable of handling demand-
ing navigation tasks. When you team your unit with our custom map-
ping software MapCreate™, you have an incredible combination. You
won't find another GPS unit with this much power and this many fea-
tures for this price!
Our goal for this book is to get you on the road fast, with a minimum of
fuss. Like you, we'd rather spend more time navigating and less time
reading the manual!
So, we designed our book so that you don't have to read the whole thing
from front to back for the information you want. At the start (or end) of
each segment, we'll tell you what content is coming up next. If it's a
concept you're already familiar with, we'll show you how and where to
skip ahead for the next important topic. We've also made it easy to look
up any tips you may need from time to time. Here's how:
The manual is organized into 7 sections. This first section is an intro-
duction to Lowrance GPS. It tells you the basics you need to know be-
fore you can make the unit look around and tell you where you are.
Section 2 will help you install your unit. We'll show you how to get the
MultiMedia Card (MMC) correctly installed inside the unit. We'll also
tell you about some of the available accessories.
Section 3 covers Basic GPS Operation. It will show you how easy it is to
run the GlobalMap 5300c, right out of the box. This section features a
one-page GPS Quick Reference. (If you've already jumped ahead
and figured out how to install the unit yourself, and you just
can't wait any longer, turn to the Quick Reference on page 40
and head for the road with your GPS unit!)
Section 3 contains short, easy-to-scan GPS lessons that follow one an-
other in chronological order. They're all you'll need to know to find your
way on the water or in the wilderness quickly.
www.Busse-Yachtshop.de email: [email protected]

2
After you've learned the basics (or if you already have some GPS ex-
perience), you may want to try out some of the GlobalMap 5300c's
many advanced navigation features. That brings us to Section 4, Ad-
vanced GPS Operations.
When you come to a GPS menu command on the GlobalMap 5300c's
screen, you can look it up in the manual by skimming over the table of con-
tents, just flipping through Section 3 or scanning through the command
portion of Section 4.
This unit is ready to use right out of the box, but you can fine tune and
customize its operation with dozens of options. We describe how to use
general system options along with GPS options in Section 5, System Setup
and GPS Setup Options.
In Section 6, we go into more detail on one of the GlobalMap 5300c's
most remarkable capabilities — Searching. We'll introduce a search
example in the Basic GPS Operation section, but there are so many
map items you can search for, we had to give this function its own sec-
tion in the manual! For example, did you know this unit can look up
business phone numbers, functioning as a virtual Yellow Pages? We’ll
show you how in Section 6.
Finally, in Section 7, we offer Supplemental Material, including a list of
the GPS datums used, warranties and customer service information.
Now, if you're into the fine details, glance over the next segment on speci-
fications to see just how much GPS power your GlobalMap 5300c con-
tains.
Specifications: GlobalMap®5300c iGPS
General
Display: ............................Color 5.0" (12.7 cm) diagonal; SolarMax™
TFT display programmable to viewing pref-
erence.
Resolution: ......................480 pixel x 480 pixel resolution; 230,400 to-
tal pixels.
Backlighting: ................... Fluorescent cold cathode backlit screen with
multiple lighting levels; backlit keypad.
Input power: ...................10 to 15 volts DC.
Case size: .........................5.4" H x 6.9" W x 3.4" D (13.8 x 17.6 x 8.6
cm); sealed and waterproof; suitable for salt-
water use.
MMC slots:.......................One with waterproof door (SD card compati-
ble).
www.Busse-Yachtshop.de email: [email protected]

3
Recording: ........................ MMC & SD memory cards for recording GPS
trip details and displaying charts or maps.
Back-up memory:...........Built-in memory stores GPS data for dec-
ades. User settings are stored when unit is
turned off.
Languages: ......................10; menu languages selectable by user.
GPS
Receiver/antenna: .........Internal; Built-in 12 parallel channel
GPS/WAAS .
Background map: ..........Built-in custom, detailed Lowrance map.
Contains: enhanced detail of continental U.S.
and Hawaii. Includes more than 60,000 nav
aids and 10,000 wrecks/obstructions in
coastal and Great Lakes waters. Metro ar-
eas, selected major streets/highways and in-
terstate exit services details included.
Custom mapping:...........MapCreate™software optional; optional
plug and play LEI FreedomMaps™offer the
same high detail without the computer work
of MapCreate. Other plug and play mapping
options include Fishing Hot Spots® Elite, LEI
NauticPath™, LakeMaster®ProMaps and
Navionics®charts.
Mapping memory: .........Up to 2 gigabytes on one MMC (or SD) card.
Position updates:...........Every second.
Position points: ..............1,000 waypoints; 1,000 event marker icons.
Audible alarms:..............Arrival/off-course/anchor.
Graphic symbols for
waypoints or event
marker icons:..................63.
Routes: .............................100; up to 100 waypoints per route.
Plot Trails:.......................10 savable; up to 9,999 points per trail.
Zoom range: ....................39 ranges; 0.02 to 4,000 miles.
NOTE:
The above memory capacities refer only to the GlobalMap 5300c's on-
board memory. The amount of GPS data you can record and save for
recall later is limited only by the number of MMC cards you have.
www.Busse-Yachtshop.de email: [email protected]

4
How Lowrance GPS Works
You'll navigate faster and easier if you understand how the GlobalMap
5300c scans the sky to tell you where you are on the earth — and,
where you're going. (But if you already have a working understanding
of GPS receivers and the GPS navigation system, skip on ahead to Sec-
tion 2, Installation & Accessories on page 11. If you're new to GPS, read
on, and you can later impress your friends with your new-found knowl-
edge.)
First, think of your unit as a small but powerful computer. (But don't
worry — we made it easy to use, so you don't need to be a computer ex-
pert to find your way!) The GlobalMap 5300c includes a keypad and a
screen with menus so you can tell it what to do. The screen also lets the
unit show your location on a moving map, as well as point the way to
your destination.
This gimbal-mounted GlobalMap 5300c uses an internal an-
tenna/receiver module, which makes the whole system work something
like your car radio. But instead of your favorite dance tunes, this re-
ceiver tunes in to a couple of dozen GPS satellites circling the earth. (It
will also listen in to the WAAS satellites in orbit, but more about that
in the upcoming segment introducing you to GPS and WAAS.)
Your unit listens to signals from as many satellites as it can see above
the horizon, eliminates the weakest signals, then computes its location
in relation to those satellites. Once the GlobalMap 5300c figures its
latitude and longitude, it plots that position on the moving map shown
on the screen. The whole process takes place several times a second!
The performance doesn't stop there. Stored in the permanent memory
of each unit is a basic background map of the entire world. We lock it in
here at the factory — you can't change or erase this map.
The background map is suitable for many navigation chores, but for
maximum accuracy and much more detail, you need our optional map-
making software, MapCreate™. Some unit features — such as search-
ing for businesses and addresses — won't work without a custom Map-
Create map. There is so much detail in our background map (and even
more in MapCreate) that we'll describe their contents and differences
in Section 3, Basic GPS Operations, on page 34.
Another portion of the GlobalMap 5300c's onboard memory is devoted to
recording GPS navigation information, which includes waypoints, event
marker icons, trails and routes. This lets you look back the way you came.
Think of this data storage like the hard drive memory in a computer or a
tape in a cassette tape recorder. You can save several different GPS data
www.Busse-Yachtshop.de email: [email protected]

5
files, erase 'em and record new ones, over and over again. Like any com-
puter file, these GPS Data Files (file format *.usr) can be shared be-
tween Lowrance GPS or sonar/GPS units or even personal computers.
This GlobalMap 5300c has one more thing in common with a personal
computer. Just as computers have a floppy disk drive for storing and ex-
changing files, the unit has a slot for an MMC (MultiMedia Card) or SD
(Secure Digital card) flash memory card. These solid-state memory de-
vices are about the size of a postage stamp, but can hold data ranging
from 8 MB to 2 GB in size. (Compare that to a floppy disk's 1.44 MB ca-
pacity!) This unit uses all that MMC space for two key GPS purposes.
First, you can backup your onboard GPS Data Files by copying them to
the MMC. Since the MMC is removable (like a floppy disk or a cassette
tape), you can store these GPS Data Files on a personal computer
equipped with an MMC card reader. (Or store them on a pocketful of
MMCs, if you don't have a computer.) Our MapCreate mapping software
can save, edit or create its own GPS Data Files, which can be copied to the
MMC and then loaded from the MMC into the unit's memory. (NOTE: No
matter where they come from, GPS Data Files must be loaded from the
MMC into memory before the GlobalMap 5300c can use them.)
The other key GPS use for MMCs is storage of special high-detail, cus-
tom maps, which you can produce on your computer with our MapCre-
ate software. These MapCreate custom maps contain much greater de-
tail than the basic background map. These Custom Map Files (file
format *.lcm) can also be shared between Lowrance GPS or sonar/GPS
units and personal computers.
This unit automatically reads Custom Map Files directly from the
MMC or SD card. To use a custom map, all you need to do is slide an
MMC containing a map into the GlobalMap 5300c.
Introduction to GPS and WAAS
Well, now you know the basics of how the unit does its work. You might
be ready to jump ahead to Section 2, Installation & Accessories, on page
11, so you can mount your GlobalMap 5300c and plug in the power. Or
you might want to see how our text formatting makes the manual tuto-
rials easy to skim. If that's the case, move on to "How to Use This Man-
ual" on page 8. But, if you want to understand the current state of sat-
ellite navigation, look over this segment describing how GPS and its
new companion WAAS work together to get you where you're going.
The Global Positioning System (GPS) was launched July 17, 1995 by the
United States Department of Defense. It was designed as a 24-hour-a-
day, 365-days-a-year, all weather global navigation system for the armed
www.Busse-Yachtshop.de email: [email protected]

6
forces of the U.S. and its allies. Civilian use was also available at first,
but it was less accurate because the military scrambled the signal some-
what, using a process called Selective Availability (SA).
GPS proved so useful for civilian navigation that the federal govern-
ment discontinued SA on May 2, 2000, after the military developed
other methods to deny GPS service to enemy forces. Reliable accuracy
for civilian users jumped from 100 meters (330 feet) under SA to the
present level of 10 to 20 meters (about 30 to 60 feet.)
Twenty-four satellites orbit 10,900 nautical miles above the Earth, pass-
ing overhead twice daily. A series of ground stations (with precisely sur-
veyed locations) controls the satellites and monitors their exact locations
in the sky. Each satellite broadcasts a low-power signal that identifies
the satellite and its position above the earth. Three of these satellites are
spares, unused until needed. The rest virtually guarantee that at least
four satellites are in view nearly anywhere on Earth at all times.
A minimum of three satellites are required to determine a 2D fix.
The system requires signal reception from three satellites in order to
determine a position. This is called a 2D fix. It takes four satellites to
determine both position and elevation (your height above sea level —
also called altitude). This is called a 3D fix.
Remember, the unit must have a clear view of the satellites in order to
receive their signals. Unlike radio or television signals, GPS works at
very high frequencies. These signals can be easily blocked by trees,
buildings, an automobile roof, even your body.
Like most GPS receivers, this unit doesn’t have a compass or any other
navigation aid built inside. It relies solely on the signals from the satel-
lites to calculate a position. Speed, direction of travel, and distance are
all calculated from position information. Therefore, in order for the
GlobalMap 5300c to determine direction of travel, you must be moving
and the faster, the better.
www.Busse-Yachtshop.de email: [email protected]

7
This is not to say that it won’t work at walking or trolling speeds — it
will. There will simply be more "wandering" of the data shown on the
display.
GPS alone is accurate for route navigation, but the U.S. Federal Avia-
tion Administration has special aircraft navigation needs that go be-
yond basic GPS. So, the FAA has developed a program to boost GPS
performance with its Wide Area Augmentation System, or WAAS. The
FAA commissioned the system on July 11, 2003.
WAAS is designed to increase GPS accuracy to within 7.6 meters verti-
cally and horizontally, but it consistently delivers accuracies within 1-2
meters horizontal and 2-3 meters vertical, according to the FAA. It does
this by broadcasting correction signals on GPS frequencies. Your unit
automatically receives both GPS and WAAS signals.
There, however, are some fringe areas of the U.S., including parts of
Alaska that do not yet receive robust WAAS coverage. Continued
WAAS development is planned to extend WAAS coverage in the years
to come.
WAAS boosts the accuracy of land GPS navigation, but the system is
designed for aircraft. The satellites are in a fixed orbit around the
Equator, so they appear very low in the sky to someone on the ground
in North America. Aircraft and vessels on open water can get consis-
tently good WAAS reception, but terrain, foliage or even large man-
made structures can sometimes block the WAAS signal from ground
receivers.
You'll find that using your GPS receiver is both easy and amazingly
accurate. It’s easily the most accurate method of electronic navigation
available to the general public today. Remember that this receiver is
only a tool. Always have another method of navigation available, such
as a map or chart and a compass.
Also remember that this unit will always show navigation information
in the shortest line from your present position to a waypoint, regardless
of terrain! It only calculates position, it can’t know what’s between you
and your destination, for example. It’s up to you to safely navigate
around obstacles, no matter how you’re using this product.
Free Training Aids Available
Now that you know something about the technology that makes this
unit possible, you are ready to start learning how to use that technol-
ogy. This manual will guide you through the process of setting up and
running your unit, but that is only one of many resources available.
www.Busse-Yachtshop.de email: [email protected]

8
If you or a friend has Internet access, visit our web site. Find us at
WWW.LOWRANCE.COM. The site is packed with additional information
on using our products.
Emulator
For the ultimate training aid, be sure to download the free emulator
software for your unit. This program can help you learn both basic and
advanced operations without burning fuel!
This PC application simulates the actual GPS unit on your computer.
You can run it from your computer keyboard or use your mouse to press
the virtual keys. Easy download and installation instructions are avail-
able on our web site.
The emulator works exactly like your real GPS unit. When using the
GPS Simulators you can run GPS routes and trails, even create real
waypoints you can use in the field.
And that is just some of the material available on our web site. To find
out what we have available, log on and look around. For now, we'll get
back to how to use this particular unit.
How to use this manual: typographical conventions
Many instructions are listed as numbered steps. The keypad and arrow
"keystrokes" appear as boldface type. So, if you're in a real hurry (or
just need a reminder), you can skim the instructions and pick out what
menu command to use by finding the boldface command text. The fol-
lowing paragraphs explain how to interpret the text formatting for
those commands and other instructions:
Arrow Keys
The arrow keys control the movement of dotted cross-hair lines on your
mapping screen called the cursor. The arrow keys help you move
around the menus so you can execute different commands. They are
represented by symbols like these, which denote the down arrow key,
the up arrow, the left arrow and the right arrow: ↓↑,←→.
Keyboard
The other keys perform a variety of functions. When the text refers to a
key to press, the key is shown in bold, sans serif type. For example, the
"Enter/Icons" key is shown as ENT and the "Menu" key is shown as
MENU.
Menu Commands
A menu command or a menu option will appear in small capital letters,
in a bold sans serif type like this: ROUTE PLANNING. These indicate that
you are to select this command or option from a menu or take an action
www.Busse-Yachtshop.de email: [email protected]

9
of some kind with the menu item. Text that you may need to enter or
file names you need to select are show in italic type, such as trail name.
Instructions = Menu Sequences
Most functions you perform with this unit are described as a sequence
of key strokes and selecting menu commands. We've written them in a
condensed manner for quick and easy reading.
For example, instructions for navigating a trail would look like this:
1. From the Map Page, press MENU|MENU|↓to MY TRAILS|ENT.
2. Press ↓to Trail 1|ENT|→|↓to NAVIGATE|ENT.
3. You are asked to wait while it converts the trail into a route.
4. The wait message disappears and the GlobalMap 5300c begins
showing navigation information along the trail. Now, begin moving
and follow your GlobalMap 5300c.
Translated into complete English, step 1 above would mean: "Start on
the Map Page. Press the Menu key twice. Next, repeatedly press (or
press and hold) the down arrow key to scroll down the menu and select
(highlight) the My Trails menu command. Finally, press the Enter key."
Step 2 would mean: "Press the down arrow key repeatedly to scroll to
the trail named Trail 1, and press Enter. Next, press the right arrow
key and then the down arrow key to highlight the Navigate command,
then press Enter."
www.Busse-Yachtshop.de email: [email protected]

10
Notes
www.Busse-Yachtshop.de email: [email protected]

11
Section 2: Installation
Preparations
You can install the GPS system in some other order if you prefer, but
we recommend this installation sequence:
Caution:
You should read over this entire installation section before drill-
ing any holes in your vehicle or vessel!
1. Determine the approximate location for the GPS unit, so you can
plan how and where to route the power cable. This will help you make
sure you have enough cable length for the desired configuration.
NOTE:
The GPS antenna is inside the unit, so you must mount the unit in
a location with an unobstructed view of the sky.
2. Determine the location of your battery or other power connection,
along with the power cable route.
3. Install the power cable and route it to the GPS unit.
4. Mount the GPS unit.
Power Connections
Your unit comes with a power/data cable that splits into three
branches, each with several exposed wires.
The thicker three-wire cable (white, red and black) is the power supply
for your display unit. This cable has no label.
The thinner branch with three wires (red, black and shield) is the
power cable for a NMEA 2000 network. It is labeled "NMEA 2000
POWER."
The branch with four wires (blue, yellow, orange, and shield) is a data
cable, labeled "RS-232 COMM." It supports a serial communication
port. This allows your unit to exchange NMEA 0183 data with another
device, such as an autopilot, DSC marine radio or computer.
www.Busse-Yachtshop.de email: [email protected]

12
The Power/Data cable for this unit.
NOTE:
There are two basic power connection options, which are shown in
the following two diagrams. Read the following instructions
carefully to determine which power connection applies to
your unit. Depending on your configuration, you may not use all of
these wires.
Caution:
All of the wires in the power/data cable have bare ends for eas-
ier installation. The bare ends on any unused wires could cause
an electrical short if left exposed. To prevent this, you should
cover the individual wire ends – either by capping them with
wire nuts, wrapping them with electrical tape or both. (You
should cut off the bare wire before taping off the ends.)
Powering Your Display Unit
The display unit works from a 12-volt DC battery system. Attach the
display power cable (with provided 3-amp fuse) to an accessory switch
or power bus. If this results in electrical interference, connect direct to
a battery but install an in-line switch on the cable.
Caution:
We strongly recommend that you shut off the power supply to the
power cable when the unit is not in use, especially in saltwater en-
vironments. When the unit is turned off but still connected to a
power supply, electrolysis can occur in the power cable plug. This
may result in corrosion of the plug body along with the electrical
contacts in the cable and the unit's power socket. Risk of electroly-
sis corrosion is even greater when the cable is unplugged from the
unit, but still connected to a power source.
We recommend you connect the power cable to the auxiliary power
switch included in most boat designs. If that results in electrical
To unit
Display unit power wires:
white, red and black
NMEA 2000 power wires:
red, black and shield
Data cable wires:
blue, yellow, orange,
and shield
www.Busse-Yachtshop.de email: [email protected]