LTV LTV-ICDMxE4230 User manual

LTV-ICDMxE4230
LTV Europe Sicherheitstechnik GmbH
Am Wall 113
28195 Bremen
Germany
www.ltv-cctv.eu
[e-mail]
3. Rear Panel Connection
1 Package
After you receive your device, please check the following accessories.
The pictures here are for reference only.
IP-CAM
Quick Start
CD
Terminal Block
Mounting
Screwdriver
Screws
Guide
for Power
Block
For the mounting block, please attach it flat side to the
front. Screwdriver: To adjust the back focus ring.
2.Side Panel Instruction
4
1
DC
1
Damp -
2
Damp +
3
2
3
Driver +
4
Driver -
Focus Adjusting Iris Lens Plug
Focus Adjusting: When it still fails to realize focusing after having
confirmed the correct lens interface, the back focus adjustment may be
required. Operate the following steps: tighten the lens firstly and then
loose the fixed back focus ring; rotate the lens slowly until the video
image turns to be clear, and finally tighten and lock the back focus ring.
Iris Lens Plug: The camera provides an iris lens plug in negative pattern with
four square holes and the definition of pins is shown above. The interface of DC
drive auto iris adopts four pins: Damp+, Drive+, Damp- and Drive-.
1
③Connect the power supply and video output.
④Attach the mounting block to the bracket and then install the bracket to the
wall and tighten the screws to fix it as shown below. Please make sure that
the wall is strong enough to withstand three times the weight of the camera.
Mounting Block
4.Installation
①Rotate the lens clockwise onto the lens mount of the camera.
②Plug the wire of auto iris lens to the auto iris interface of the camera.
2
⑤Attach the camera to the bracket with the mounting block and tighten
the screws to fix.
5 IE Network Connections
●LAN
In LAN, there are two ways to access. 1. Access through IP-
Tool; 2. Directly Access through IE Browser
►Access the camera through IP-Tool
①Make sure that the camera and the PC are well connected to the LAN.
②Find the IP-Tool from the CD and then install it in the
computer. After that, run the IP-Tool as shown below.
23
1
Reset key
7
SD card slot
2
Audio input port
8
Alarm output port
3
Audio output port
9
Alarm input port
4
Reserved antenna port
10
Connect to PTZ
5
Video output port
11
Network port
6
Power indicator
12
Connect to Power

③Modify the IP address. The default IP address of this camera is
192.168.226.201. Click the information of the camera listed in the above
table to show the network information on the right hand. Modify the IP
address and gateway of the camera and make sure its network address is
in the same local network segment as the computer’s. Please modify the
IP address of your device according to the practical situation.
For example, the IP address of your computer is 192.168.13.4. So the
IP address of the camera shall be changed to 192.168.13.X.
After modification, please input the password of the administrator and
click “Modify” button to modify the setting.
The default password of the administrator is “123456".
④Double-click the IP address and then the system will pop up the IE
browser to connect IP-CAM . IE browser will auto download the Active X
control. After downloading, a login window will pop up as shown below:
Input the user name and password to login.
The default user name is admin; the default password is 123456.
►Directly Access Through IE
The default network settings are as shown below:
IP address: 192.168.226.201 HTTP:80
Subnet Mask: 255.255.255.0 Data Port:9008
Gateway: 192.168.226.1
5
You may use the above default settings when you log in the camera
for the first time.
①Manually set the IP address of the PC and the network segment
should be as the same as the default settings of IP-CAM. Open the
network and share center. Click “Local Area Connection” to pop up the
following window. Select “Property” and then select Internet protocol
according to the actual situation (for example: IPV4). Next, click
“Property” button to set the network of the PC.
6
①Make sure the camera is well connected via LAN. Then log in the
camera via LAN and go to the System Congfig→Network Config→Port
menu to set up the port number.
②Enter System Config→Network Config→Wired menu to modify
the IP address.
③Go to the router’s management interface through IE browser to
forward the IP address and port of IP-CAM in the “Virtual Server”.
④Open the IE browser and input its WAN IP and HTTP port to
access the IP-CAM.
Port Config IP Config
②Open the IE Browser and input the default address of IP-CAM and
confirm. The IE browser will download Active X control automatically.
③After downloading Active X control, the login dialog box will pop up.
④Input the default username and password and then enter to view.
●WAN
Router Config
Take access through the router or virtual server for example.
7
8
450043000135 A0