manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Luma Surveillance
  6. •
  7. Rack & Stand
  8. •
  9. Luma Surveillance LUM-MNT-JNT-BUL-GR User manual

Luma Surveillance LUM-MNT-JNT-BUL-GR User manual

Bullet Junction Mount
Surveillance Accessory
Installation
Manual
1: Installation
Before you start, ensure that the hardware is in good condition and all assembly
parts are included.
Check that the mounting surface is strong enough to withstand three times the
weight of the mount and camera.
If installing on a cement surface, use the included expansion anchors to install
the mount. If installing on a wood surface, use self-tapping wood screws (not
included) to secure the mount.
Take care that all equipment is powered off during installation.
If the product does not assemble properly, please contact technical support.
Compatibility
This can be used with all Luma Surveillance bullet cameras, except for the 100
series mini bullet.
It can be mounted on Luma Surveillance pole mounts.
2: Box Contents
Before installing, familiarize yourself with the parts of your mount.
}Face plate
}Housing
}Self-adhesive drill template
}4 wall anchors
}4 screws
Other Required Equipment
}Bullet camera
}Phillips screwdriver
3: Prepare for Installation
Remove the face plate from the housing and set it aside.
The mount comes with one conduit plug and one conduit connector.
If you will be running a conduit through the side of the housing, no changes
are needed.
If you will be running a conduit through the mounting surface, replace the
conduit connector with the conduit plug. Tighten the conduit plug with a
quarter or a large flathead screwdriver.
If you will be running a conduit through a pole mount, you may wish to
swap the locations of the conduit plug and the conduit connector. Tighten
the conduit plug with a quarter or a large flathead screwdriver. Secure the
conduit connector by tightening the thin hex nut by hand.
Mounting holes
for 300-, 500- and
700-series bullets The locking nut
tightens the seal
around the cabling.
The thin nut secures
the connector to the
junction mount.
Version 160505-0833
5: Install the Camera
Thread the wires from your camera through the face plate, then attach your
camera to the face plate using the screws supplied with the camera.
Hang the looped wire attached to the face plate over the hook on the interior of
the junction mount. This holds the camera in place, leaving your hands free.
Connect the camera wiring to your surveillance network.
Once everything is connected, screw the bullet / face plate assembly onto the
housing.
You can now power up your camera and finish installation using the
instructions in its manual.
6: Weatherproofing
While the gasket provided helps block moisture, we recommend you run a
silicone bead between the base of the bullet and the face plate, as well as
between the junction mount and the mounting surface. If the wiring runs out
of the side of the housing, also seal the conduit connector.
Support
If you need help, email support@SnapAV.com. For information, instructional
videos, support documentation, or ideas, visit our website.
5-Year Limited Warranty
This Luma Surveillance™ product has a 5-Year Limited Warranty. This warranty
includes parts and labor repairs on all components found to be defective in material
or workmanship under normal conditions of use. This warranty shall not apply to
products that have been abused, modified or disassembled. Products to be repaired
under this warranty must be returned to a designated service center with an assigned
return authorization (RA) number. Contact technical support for an RA number.
Copyright ©2015 Luma Surveillance. All rights reserved.
4: Install the Housing
Using the self-adhesive template provided, drill pilot holes as needed, as well
as a cable hole through the mounting surface if desired.
Remove the self-adhesive template.
Secure the housing to the mounting surface.
Thread the wires from your surveillance
system through the housing.

Popular Rack & Stand manuals by other brands

NeoMounts PLASMA-M1950E instruction manual

NeoMounts

NeoMounts PLASMA-M1950E instruction manual

Stell SHO 1070 Universal Mounting Instructions

Stell

Stell SHO 1070 Universal Mounting Instructions

Vivo STAND-V000D5 instruction manual

Vivo

Vivo STAND-V000D5 instruction manual

Victaulic VAPS224 Operating and maintenance instruction manual

Victaulic

Victaulic VAPS224 Operating and maintenance instruction manual

LG T6 installation guide

LG

LG T6 installation guide

BACK40 SOLAR VC1-HR4 manual

BACK40 SOLAR

BACK40 SOLAR VC1-HR4 manual

ERARD LUX-UP 1400L manual

ERARD

ERARD LUX-UP 1400L manual

Manfrotto Mega Boom instructions

Manfrotto

Manfrotto Mega Boom instructions

birzman BM20-FX-STAND quick start guide

birzman

birzman BM20-FX-STAND quick start guide

Wharfedale Pro WLA-28F user manual

Wharfedale Pro

Wharfedale Pro WLA-28F user manual

Multibrackets 7350022734500 installation manual

Multibrackets

Multibrackets 7350022734500 installation manual

Roland KS102e manual

Roland

Roland KS102e manual

Sophos XGS 116 instructions

Sophos

Sophos XGS 116 instructions

Techly ICA-LCD 500BK Installation instruction

Techly

Techly ICA-LCD 500BK Installation instruction

Kimex 015-3002 installation manual

Kimex

Kimex 015-3002 installation manual

FITUEYES TT106501GB quick start guide

FITUEYES

FITUEYES TT106501GB quick start guide

CHIEF PSMA800 installation instructions

CHIEF

CHIEF PSMA800 installation instructions

Lampa 15957 quick start guide

Lampa

Lampa 15957 quick start guide

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.