Luna 850 V GOLD GAS Technical manual

LUNA 850 V GOLD GAS
INSTRUCTION FOR INSTALLATION AND USE
Passion for fire

INSTALLATIEVOORSCHRIFT EN GEBRUIKSAANWIJZING - LUNA 1000-1300-1600 H GOLD - GAS INSRUCTION D’INSTALLATION ET D’UTILISATION - LUNA 1000 -1300-1600 H GOLD - GAZ M-DESIGN
2
SUMMARY
1. GENERAL REMARKS ..............................................................................................................3
2. CONNECTION ..........................................................................................................................3
3. SPECIFICATION SHEET .........................................................................................................4
4. ASSEMBLY OF THE CHIMNEY ............................................................................................5-7
5. ELECTRICAL CONNECTION .................................................................................................8
6. INSULATION AND FINISHING ...........................................................................................8
7. POSITIONING THE LOGS, DIAMOND, SAPPHIRE AND WHITE PEBBLES ..........9
8. FIRST-TIME USE…..............................…………………………………………......................10
9. SAFETY, ADVICE AND MAINTENANCE ..........................................................................10
10.GUARANTEE………………..............……………………………………………...................11
APPENDIX:
Instructions for use of the remote control

INSTALLATIEVOORSCHRIFT EN GEBRUIKSAANWIJZING - LUNA 1000-1300-1600 H GOLD - GAS INSRUCTION D’INSTALLATION ET D’UTILISATION - LUNA 1000 -1300-1600 H GOLD - GAZ M-DESIGN
3
1. GENERAL REMARKS
This is a moulding of the closed combustion system, designed for the atmosphere and comfort of your living-room. It constitutes an efficient source of heat and gives the
impression of a real chimney fire.
The gas with air-vent furnaces are based on the principle of natural extraction from the furnace, which eliminates flue gas outside and brings in air (oxygen) from outside
the house which is necessary for combustion of the gas. It uses to this effect two concentric pipes. The internal pipe ensures the elimination of burned gases and the ex-
ternal pipe brings in combustion air. The advantage of this principle is that the equipment works independently of the atmosphere which predominates in the house.
2. CONNECTION
This appliance must be connected by an approved installer in accordance with the most recent regulations in force. On the basis of your order specifications, this appli-
ance is designed for natural or propane gas.
Read the instructions before installing and using this appliance. Before installing the furnace, please check the local regulations about this type of furnace (identification
of the type of gas, etc.) and check that the furnace is adapted to your means of installation.
CAUTION: The furnace must be connected to the type of gas mentioned on the appliance. Never connect a propane burner to natural gas or vice versa!
It is imperative that the installer sees to the following:
• The appliance must be subject to a water tightness test of the gas and elimination of flue gases.
• The concentric pipe, if already available, must be working correctly.
• The running of the control valve, lighting of the pilot light, the main burner and the thermocouple must all be checked.
This appliance has been programmed and factory sealed. The sealed parts cannot be modified. The appliance may therefore also be installed in watertight accommodation
and accommodation equipped with mechanical ventilation. It constitutes ambient heating even in accommodation equipped with a closed ventilation system.

INSTALLATIEVOORSCHRIFT EN GEBRUIKSAANWIJZING - LUNA 1000-1300-1600 H GOLD - GAS INSRUCTION D’INSTALLATION ET D’UTILISATION - LUNA 1000 -1300-1600 H GOLD - GAZ M-DESIGN
4
3. SPECIFICATION SHEET
Type of Gas NATURAL GAS BUTANE-PROPANE / LPG
Category I2H I2L I2E+ I2E I3+ I3B/P
Category G25 G20 G31 G30
Type C11 , C31 , C31S C11 , C31 , C31S C11 , C31 , C31S C11 , C31 , C31S
Entry pressure (mbar) 25 20 30 37 50 28-30
Burner pressure (mbar) 23.8 19,3 29 36 36 28,2
Consumption (m3/h) 1.132 0,789 0,344 0,389 0,389 0,295
Burner injector Fr./Re.* 6 x 0,80 / 6x0.75 6 x 0,80 / 6 x 0,5 6 x 0,6 6 x 0,6 6 x 0,6 6 x 0,6
Pilot light injector 38/33A 38/33A 0.20P3 0.20P3 0.20P3 0.20P3
Output (%) 87 87,1 74 74 74 74
Nominal load (KW) 9,2 9,7 9,5 9,5 7,0 7,0
Output power (KW) 8,0 8,4 4,7 5,3 5,3 5,3
Emission classification NOX 5 5 5 5 5 5
Output category EC 1 1 2 2 2 2
LUNA 850 V Gold gas
Fr/Re : front / rear

INSTALLATIEVOORSCHRIFT EN GEBRUIKSAANWIJZING - LUNA 1000-1300-1600 H GOLD - GAS INSRUCTION D’INSTALLATION ET D’UTILISATION - LUNA 1000 -1300-1600 H GOLD - GAZ M-DESIGN
5
C
FIG. 1
Fig. 1 ROOF EXIT ( C31 )
NATURAL GAS
Ø 200/130
Appliance
C (min) C (max) Restrictie HR+ (from 3m)
LUNA 850 V 2 m 10m Ø 60
Ø 150/100
Appliance
C (min) C (max) Restrictie HR+ (from 4m)
LUNA 850 V 2 m 18m Ø 60
TAB. 2 This is recommanded with a roof exit < 3m
4. INSTALLING THE CHIMNEY
The only authorised pipes are ONTOP Metaloterm™.
Between the external wall of the pipe and the wall or the ceiling, you should anticipate for an interstice of at least 50mm and protection that is suitable against temperatures of
around 130°C.
The passage of the front panel cowl in the external wall must be filled in using silicone mastic.
TAB. 1 This is recommanded with a roof exit > 3m
ROOF EXIT VIA EXISTING CHIMNEY (C31S) : see TAB.1 & TAB.2

INSTALLATIEVOORSCHRIFT EN GEBRUIKSAANWIJZING - LUNA 1000-1300-1600 H GOLD - GAS INSRUCTION D’INSTALLATION ET D’UTILISATION - LUNA 1000 -1300-1600 H GOLD - GAZ M-DESIGN
6
FIG. 2
Fig. 2 ROOF EXIT VIA EXISTING CHIMNEY (C31S)
AARDGAS
 200(min) Ø 130
Toestel / Appareil
C (min) C (max) Restriction HR+ (from 3m)
LUNA 850 V 2 m 10m Ø 60
 150(min) Ø 100
Toestel / Appareil
C (min) C (max) Restriction HR+ (from 4m)
LUNA 850 V 3 m 18m Ø 60
TAB. 1
TAB. 2
It is obligatory to use the sanitation set USSAN with placing.

INSTALLATIEVOORSCHRIFT EN GEBRUIKSAANWIJZING - LUNA 1000-1300-1600 H GOLD - GAS INSRUCTION D’INSTALLATION ET D’UTILISATION - LUNA 1000 -1300-1600 H GOLD - GAZ M-DESIGN
7
A
B
FIG. 3
Fig. 3 WALL EXIT (C11)
USVK13 - Reduction 200/130 →150/100
Ø 200/130
Appliance A (min) B (min) Restriction HR+ B (max)
LUNA 850 V 1,25m wall exit Ø 70 A+8m
Ø 150/100*
Appliance A (min) B (min) B (max) Restriction HR+
LUNA 850 V 1,25m wall exit A+0,5m Ø 75
(A) Ø 200/130
in combination with.
(B) Ø 150/100*
Appliance A (min) B (min) B (max) Restriction HR+
LUNA 850 V 1,25m wall exit A+ ”USVK13” +4m ----------
* with reduction part USVK13 on the appliance
* with reduction part USVK13 placed horizontally after 90° bend.

INSTALLATIEVOORSCHRIFT EN GEBRUIKSAANWIJZING - LUNA 1000-1300-1600 H GOLD - GAS INSRUCTION D’INSTALLATION ET D’UTILISATION - LUNA 1000 -1300-1600 H GOLD - GAZ M-DESIGN
8
C
B
A
FIG. 4
Fig. 1 ROOF EXIT with 90° bends
Ø 150/100*
Appliance
A (min) B (max) C (min) (A+B+C )max
LUNA 850 V 1,25 m A+C B-A 16m
* with reduction part USVK13 on appliance
Ø 200/130
Appliance
A (min) B (max) C (min) (A+B+C )max
LUNA 850 V 1,25 m (A+C) + 7m B-A-9m 20m
CAUTION : if the vertical lenght is over 3 meter longer than the horizontal lenght, you will
need to place a reduction ring of Ø 60.
Appliance Ø 150/100 and Ø 200/130
LUNA 850 V for each 90° bend substract 1 m horizontaly or add 1 m verticaly.
LUNA 850 V for each 45° / 30° / 15° bend substract 0,5 m horizontaly or add 1 m
verticaly.

INSTALLATIEVOORSCHRIFT EN GEBRUIKSAANWIJZING - LUNA 1000-1300-1600 H GOLD - GAS INSRUCTION D’INSTALLATION ET D’UTILISATION - LUNA 1000 -1300-1600 H GOLD - GAZ M-DESIGN
9
5. ELECTRICAL CONNECTION
This appliance is supplied with a remote-control. Please have a 230V power point ready with an earthing device.
6. INSULATION AND FINISHING
Once installation is complete, the appliance can be fi�ed. Before doing so, check the tightness of the gas pipe one more time. Light the appliance
and check that it is working: check the tightness of the gas pipe and the smoke pipe. Once you have checked everything, you can perform the final
insulating and finishing operations.
The built-in part of the furnace tends to be very warm. Please check that the furnace is not too narrowly fi�ed and that there is adequate space for
the elimination of hot air. For insulation of the furnace, we advise you to use M Design insulating plates. You are advised against using any other
insulation product. Inflammable materials as well may not be used for the finishing.
The enclosure of the furnace must be provided with ventilation grills or openings allowing for the elimination of heat by convection. It is possible
to have a convection kit fi�ed with the furnace. This system directs the heat inside the room by means of flexible tubes.
For the elimination of hot air and the entry of warm air we advise you to use the Design grills by M-Design.
The masonry must be raised around the furnace. Because of the expansion of the furnace during combustion, an interstice of at least 2mm must
be provided on each side of the appliance. The masonry must not lean against the furnace

INSTALLATIEVOORSCHRIFT EN GEBRUIKSAANWIJZING - LUNA 1000-1300-1600 H GOLD - GAS INSRUCTION D’INSTALLATION ET D’UTILISATION - LUNA 1000 -1300-1600 H GOLD - GAZ M-DESIGN
10
9
12 3 4 5
678
0
INSTALLATIEVOORSCHRIFT EN GEBRUIKSAANWIJZING - LUNA 850 V GOLD - GAS INSRUCTION D’INSTALLATION ET D’UTILISATION - LUNA 850 V GOLD - GAZ M-DESIGN
10
7. PUTTING IN PLACE THE LOGS, DIAMOND, SAPPHIRE AND WHITE STONES
• Please check that the pilot light is switched off and that the furnace has cooled down.
• Move the window to the front by pulling it. The window tips open at 45°.
• Arrange the materials supplied. In accordance with your order you will have either a set of logs, diamond, sapphire or white pebbles. There
is an adequate supply of materials . Our appliance is approved with these materials, so please do not use other products. Other decorative products
are prohibited in our appliances. Please do not change the delivered quantities.
ARRANGING THE SET OF LOGS
Caution: do not put anything on the pilot light. To arrange the logs respect the order as follows.

INSTALLATIEVOORSCHRIFT EN GEBRUIKSAANWIJZING - LUNA 1000-1300-1600 H GOLD - GAS INSRUCTION D’INSTALLATION ET D’UTILISATION - LUNA 1000 -1300-1600 H GOLD - GAZ M-DESIGN
11
8. FIRST-TIME USE
The masonry and plaster surrounding a recently installed furnace hold a great deal of moisture, which must first evaporate before commissioning the
appliance. If not, the plaster may crack or split. Ask your installer about the timescale to follow. The first time you use it, only make a moderate-sized
fire.
The first few times the furnace is used, an unpleasant odour may be apparent. It comes from the protective paintwork. These emissions are totally
harmless. To quickly get rid of these odours, all you need to do is ventilate the room for a while.
After the first few fires, a light deposit may appear on the window. It comes from the paintwork. Once the furnace is cold you can get rid of this de-
posit by using M Design’s Bio-Clean cleaning product. This product may be used later on for cleaning the window.
The appliance must not be used if the door no longer has a window or with the door open. If the window is broken or cracked, the appliance must
not be used until the window has been replaced. Contact your M Design reseller.
9. SAFETY, ADVICE AND MAINTENANCE
Have your furnace inspected once a year by a qualified technician.
Please observe the following points:
• Closed appliances produce intense heat, which means that all the surfaces of the external walls (metal, door frames and windows) become very
hot once a certain temperature is reached. Make sure that young children do not touch the window; this could result in severe burns.
• The logs, ceramic pebbles, a Diamond set and a Sapphire set are delivered with the furnace. Never put other objects in the flames!
• Keep inflammable materials a suitable distance from the furnace (min. 1m)!
• Never modify the se�ings yourself! The furnace warranty will then be considered as invalid, null and void.
• Never let children use the remote control without supervision.
• Always leave the pilot light on. The appliance is designed in order that the pilot light goes out automatically every 24 hours and lights in-
stantly. This enables the electronic system to run down from static electricity.
• In the case where the burner goes out for any reason, wait for 3 minutes before relighting the furnace.

INSTALLATIEVOORSCHRIFT EN GEBRUIKSAANWIJZING - LUNA 1000-1300-1600 H GOLD - GAS INSRUCTION D’INSTALLATION ET D’UTILISATION - LUNA 1000 -1300-1600 H GOLD - GAZ M-DESIGN
12
10. GUARANTEE
This page is your warranty card.
The guarantee is only valid for faults caused by construction defects or defects in the parts used to build the furnace.
M-Design offers a 12 month guarantee on all electronic parts and a 6 year guarantee on the furnace construction.
Caution: The following items are always excluded from the guarantee:
- The glass, door, joints and internal decor.
- The defects which occur are fully or partially a consequence of
• Non respect of the order, installation and maintenance instructions
• Assembly, installation or repair by a third-party, including the buyer
• Heat cracks which normally occur in the mantel
• In cases where changes have been made to the furnace without our consent
• In cases where the buyer cannot show his/her warranty card with the purchase invoice. Likewise where the guarantee and/or the invoice
show(s) signs of tampering or forgery (crossed out date, illegible, modifications).
In the case you would like to make use of the manufacturer’s warranty, you should contact your reseller in the first instance. Please take good care
of your purchase invoice and warranty card and store them in a safe place.