Lux Products PurePro Everything'Stat DP722 User manual

1. FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.
COMPATIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.1.
HEAT STAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.2.
COOLING/COMPRESSOR STAGES . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.3.
ELECTRICAL RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3.
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3.1.
TOOLS REQUIRED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
3.2.
LOCATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.3.
REMOVAL OF OLD UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.4.
MOUNTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.5.
WIRING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.5.1 TERMINAL DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.5.2 FREEZE PROTECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.5.3 SPECIAL WIRING NOTES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.5.4 COMMON WIRING OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3.5.5 SINGLE STAGE HEATING SYSTEMS LABEL CROSS REFERENCE. . . . . 4
3.5.6 SINGLE STAGE COOLING SYSTEMS LABEL CROSS REFERENCE . . . . 4
3.5.7 SINGLE STAGE FURNACE HEATING AND SINGLE STAGE
COOLING SYSTEM LABEL CROSS REFERENCE . . . . . . . . . . . . . . . . . . 4
3.5.8 TWO STAGE HEAT, SINGLE STAGE COOL HEAT PUMP SYSTEM
LABEL CROSS REFERENCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.5.9 WIRING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.6.
INSTALL BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.7.
INSTALLER SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.7.1 ACCESS AND NAVIGATE INSTALLER SETUP MENU . . . . . . . . . . . . . . . 9
3.7.2 INSTALLER SETUP MENU WITH
FURNACE SYSTEM TYPE SELECTED: . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.7.3 INSTALLER SETUP MENU WITH HEAT
PUMP SYSTEM TYPE SELECTED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.7.4 COMPLETING YOUR INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.1.
OPERATING BASICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.1.1 UP/DOWN ARROW CHANGE KEYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.1.2 SET DAY AND TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.1.3 DEFAULT PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.1.4 MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.1.5 DISPLAY ILLUMINATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.2.
USER SETUP MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.2.1 ACCESS AND NAVIGATE USER SETUP MENU. . . . . . . . . . . . . . . . . . . . 12
4.2.2 KEYBOARD LOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.2.3 BEEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.2.4 TEMPERATURE DISPLAY FORMAT (F/C DISPLAY) . . . . . . . . . . . . . . . . 13
4.2.5 CLOCK FORMAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2.6 CALIBRATION OFFSET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2.7 MAXIMUM HEAT SETTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2.8 MINIMUM COOL SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2.9 SMART RECOVERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2.10 FILTER LIMIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2.11 USER SETUP MENU: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3.
ADVANCED FEATURES AND OPERATION . . . . . . . . . . . . . . . . . . . . 13
4.3.1 EMERGENCY HEAT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3.2 FAN MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.3.3 VACATION HOLD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.3.4 DAYLIGHT SAVINGS TIME ADJUSTMENT (DST) . . . . . . . . . . . . . . . . . 14
4.3.5 AIR FILTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.3.6 ENERGY USAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.3.7 FUTURE OUTDOOR SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.3.8 FUTURE REMOTE INDOOR SENSORS . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.3.9 RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.4.
PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.4.1 WEEKDAY TEMPERATURE PROGRAMMING. . . . . . . . . . . . . . . . . . . . . 15
4.4.2 WEEKDAY FAN PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.4.3 WEEKEND PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4.4.4 COPY PROGRAMMING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.
BATTERIES/MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.1.
BATTERY INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.
TECHNICAL DETAILS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
6.1.
STAGING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.
TECHNICAL ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
8.
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
PUREPRO EVERYTHING’STAT®DP722
INSTALLATION AND OPERATING INSTRUCTIONS
Mt. Laurel, New Jersey 08054, USA lwww.luxproproducts.com
DP722
WARNING: Use Energizer®or DURACELL®Alkaline Batteries Only.
Energizer®is a registered trademark of Eveready Battery Company, Inc.
DURACELL®is a registered trademark of The Gillette Company, Inc.
52119

1. FEATURES
●
Universal Compatibility
●
Controls Up To 2 Stages Of Heat And 2 Stages Of
Cooling + Auxiliary and Emergency Heat
●
Large Hybrid Display
●
Auxiliary and Emergency Heat Indicators
●
Electro-luminescent Display Backlight
●
Clean Cycle®(Patent No. 6,988,671)
Independently Programmable Fan
●
7 Day Programming
●
Default Program
●
4 Periods Per Day
●
Temporary Override
●
Temperature Hold
●
Optional Smart Recovery
●
Programmable Filter Timer With Change
Filter Indicator
●
Energy Usage Monitor
●
F/C Temperature Display
●
12/24 Hour Clock
●
Easy Programming with LUX Speed Dial®
●
Advanced Copy Function For Fast Easy Programming
●
Nonvolatile Memory For All Programs And Settings
●
Daylight Saving Button
●
Multimode Keyboard Lockout With User
Programmable 3 Digit Code
●
Programmable High And Low Setting Limits
●
Silence-able Audible Button Response
●
Menu Driven Setup Done From The Front Panel
●
Temperature Offset (User Calibration)
●
Dual Power Capable (System/Battery)
●
Multi-Stage Adjustable Temperature Differential /
Cycle Rate
●
Programmable Length Minimum Run Time
●
Programmable Auto-Changeover Dead-Band
●
Programmable Fan Delays For Heat, Cool, In Both
On And Off
2. COMPATIBILITY
Your DP722 is compatible with most 24 volt gas, oil, or
electrical Heating and/or Cooling systems. It cannot be
used with 120 volt heating systems. Ask your dealer for
other PurePro thermostats to control those systems.
2.1. HEAT STAGES
The DP722 is capable of controlling systems with up to
two stages of heat in furnace mode. In heat pump mode,
the thermostat can be configured to control up to two
stages of compressor driven heat plus auxiliary and
emergency heat stages.
NOTE: AUX HEAT ACTIVATION IS PROVIDED AT
TERMINAL W1
2.2. COOLING/COMPRESSOR STAGES
The DP722 is capable of controlling systems with up to
two stages of cooling.
2.3. ELECTRICAL RATINGS
●
30V maximum (24VAC nominal)
●
1.5A maximum per terminal
●
2.0A terminal sum
3. INSTALLATION
3.1. TOOLS REQUIRED
●
#1 Phillips screwdriver (small)
●
Drill with 3/16-in. (4.8mm) bit
●
Wire stripper/cutter
3.2. LOCATION
2
COPY FAN
MODE
NEXT
NEXT
RUN
DST Setup
Auto On
SET WEEKEND
PROGRAMS
SET WEEKDAY
PROGRAMS SET DAY
AND TIME
AIR
FILTER
ENERGY
USAGE
Auto Heat Off Cool
UP
LARGE HYBRID DISPLAY
WITH ELECTRO-LUMINESCENT
DISPLAY BACKLIGHT
EASY
PROGRAMMING
WITH
LUX SPEED DIAL®
DOWN
IAQ
INDEPENDENTLY
PROGRAMMABLE
FAN
MENU DRIVEN
SETUP
DP722

On replacement installations, mount the new thermostat
in place of the old one unless the conditions listed below
suggest otherwise. On new installations, follow the
guidelines listed below.
●
Do not locate in a damp area. This can lead to corro-
sion that will shorten thermostat life.
●
Do not locate where air circulation is poor, such as in a
corner or an alcove; or behind an open door.
●
Do Locate the thermostat on an inside wall, about 5 ft.
(1.5m) above the floor, and in a room that is used often.
●
Do not install it where there are unusual heating condi-
tions, such as: in direct sunlight; near a lamp, radio, tele-
vision, radiator, register, or fireplace; near hot water pipes
in a wall; near a stove on the other side of a wall.
●
Do not locate in unusual cooling conditions, such as:
on a wall separating an unheated room; or in a draft from
a stairwell, door, or window.
●
Do not install the unit until all construction work and
painting has been completed.
3.3. REMOVAL OF OLD UNIT
CAUTION: Read instructions carefully before removing any
wiring from existing thermostat. Wires must be labeled
before they are removed. When removing wires from their
terminals, ignore the color of the wires since they may not
comply with any standard.
●
Switch electricity to the furnace and air conditioner
OFF; then proceed with the following steps.
●
Remove cover from old thermostat. Most are snap-on
types and simply pull off. Some have locking screws on
the on the side. These must be loosened.
●
Note the letters printed near the terminals. Attach
labels (enclosed) to each wire for identification. Label and
remove wires one at a time. Make sure the wires do not
fall back inside the wall.
●
Loosen all screws on the old thermostat and remove it
from the wall.
3.4. MOUNTING
CAUTION: Be careful not to drop the unit or disturb electronic
parts.
●
Strip insulation 3/8 in. (9.5mm) from wire ends and
clean off any corrosion.
●
Fill wall opening with non-combustible insulation to
prevent drafts from affecting the thermostat.
●
With each thumb on a release tab at the bottom of the
body, and fingers over the top of the unit. Release the
unit from its base plate by squeezing the tabs into the
body.
●
Separate the unit from its base plate by pulling the
body outward from the bottom.
NOTE: If you are mounting the base to a soft material like
plasterboard or if you are using the old mounting holes, the
screws may not hold. Drill a 3/16-in. (4.8mm) hole at each
screw location, and insert the plastic anchors provided. Then
mount the base as described below.
●
Route the wires through the open areas in the base
plate above the terminals. Hold the base against the wall,
with the wires coming through. Position the base for the
best appearance (to hide any marks from an old thermo-
stat). Attach the base to the wall with the two screws pro-
vided.
3.5. WIRING
3.5.1 TERMINAL DEFINITIONS
Terminal Definition
1 G Fan
2
O Cooling Mode
3
Y2 Second stage cool
4
Y1 First stage cool
5
RC Cooling power source (transformer +)
6
C Common, system power -
7
RH Heating power source (transformer +)
8
W1 First stage heat
9
W2 Second stage heat
10
E Emergency heat/Freeze protection
11
B Heating Mode
12
TC Future Indoor temperature input -
13
T Future Indoor temperature input +
14
OT Future Outdoor temperature sensor
input (a)
15
OT Future Outdoor temperature sensor
input (b)
1. G The fan terminal is live at any time the
thermostat attempts to turn the system fan or
blower on.
2. O This terminal is live at any time the unit is
in Cool mode.
3. Y2 Activation of this terminal signifies that the
thermostat is calling for a second stage of cooling.
This terminal will remain inactive unless a second
stage compressor has been specified in the
installer setup menu.
4. Y1 Activation of this terminal signifies that the
thermostat is calling for a first compressor stage.
This terminal will remain inactive unless at least
one compressor stage has been specified in the
installer setup menu.
5. RC This terminal provides power to the cooling
and fan terminals.
6. C Use of this terminal allows the unit to be
system powered rather than battery powered. Note
that the display backlight is battery powered only.
7 RH This terminal provides power to the heating
terminals.
8. W1 This terminal is active when the thermostat
is calling for the first available stage of furnace or
electric heat. It will remain inactive unless at least
one stage of furnace type heat has been specified
in the installer setup menu.
3

9. W2 This terminal is active when the thermostat
is calling for a second stage of furnace or electric
heat. It will remain inactive unless two stages of
heating have been specified in the installer setup
menu.
10. E This terminal is active when the thermostat
is calling for Emergency heat in a heat pump sys-
tem. This terminal also powers freeze protection if
it is desired. It will be active below 40°F(5°C)
regardless of mode or battery condition or other
unforeseen condition.
11. B This terminal is live at any time the unit is
in Heat mode.
12. TC Future indoor temperature sensor common.
May be wired to a maximum of three external
indoor sensor units.
13. T Future indoor temperature sensor. May be
wired to a maximum of three external indoor sen-
sor units.
14. OT Future first of two terminals dedicated to
the outdoor temperature sensor. Polarity of these
leads does not matter.
15. OT Future second of two terminals dedicated to
the outdoor temperature sensor. Polarity of these
leads does not matter.
3.5.2 FREEZE PROTECTION
The DP722 incorporates a mechanical thermal switch
which may be used to prevent a freeze-up by calling for
heat in the event the unit has accidentally been turned off
or its batteries have not been replaced as recommended.
●
This switch is available at the E terminal of the thermo-
stat. In most systems using this feature will require
wiring a jumper between the W1 and E terminals. The
thermostat will call then for the first stage of heat, in fur-
nace mode, or Aux heat in heat pump mode. See EMER-
GENCY HEAT.
●
The nominal temperature set point of this switch is
40°F(5°C).
3.5.3 SPECIAL WIRING NOTES
●
In heat pump mode, AUX heat is available at W1.
●
In heat pump mode, Emergency Heat is activated from
the E terminal. This terminal also provides freeze protec-
tion and it will be active below a nominal temperature of
40°F(5°C).
3.5.4 COMMON WIRING OPTIONS
Though not shown here additional second stages may be
used where applicable. Be sure to enable them properly
in the Installer Setup menu.
W2 is second stage heat
E is emergency heat and freeze protection
Y2 is second stage cool or second stage heat pump
OPTIONAL O or B terminals may be used to power heat-
ing dampers or changeover valves in any system config-
uration.
OPTIONAL C terminal may be connected to a system
common to power the thermostat from the system in any
wiring configuration.
WARNINGS: 1. A B wire is sometimes used as a
common wire. Connecting a common B wire to the B termi-
nal in these systems will likely cause damage to the thermo-
stat and/or HVAC system. Do not connect a wire to the B ter-
minal if you are unsure whether it may be wired to a system
common.
2.If Both Y and C wire are present, then C is common. Tape it
off or connect it to the C terminal to allow the system to
power the thermostat.
OPTIONAL C, X, B, TC C Transformer Common
B B Changeover Valve
O O Use O or B not both
3.5.5 SINGLE STAGE HEATING SYSTEM LABEL CROSS
REFERENCE
Previous Thermostat New Thermostat
System Terminal Marking Terminals Wire To
All 2 Wire Heat RH, R, RC, V, 5 RH Transformer
W, H, 4 W1 Heating Valve
3 Wire RH, R, RC, V, 5 RH Transformer
W, 4 W1 Heat Control
B, C Tape Off * *
3 Wire
(one wire is "F or G") RH, R, 5, V RH Transformer
W, 4 W1 Heating Valve
G, F G Fan Relay
3.5.6 SINGLE STAGE COOLING SYSTEM LABEL CROSS
REFERENCE
Previous Thermostat New Thermostat
System Terminal Marking Terminals Wire To
2 Wire RC, R, V RC Transformer
Y, Y1, C Y1 Cooling Relay
3 Wire RC, R, V RC Transformer
Y, Y1, C Y1 Cooling Relay
G, F G Fan Relay
3.5.7 SINGLE STAGE FURNACE HEATING AND SINGLE
STAGE COOLING SYSTEM LABEL CROSS REFERENCE
Previous Thermostat New Thermostat
System Terminal Marking Terminals Wire To
4 Wire
(heat & cool with
single transformer) RH, RC, R, V RH & RC, w jumper Transformer
W, W1 W1 Heating Relay
Y, Y1, C Y1 Cooling Relay
G,F G Fan Relay
5 Wire
(heat & cool with
two transformers) RH RH Heating Transformer
RC RC Cooling Transformer
W, W1 W1 Heating Relay
Y, Y1, C Y1 Cooling Relay
G,F G Fan Relay
4

3.5.8 TWO STAGE HEAT, SINGLE STAGE COOL, HEAT
PUMP SYSTEM LABEL CROSS REFERENCE
Previous Thermostat New Thermostat
System Terminal Marking Terminals Wire To
Heat Pump
2 Heat, 1 Cool RH, RC, R, V RH & RC, w jumper Transformer
Y, Y1, C Y1 Compressor Relay
W, W2 W1 Aux Heat Relay
E E Em Heat/Freeze Prot
B B* *Changeover Valves
O O* Use O or B not both
G,F G Fan Relay
3.5.9 WIRING DIAGRAMS
5
G O Y2 Y1 RC C RH W1 W2 E B
TYPICAL 2 WIRE HEAT HOOKUP
24 VAC AND MILLIVOLT SYSTEMS
XFMR GAS
VALVE
AC LINE
SYSTEM TYPE = FURNACE
[01]
HEAT STAGES =1
[02]
COMPRESSOR STAGES = 0
[03]
MODES = Heat-Off
[04]
HEAT FAN CONTROL
= GAS
[09]
TYPICAL INSTALLER SETUP:
OPTIONAL COMMON
ALLOWS USE OF
SYSTEM POWER
[1]
NOTES:
JUMPER
PROVIDED
SYSTEM
COMMON
G O Y2 Y1 RC C RH W1 W2 E B
TYPICAL 24VAC 3 WIRE HEAT HOOKUP
WHERE 3RD WIRE IS FAN WIRE
FAN XFMR GAS
VALVE
AC LINE
TYPICAL INSTALLER SETUP:
OPTIONAL COMMON
ALLOWS USE OF
SYSTEM POWER
[1]
NOTES:
JUMPER
PROVIDED
SYSTEM
COMMON
SYSTEM TYPE = FURNACE
[01]
HEAT STAGES =1
[02]
COMPRESSOR STAGES = 0
[03]
MODES = Heat-Off
[04]
HEAT FAN CONTROL
= GAS
[09]

6
G O Y2 Y1 RC C RH W1 W2 E B
TYPICAL 24VAC 4 WIRE HOOKUP
SINGLE STAGE HEATING AND COOLING
FAN XFMRCOMPRESSOR GAS
VALVE
AC LINE
TYPICAL INSTALLER SETUP:
JUMPER
PROVIDED
SYSTEM COMMON
SYSTEM TYPE = FURNACE
[01]
HEAT STAGES =1
[02]
COMPRESSOR STAGES = 1
[03]
MODES = Ht-Off-Cl-Auto
[04]
HEAT FAN CONTROL
= GAS
[09]
OPTIONAL COMMON
ALLOWS USE OF
SYSTEM POWER
[1]
NOTES:
G O Y2 Y1 RC C RH W1 W2 E B
TYPICAL 5 WIRE HOOKUP
SINGLE STAGE HEATING AND COOLING
COOLING
XFMR 1
FAN GAS
VALVE
HEATING
XFMR 2
AC LINE AC LINE
COOL
COMMON
COMPRESSOR
TYPICAL INSTALLER SETUP:
SYSTEM TYPE = FURNACE
[01]
HEAT STAGES =1
[02]
COMPRESSOR STAGES = 1
[03]
MODES = Ht-Off-Cl-Auto
[04]
HEAT FAN CONTROL
= GAS
[09]
OPTIONAL COMMON
ALLOWS USE OF
SYSTEM POWER
[1]
NOTES:

7
G O Y2 Y1 RC C RH W1 W2 E B
TYPICAL SINGLE-STAGE HEAT PUMP WITH
(2 STAGES HEAT AND 1 STAGE COOL)
OPTIONAL AUX AND EMERGENCY HEAT
FAN SYSTEM
XFMR
COMPRESSOR AUX/EM
HEAT
REVERSING
VALVE
AC LINE
OPTIONAL COMMON
ALLOWS USE OF
SYSTEM POWER
USE "B" OR "O" BUT
NOT BOTH
AUX HEAT AND
EMERGENCY HEAT
ARE OPTIONAL
[1]
[2]
[3]
NOTES:
JUMPER
PROVIDED
SYSTEM COMMON
TYPICAL INSTALLER SETUP:
SYSTEM TYPE = HEAT PUMP
[01]
HEAT STAGES =1
[02]
COMPRESSOR STAGES = 1
[03]
MODES = Ht-Off-Cl-
EmHt-Auto
[04]
HEAT FAN CONTROL
= ELECTRIC
[09]
G O Y2 Y1 RC C RH W1 W2 E B
USE 2 SEPARATE SINGLE STAGE HEATERS
AS A 2 STAGE HEAT SYSTEM
SYSTEM
XFMR 1
HEATER
1
HEATER
2
SYSTEM
XFMR 2
AC LINE AC LINE
SYSTEM 1
COMMON SYSTEM 2 COMMON
OPTIONAL COMMON
ALLOWS USE OF
SYSTEM POWER
[1]
NOTES:
TYPICAL INSTALLER SETUP:
SYSTEM TYPE = HEAT PUMP
[01]
HEAT STAGES =1
[02]
COMPRESSOR STAGES = 1
[03]
MODES = Heat-Off
[04]
HEAT FAN CONTROL
= ELECTRIC
[09]

8
G O Y2 Y1 RC C RH W1 W2 E B
MULTI-STAGE FURNACE HEAT
AND COOLING HOOKUP
FAN COOLING
XFMR
HEATING
XFMR
HEATER
AIR CONDITIONER
STAGE 2
COMPRESSOR
STAGE 1
COMPRESSOR
AC LINE AC LINE
OPTIONAL COMMON
ALLOWS USE OF
SYSTEM POWER
EITHER SECOND
STAGE MAY BE
OMITTED
[1]
[2]
NOTES:
STAGE
1
STAGE
2
COOL
COMMON
HEAT
COMMON
TYPICAL INSTALLER SETUP:
SYSTEM TYPE = FURNACE
[01]
HEAT STAGES
=(MATCH SYSTEM)
[02]
COMPRESSOR STAGES
= (MATCH SYSTEM)
[03]
MODES = Ht-Off-Cl-Auto
[04]
HEAT FAN CONTROL
= ELECTRIC
[09]
G O Y2 Y1 RC C RH W1 W2 E B
TYPICAL MULTI-STAGE STAGE HEAT PUMP WITH
OPTIONAL AUX AND EMERGENCY HEAT
(2 OR 3 STAGES HEAT, 2 STAGES COOL)
FAN SYSTEM
XFMR
AUX/EM
HEAT
REVERSING
VALVE
HEAT PUMP
STAGE 2
COMPRESSOR
STAGE 1
COMPRESSOR
AC LINE
JUMPER
PROVIDED
SYSTEM COMMON OPTIONAL COMMON
ALLOWS USE OF
SYSTEM POWER
USE "B" OR "O" BUT
NOT BOTH
AUX HEAT AND
EMERGENCY HEAT
ARE OPTIONAL
[1]
[2]
[3]
NOTES:
TYPICAL INSTALLER SETUP:
SYSTEM TYPE = HEAT PUMP
[01]
HEAT STAGES
= MATCH SYSTEM
[02]
COMPRESSOR
STAGES = MATCH SYSTEM
[03]
MODES = Ht-Off-Cl-
EmHt-Auto
[04]
HEAT FAN CONTROL
= ELECTRIC
[09]

3.6. INSTALL BATTERIES
Install batteries at this time. For instructions, see BAT-
TERY INSTALLATION.
3.7. INSTALLER SETUP
Configuration items are selected from the Installer Set up
Menu. They are stored in non-volatile RAM, and will be
preserved even in the event that the unit’s batteries are
run down, or removed, or the hardware reset on the rear
of the unit’s circuit board of the thermostat is pressed.
NOTE: Pressing the S/W RESET button on the rear of the
unit’s circuit board will write default values of all temperature
programs and setup menus into the unit nonvolatile memory.
Take care not to inadvertently press this button when the ther-
mostat has been removed from the wall plate!
3.7.1 ACCESS AND NAVIGATE INSTALLER SETUP
MENU
Note: Insure that all relays are off before making changes in
the installer menu. There are two methods, which may be
used to do this. Place the unit in the OFF mode and wait for 5
minutes or Press the H/W RESET button on the rear of the
unit’s circuit board. Take care not to inadvertently press the
S/W RESET button.
●
To enter the Installer Setup Menu press and hold the
Setup Button for 10 seconds.
●
Use the NEXT button to scroll through its options. As
you proceed the menu item number will be displayed in
the left portion of the screen.
●
Selections can be changed by pressing the UP/DOWN
button.
●
Moving from one menu item to the next and accept-
ance of changes is done by pressing the NEXT button.
●
All changes become effective when the unit exits the
Installer Setup mode.
●
The Installer Setup mode will be exited when the Setup
button is pressed again, or, if no other keys are pressed
for 20 seconds.
All settings, their choices and default values are given in
INSTALLER SETUP MENU WITH FURNACE SYSTEM
TYPE SELECTED: and INSTALLER SETUP MENU WITH
HEAT PUMP SYSTEM TYPE SELECTED AND FUTURE
OUTDOOR SENSOR ENABLED.
3.7.1.1 SYSTEM TYPE
This option determines whether the thermostat is to con-
trol a furnace and air conditioning system or heat pump
system.
●
In furnace mode the unit will make the proper W ter-
minals live for Heating, and the proper Y terminals live
for cooling.
●
In Heat Pump mode the unit makes the proper Y ter-
minals live for the first and second stages of a heat pump
unit during heating or cooling. In this mode an additional
stage of Aux Heat may also be activated through the W1
terminal.
3.7.1.2 HEAT STAGES
Set this to the number of non-compressor driven heat
stages to use for temperature control by this system.
3.7.1.3 COMPRESSOR STAGES (COOL/HEAT PUMP
STAGES)
Set the number of compressor driven system stages to
use for temperature control. These stages include all
cooling or heat pump stages to be used for temperature
control by this system.
3.7.1.4 MODES
The modes setting selects what system modes will be
available to the user. The selections available are system
mode dependant:
●
Heat-Off
●
Cool-Off
●
Heat-Off-Cool
●
Heat-Off-Cool-Auto (Furnace Mode) or
●
Heat-Off-Cool-Em Heat-Auto (Heat Pump Mode)
3.7.1.5 MINIMUM RUN TIME
Minimum Run Time provides compressor protection and
prevents short cycling. Compressor stages are held off
for a minimum of this time. During program run this is
also the minimum on time.
3.7.1.6 HEAT PUMP LOCKOUT
This menu item is available only in Heat Pump Mode with
an operational outdoor temperature sensor. Enabling this
option allows the thermostat to disable a heat pump and
request AUX Heat below the Heat Pump Lockout
Temperature.
3.7.1.7 HEAT PUMP LOCKOUT TEMPERATURE
This menu item is available only in Heat Pump Mode with
an operational outdoor temperature sensor. With it you
may set the outdoor temperature at which the thermostat
will cease to call for heat pump sourced heat, and use the
alternate AUX Heat source.
3.7.1.8 DEADBAND
When using auto-changeover, deadband provides a disal-
lowed temperature range between the maximum heat
temperature set point and minimum cool temperature set
point. Deadband may be set from 3 to 5 degrees. With
auto-changeover active and the Deadband set to 3°F and
heat set to 70°F the minimum allowed cool temperature
set point will be 73°F. If the cool temperature set point is
lowered, then the heat temperature set point will be low-
ered by the same amount maintaining the 3°F Deadband.
3.7.1.9 SWING 1
Swing 1 sets the temperature variation the system allows
above the temperature set point before switching the first
stage heat source off, or below the temperature set point
before switching the first stage heat source on. In Cool,
Swing 1 sets the temperature variation the system allows
above the temperature set point before switching first
stage of cooling on, or below the temperature set point
before switching the first stage of cooling off.
9

3.7.1.10 SWING 2
This value is similar to the Swing 1, but it controls the
temperature variation the system allows above and below
Swing 1’s lower limit before calling for a second stage.
Once a second stage is activated, it will remain on until
the temperature set point has been reached. If a third
stage of heat is present in heat pump mode, Swing 2 is
used to control it from the stage 2 lower limit.
3.7.1.11 HEAT FAN CONTROL
Fossil fuel furnaces normally control the system fan while
the furnace is operating. Electric systems normally
require the thermostat to activate the fan. This setting
instructs the thermostat how to handle fan control during
heating. Electric heat and heat pumps generally require
the thermostat to activate the fan and therefore use the
electric setting.
3.7.1.12 HEAT FAN ON DELAY
This setting allows the installer to program the length of
time between heating activation and fan activation (delay
on make).
3.7.1.13 HEAT FAN OFF DELAY
This setting allows the installer to program the length of
time between heating deactivation and fan deactivation
(delay on break).
3.7.1.14 COOL FAN ON DELAY
This setting allows the installer to program the length of
time between cooling activation and fan activation (delay
on make).
3.7.1.15 COOL FAN OFF DELAY
This setting allows the installer to program the length of
time between cooling deactivation and fan deactivation
(delay on break).
3.7.1.16 FUTURE OUTDOOR SENSOR
This setting enables and disables an outdoor sensor if it
is present. The setting will be held NA if a sensor is not
present, and will be reset to NA If the sensor is discon-
nected for any reason, including removal of the thermo-
stat from its base-plate, the thermostat will automatically
disable the sensor changing the setting in this menu
from ON to NA. With an outdoor sensor present and
enabled, the outdoor temperature will be displayed alter-
nately with time. The word OUT will be visible to the right
of the temperature while the outside temperature is dis-
played.
3.7.1.17 INTERNAL TEMPERATURE SENSOR
This setting enables and disables the thermostats internal
temperature sensor. It may only be disabled if there are
indoor remote sensors present and enabled.
3.7.1.18 FUTURE INDOOR REMOTE SENSOR 1, 2, 3
Used to enable and disable the respective remote sensors
in a system. When more than one indoor sensor is used,
the values of their measurements are averaged for use in
temperature control.
3.7.2 INSTALLER SETUP MENU WITH FURNACE SYS-
TEM TYPE SELECTED:
Menu
Item Display Selections Default
01 System Type Furnace / Heat Pump Furnace
02 Heat Stages 0 – 2 2
03 Compressor Stages 0 – 2 2
04 Modes Heat-Off *
Cool-Off *
Heat-Off-Cool *
Heat-Off-Cool-Auto *Heat-Off-
Cool-Auto
05 Minimum Run Time 1 to 5 min 4 min
06 Deadband 3°F(1°C) to 5°F(3°C) 3°F(1°C)
07 Swing 1 0.25°F(0.15°C) to 2.25°F(1.25°C) 0.25°F(0.15°C)
08 Swing 2 0.25°F(0.15°C) to 2.25°F(1.25°C) 0.5°F(0.3°C)
09 Heat Fan Control Gas / Electric Gas
10 Heat Fan On Delay 0, 15, 30…180 sec 0 sec
11 Heat Fan Off Delay 0, 15, 30…180 sec 0 sec
12 Cool Fan On Delay 0, 15, 30…180 sec 0 sec
13 Cool Fan Off Delay 0, 15, 30…180 sec 0 sec
14 Outdoor Sensor (future) NA/ON/OFF NA/OFF
15 Internal Temp Sensor
(future) ON/OFF ON
16 Remote Sensor 1
(future) NA/ON/OFF NA/OFF
17 Remote Sensor 2
(future) NA/ON/OFF NA/OFF
18 Remote Sensor 3
(future) NA/ON/OFF NA/OFF
3.7.3 INSTALLER SETUP MENU WITH HEAT PUMP
SYSTEM TYPE SELECTED AND OUTDOOR FUTURE
SENSOR ENABLED:
Menu
Item Display Selections Default
01 System Type Furnace / Heat Pump Furnace
02 Heat Stages 0 – 1 1
03 Compressor Stages 0 – 2 1
04 Modes Heat-Off *
Cool-Off *
Heat-Off-Cool *
Heat-Off-Cool- *Heat-Off-Cool-
Em Heat-Auto Em Heat-Auto
05 Minimum Run Time 1 to 5 min 4 min
06* Heat Pump Lockout ON, OFF Off
07* Heat Pump
Lockout Temperature 0°F- 50°F(-17°C-10°C) 0°F(-17°C)
08 Deadband 3°F(1°C) to 5°F(3°C) 3°F(1°C)
09 Swing 1 0.25°F(0.15°C) to 2.25°F(1.25°C) 0.25°F(0.15°C)
10 Swing 2 0.25°F(0.15°C) to 2.25°F(1.25°C) 0.5°F(0.3°C)
11 Heat Fan Control Electric Electric
12 Heat Fan On Delay 0, 15, 30…180 sec 0 sec
13 Heat Fan Off Delay 0, 15, 30…180 sec 0 sec
14 Cool Fan On Delay 0, 15, 30…180 sec 0 sec
15 Cool Fan Off Delay 0, 15, 30…180 sec 0 sec
10