Luxor MB-36 Installation instructions

Zero Clearance Direct Vent Gas Fireplaces
Model MB-36
Installation and Owner’s Manual
Installer: Please leave this manual with the customer
Customer: Please keep instructions for future reference
FOR YOUR SAFETY
DO NOT store or use gasoline or any other
flammable vapors or liquids within the vicinity of
this or any other appliance.
IN THE EVENT THAT YOU SMELL GAS
-Do not try to light any appliance
-Open windows
-Do not touch electrical switches
-Do not use any phone in your building
-Extinguish any open flame
-Call your gas supplier from a neighbors phone
and follow the gas suppliers instructions.
-If you cannot reach the gas supplier, call the fire
department
PLEASE READ INSTRUCTIONS CAREFULLY BEFORE
INSTALLING AND OPERATING THE APPLIANCE
WARNING: If the information in these instructions are not followed exactly, a fire or
explosion may result causing property damage, personal injury, or loss of life.
Installation and service must be performed by a qualified installer, service agency, or the
gas supplier.
This appliance may be installed in a permanent home, and is suitable for bedroom or
sitting room.
PLEASE NOTE: This product has been manufactured using steel and screws. As a
result, there are many sharp edges that can easily cut exposed skin. It is highly
recommended that you wear proper protective gloves while installing the unit, and
during routine cleaning or maintenance..
7057 Beatty Drive British Columbia,
Canada, V2V 6C4
Ph: [phone], [phone], Fax: [phone],
Web: www.firehearth.ca
Canadian Fire Hearth Mfg, Inc

This appliance is only for use with Natural Gas and Propane as indicated
On the rating plate.
Note: The copy in the manual is for reference only. In the event of a discrepancy, the
label on the unit is to be taken as the latest version.
Date Purchased:_________________________________________________
Dealer:_________________________________________________________
Installer:________________________________________________________
Phone:___________________________ Cell:______________________
Serial Number:___________________________________________________
Welcome!
Congratulations on the purchase of your new Luxor Gas Fireplace! We hope
you’ve had an easy and enjoyable time choosing from our line of products, and
we certainly appreciate your business. Please take some time to read through
the following information, and make sure to heed all of the warnings. Even
though our fireplaces are easy to install and simple to operate, they are still gas
burning units with some inherent dangers if not careful.
If you have not already done so, please visit us online at www.firehearth.ca for a
complete guide to the options available for your unit.
Pre-Start Up Checks
FOR YOUR SAFETY - Read before lighting
DO NOT: Use tools to operate controls. Use only you hand to push in and turn controls.
DO NOT: Abuse glass doors by striking or slamming shut.
DO NOT: Clean the appliance when hot.
DO NOT: Use this appliance if you smell gas.
DO NOT: Use this appliance if any part has been under water. Immediately call a qualified service technician to
inspect the appliance and replace any part of the control system and any gas control which has been under water.
DO NOT: Obstruct the flow of ventilation air.
GAS SUPPLY
ONLY PERSONS LICENSED TO WORK WITH GAS PIPING MAY MAKE THE NECESSARY GAS
CONNECTION TO THIS APPLIANCE. YOUARE NOW READY TO HOOK UP THE GAS SUPPLY. BE SURE
GAS PLUMBING INSTRUCTIONS AND ALL PROVINCIALAND LOCAL CODESARE CAREFULLY FOLLOWED.
USE APPROVED FLEXIBLE GAS CONNECTIONS OR RIGID PIPING, DEPENDING ON PROVINCIALAND
LOCAL CODES, TOATTACH BURNER TO GAS SUPPLY. BE SURE TO USE PROPER SIZE GAS SUPPLY
LINE.. CAREFULLY CHECKALL CONNECTIONS FOR GAS LEAKS WITH SOAPAND WATER SOLUTION.
EACH INSTALLATION MUST CONFORM TOALL LOCAL, PROVINCIAL, AND NATIONAL CODES. REFER TO
THE NATIONAL FUEL GAS CODE, LOCAL ZONINGAND CODE AUTHORITIES FOR DETAILS ON
INSTALLATION REQUIREMENTS.
Page 1

WARNING
-DO NOT burnANY materials in this fireplace.
-All occupants of the home, especially children, should be alerted about the hazards of the high surface
temperature and the chance of severe burning or the possible ignition of clothing.
-Young children should be carefully supervised when they are in the same room as the appliance.
-Due to the high temperatures, the fireplace should be installed away from furniture and draperies and out of
traffic area.
-Nothing should ever be placed on or near the surface of the fireplace, including the top of the unit.
-Clothing or other flammable material should not be placed on or near the appliance.
-Make certain the control panel, burners, fans, and venting system are kept clean. Inspection of these systems
should be inspected annually by a qualified service technician.
-Any safety screen or guard removed for servicing the appliance must be replaced prior to operating the
appliance.
-The fireplace, under NO circumstances, should ever be modified.
-Do not operate the fireplace if damaged, or if the glass is cracked. Any repairs must be done by a certified
technician.
General Safety (Home Owner)
Fire Extinguisher: Every home should have at least one fire
extinguisher. An approved Class A-B-C extinguisher
should be mounted on the wall near an exit and close to
the application, but not so close that accessibility to the
extinguisher could be blocked by a fire. Your local Fire
Department can advise you concerning the most
appropriate location.
Smoke Detectors & Carbon Monoxide Detectors on each
floor of your home to ensure your safety. It should be
located away from the gas appliance and close to the
sleeping areas. Follow the detectors manufacturers
placement installation and maintenance instructions
Safety for the installer
-Wear gloves and safety glasses for protection.
-Exercise extreme caution when using ladders or
when on roof tops.
-Be aware of electrical wiring locations in walls
and ceilings.
-Use a back support for heavy lifting.
Vent safety
-Venting must be installed according to local
codes.
Electrical code
When installed, these appliances must be
electrically grounded in accordance with local
codes.
Page 2
Table of Contents:
Page 1: Pre-Start Up
Page 2: General Safety
Page 3: Specifications
Page 4: Framing & Clearances Louvered
Page 5: Framing & Clearances Clean Face
Page 6: Framing & Clearances for Santa Fe
Page 7: Venting
Page 8: Venting Continued
Page 9: Venting Continued
Page 10: Door Fitting
Page 11: Electrical
Page 12: Planning
Page 13: Fan Installation Kit
Page 14: Thermostat Installation
Page 15: Log Installation
Page 16: Log Installation Continued
Page 17: Parts List
Page 18: Lighting Instructions
Page 19: Final Checks
Page 20: Trouble Shooting
Page 21: Trouble Shooting Continued
Page 22: Maintenance

SPECIFICATIONS
Note: Always check appliance label for correct information.
MODEL: MB-36 Natural Gas Propane
Manifold Pressure 1.6-3.5in w.c. 6.0-10.0in w.c.
Min. Supply pressure for purpose 5.0in 11in w.c.
of input adjustment
Max Supply pressure 11in 13in
Orifice size 45 1.30mm
Nominal input rating 17,500 BTU/hr
High altitude (US) 0-2000ft / 0-610m
High altitude (Canada) 0-4500ft / 0-1370m
Primary Air Opening
Electrical Rating 115 volts 0.7amp 60hz
Heater Rated 72%
Steady State Efficiency 52.85% 59.87%
P.4.1 Annual Fireplace Efficiency 47.87% 49.44%
Circulating fan (optional) Variable Speed
Vent System Direct Vent
Log Set Ceramic Fiber
Glass Tempered
Louvers (optional) Black, plated
Clean Face Kit (optional) Black
Trim Kit (optional) Black, plated
Please Note: Only Trim Kits supplied by the manufacturer may be used in the installation of
this appliance.
Certification
The Model MB-36 is listed and certified for the installation in the U.S.A. and
Canada under the following standards:
ANSI Z21.88/CSA 2.33.
The installation must conform with local codes, or in the absence of local
codes, with the National Fuel Gas Code,
ANSI Z223.1 / NFPA 54 in the US, or the Natural Gas and Propane
Installation Code, CSA B149.1 in Canada.
Please contact CFHM if you have any questions regarding the certification
of this appliance.
LUXOR ZERO CLEARANCE FIREPLACE SPECIFICATIONS
MODEL WIDTH / HEIGHT / DEPTH / BACK WIDTH BTU
MB-36 36” 32” 14” 28” 17,500
Viewing area: 30” 19”
Page 3

Framing and Clearances For Louvered Fireplace
Note: Make sure that you allow for installation of any
wiring, such as the fan, remote control or wall switch
before applying finishing material.
The following diagram shows a typical framed installation.
All clearances must be adhered to. combustible material
such as timber must not be placed any closer to the
appliancethanthestand-offsallow.
Maintain required clearance around the vent pipe (1”
horizontal1”vertical).
Combustible material: Such as wood, compressed paper,
plant fibers, plastics or any material capable of igniting and
burning, whether flame proofed or not, plaster or un-
plastered.
Framing the enclosure
It is best to frame your
fireplace after it is
positioned and the system
is installed. Framing
dimensions are as
follows:
Model
MB-36 Depth 14” Height 32” Width 36” B. Width 28”
Note: This fireplace does not require a hearth
extension and may sit directly on combustible
materials.
Corner installation
Mantle clearances
Page 4
WARNING: No materials,
combustible or otherwise
shall occupy the space shown
surrounding unit.
*Unit to 3/4” trim is 8”
Inside framed size for termination:
-Luxor horizontal with flex: 10” x 10” inside
-Simpson DuraVent (P/N 984) 10” x 11”
Please note: Wall thimble (P/N 942) may be
required for installations in Canada.
55”
39½”
WH
D
Minimum Clearances to Combustibles
All clearances are determined when facing the fireplace front.
Clearances within recess:
Top: 3½”
Sides: 0”
Back: 1”
Floor: 0”
Recess Depth: 14”
3½”
Drywall
8”
¾” mantle
12” mantle
12”
8” mantle
10”
2”x 4”
1”
Side mantle pieces may come
down along the outside of the
fireplace, with no restrictions as
to how they may protrude out
from the unit.

Framing and Clearances For Clean Face Fireplace (no louvers)
Note: Make sure that you allow for installation of any wiring, such
as the fan, remote control or wall switch before applying finishing
material.
The following diagram shows a typical framed installation. All clearances
must be adhered to. combustible material such as timber must not be
placedanyclosertotheappliancethanthestand-offsallow.
Maintainrequiredclearancearoundtheventpipe(1”horizontal1”vertical).
Combustible material: Such as wood, compressed paper, plant fibers,
plastics or any material capable of igniting and burning, whether flame
proofedornot,plasterorun-plastered.
Framing the enclosure
It is best to frame your fireplace after it is positioned
and the system is installed. Framing dimensions are
as follows:
Model
MB-36 Depth 16” Height 32” Width 36” B. Width 28”
Note: The Fireplace does not require a hearth
extension and may sit directly on combustible
materials.
Corner installation
Page 5
Inside framed size for termination:
-Luxor horizontal with flex: 10” x 10” inside
-Simpson DuraVent (P/N 984) 10” x 11”
Please note: Wall thimble (P/N 942) may be
required for installations in Canada.
58½”
41¼”
WH
D
WARNING: No materials,
combustible or otherwise
shall occupy the space shown
surrounding unit.
Mantle clearances
3½”
Drywall
¾” mantle
12” mantle
2”x 4”
1”
4½”
Non combustible
*Unit to 3/4” trim is 8”
12”
8” mantle
10”
8”
Clean Face Kit
Please Note: The standoffs
provided with each MB-36 are
not required for installation
with the clean face kit.
Side mantle pieces may come
down along the outside of the
fireplace, with no restrictions as
to how they may protrude out
from the unit.

Framing and Clearances For Santa Fe Front (no louvers)
Note: Make sure that you allow for installation of any wiring, such
as the fan, remote control or wall switch before applying finishing
material.
The following diagram shows a typical framed installation. All clearances
must be adhered to. combustible material such as timber must not be
placedanyclosertotheappliancethanthestand-offsallow.
Maintainrequiredclearancearoundtheventpipe(1”horizontal1”vertical).
Combustible material: Such as wood, compressed paper, plant fibers,
plastics or any material capable of igniting and burning, whether flame
proofedornot,plasterorun-plastered.
Framing the enclosure
It is best to frame your fireplace after it is positioned
and the system is installed. Framing dimensions are
as follows:
Model
MB-36 Depth 16” Height 32” Width 36” B. Width 28”
Note: The Fireplace does not require a hearth
extension and may sit directly on combustible
materials.
Corner installation
Page 6
Inside framed size for termination:
-Luxor horizontal with flex: 10” x 10” inside
-Simpson DuraVent (P/N 984) 10” x 11”
Please note: Wall thimble (P/N 942) may be
required for installations in Canada.
58½”
41¼”
WH
D
WARNING: No materials,
combustible or otherwise
shall occupy the space shown
surrounding unit.
Mantle clearances
3½”
Drywall
¾” mantle
12” mantle
2”x 4”
1”
4½”
Non combustible
*Unit to 3/4” trim is 8”
12”
8” mantle
10”
8”
Santa Fe Kit
Please Note: The standoffs
provided with each MB-36 are
not required for installation
with the Santa Fe kit.
The unit may be finished with stucco or other non-
combustible materials right up to the edge of the
glass as shown.
Stucco
Side mantle pieces may come
down along the outside of the
fireplace, with no restrictions as
to how they may protrude out
from the unit.

Lip goes at the
top as shown.
4 self tapping screws
in pre-drilled holes.
Please note: standoffs
must be removed for
installation of clean
face kit. The CFK
then becomes the
standoffs.
Installation of Clean Face Kit continued
Flat piece sets in
place on tabs.
Lip goes at the
top as shown.
Bring finishing product
right down to the lip as
shown.
Overlap side so it is flush
with the opening as shown.
Please note: the custom doors we manufacture
for this unit fit inside the opening, so do not
bring finishing products beyond the opening.
Simply overlap all the metal as shown below to
ensure a nice square finish.
Page 7

Venting Identification
Page 8
Before unit installation, provisions for adequate combustion and
ventilation must be made.
Simpson Dura-Vent
*SD-0961 30 elbow (vertical)
*SD-0960 60° elbow (horizontal)
SD-1208 6” length of pipe
SD-1207 9” length of pipe
SD-1206 12” length of pipe
SD-1204 24” length of pipe
SD-1203 36” length of pipe
SD-1202 48” length of pip
SD-1211 Adjustable pipe length 11-145/8”
SD-1284 Horizontal square term cap
SD-1250 Vinyl siding standoff
SD-1245 45° elbow
SD-1290 90° elbow
SD-1249 Wall fire-stop
SD-1263 Ceiling fire-stop
SD-1243 Roof flashing 0/12 to 6/12 pitch
SD-1253 Storm collar
SD-1291 High wind vertical top
SD-1281 36” Snorkel
SD-1282 14” Fire-stop snorkel
SD-1288 Wall strap
*one is necessary to complete installation of Simpson Dura-Vent
°Flex
-Horizontal Termination only
provided by CFHM
-4” and 7” flex piping
WARNING: This gas appliance must not be connected to a chimney flue serving a separate solid-fuel burning appliance.
Please Note: Flex Pipe requirements
are UL,ULC rated comprises of 2 X
.005 wall thickness of type 3003
Aluminum or better. MB36 utilizes 7
inch and 4 inch diameters.

12’horizontal
Venting Maximum Runs
Page9
For horizontal termination,
you can use either Simpson
DuraVent or Flex with Luxor
Termination.
For Simpson DuraVent a
30° elbow is necessary for
vertical run.
O
For Simpson DuraVent a
60 elbow is necessary for
horizontal run.
2ft Min
2ft Min
2ft Min
Attention: Any venting configuration
that completes with a vertical
termination requires installation of CFHM
Part # MBR Restriction.
12’horizontal
32’vertical
Installation with Flex Venting.
16’horizontal
32’vertical
Installation with Simpson DuraVent
32”
32”
Attention: Any venting configuration
that completes with a vertical
termination requires installation of CFHM
Part # MBR Restriction.