LY International Electronics HS-3404 User manual

MOUNTING INFORMATION
MULTI-PURPOSE
FIXED / PENDANT
SPEAKER
45
SPECIFICATIONS
HANGING INFORMATION
When mounting the speaker to the wall, make sure the
proper screws / bolts are used.
Ceiling
Pole
Hanging Cable
Carabiner
Eye Bolt
Pendant Speaker
Make sure the speaker is properly secured to the ceiling /
building’s structure. please use the proper screws, bolts,
or anchors (not included). Failure to do so may cause the
speaker to become unsecured &cause potential damages/
injuries.
for 4''/5.25'' speaker
for 6.5'' speaker
MODEL
Woofer
Tweeter
RMS Power
Frequency Response
Nominal Impedance
Sensitivity(1M/1W)
Transformer
Product Dimension
4" PP Cone
0.75" Silk Dome
20W
120Hz-20kHz
8Ω
83dB
C70V: 1.25W-2.5W-5W-10W-NC & 8Ω,
C100V: 2.5W-5W-10W-20W-NC & 8Ω
138x138x190mm (5.4"x5.4"x7.5")
MODEL
Woofer
Tweeter
RMS Power
Frequency Response
Nominal Impedance
Sensitivity(1M/1W)
Transformer
5.25" PP Cone
1" Silk Dome
30W
110Hz-20kHz
Product Dimension 170x170x240mm (6.7"x6.7"x9.4")
8Ω
84dB
C70V: 1.87W-3.75W-7.5W-15W-NC & 8Ω,
C100V: 3.75W-7.5W-15W-30W-NC & 8Ω
MODEL
Woofer
Tweeter
RMS Power
Frequency Response
Nominal Impedance
Sensitivity(1M/1W)
Transformer
Product Dimension
8Ω
85dB
6.5" PP Cone
1" Silk Dome
40W
100Hz-20kHz
208x208x280mm (8.2"x8.2"x11")
C70V: 2.5W-5W-10W-20W-NC & 8Ω
C100V: 5W-10W-20W-40W-NC & 8Ω
HS-3404/HS-3504/HS-3604
OHS-3404
HS-3504
HS-3604
LY International Electronics Co., Ltd
http://www.lyintl.com

1 2 3
PACKING LIST SET UP AND OPERATIONSAFETY INSTRUCTIONS
1
2
3
4
5
6
7
USER
MANUAL
user manual
speaker
Please read the instructions carefully before installation and
use. Keep the manual safe for future reference.
Prior to installing the speakers into any ceiling or wall, check
the structure for weight bearing ability and avoid contact
with any wiring or plumbing that might be behind the surface
area. Installing on soft materials or in areas incapable of
supporting the speakers’ weight may cause personal injury
or damage to the speaker. When installing this series
speakers outside, choose areas such as the underside of
eaves to avoid strong direct sunlight which may affect the
color and life of the speaker enclosure.
When placing the speakers on a wall or shelf, it is
recommended that speakers be installed at the level of the
ear or slightly higher.
Damage to the woofer and tweeter may occur if the speaker
is dropped or hit - resulting in no sound or distorted sound.
Use only approved and certified wiring in your installation, do
not stretch or place the wire in contact with sharp objects.
Never overdrive your speakers to the point of distortion and
always reduce volume prior to switching input sources
(e.g.: FM to CD).
Turn off the power to the speaker when unused for long
periods of time.
To tilt the speaker, loosen the adjustment screw found on the
bracket. Tilt the speaker to the desired position and tighten
the screws securely.
This series speakers can be used as hanging ceiling, wall
mounted or as floor speakers. Model HS-3404/HS-3504 can
rotate 360 ° up and down while hanging or in wall mount
position. NOTE: HS-3604 is not recommended to rotate
after installation due to its weight.
8
9
Hanging Mount Accessories
Optional Wall Mount Accessories
top cover eye bolt & nut hanging cable
carabiner X2 screws X2
screws X4UV resistant cap
adjustable stand
(for 4''/5.25'' speaker) (for 6.5'' speaker)
buckle part
buckle part
1 2
+ -
-
+
-
+
1 2 3 4
+ + - -
1 2 3 4
+ + - -
1 2 3 4
+ + - -
-
+
-
+
1 2
+ -
1 2
+ -
For 4" Speakers (from power amplifier to next speaker)
For 5.25"/6.5" Speakers (from power amplifier to next speaker)
Connections (For Speakers with Transformer)
Ensure that the speaker is unplugged from the mains before making
any connections.
1Connect the wires from the amplifier (or the previous speaker)
to the supplied terminal block of the speaker, and ensure red wire
to “+” and black wire to “–“. Attach the top cover to the speaker.
2
Note: If mounting to the wall with the mounting bracket, mount
the bracket using the appropriate hardware and securely attach
to the wall.
Fasten the provided eye bolt to the top cover and speaker.
3
Route the speaker cable hanging from the ceiling area through
the top cover, and dress the cables to the wire rope using plastic
cable ties, strip the ends of the cables approximately 1/8" to
3/16" and, if the wire is stranded, twist the strands.
Fix the buckle part
for tangle-free cable.
(Available for purchase separately.)