MachPower WL-CPE5G24-059 User manual

WIRELESS CPE/AP 5G
OUTDOOR 450MBPS
WL-CPE5G24-059
USER MANUAL

REV.1216

3
Thanks
for choosed our product

4
INDEX
CHAPTER 1 Connection and Power Supply
1.1 Port Connection and power supply
CHAPTER 2 Login
CHAPTER 3 Quickly Configure CPE
3.1 Gateway Mode
3.2 WiFi Repeater&Station operation configuration
3.3 AP Mode
3.4 WISP
3.5 Advanced Settings
3.5.1 System Status
3.5.2 Operation Mode
3. 5. 3 5.8GHz Repeater
3. 5. 4 5.8G Wireless

5
3.5.5 Network Setting
3.5.6 Management
3.5.7 Upgrade Firmware
3.5.8 Share Internet&Obtain IP address automatically
CHAPTER 4 Trouble Shooting
CHAPTER 5 SMB Products

CPE
LAN PORT
PC
PoE LAN
PoE Adapter
6
CHAPTER 1
CONNECTION AND POWER SUPPLY
1.1 Port Connection & power supply
Instruction of different port
• Please use a power supply of 12V DC
adapter or 24V POE adapter, WAN /
LAN port is the PoE Port.
• The connection diagram of CPE and
PoE adapter
Pls make sure the CPE’s power supply
is normal and in correct connection
way, or the CPE will be damaged and
can’t reboot

• Reset
There are two ways to reset the CPE:
1. CPE Manage page: Click “Manage-
ment”, then “Save/Reload Settings”,
then click“Reset Settings”to finish the
CPE Reset
CHAPTER 2
LOGIN
1. Connect the CPE with computer
2. Configure the PC’s local connection
IP address as 192.168.1.X (X is num-
ber from 2 to 254), subnet mask is
255.255.255.0, follow next image
7

8
3. Input 192.168.1.1 into IE browser,
then pop up the login page, the default
login user name: Admin, Passwords:
admin, pls do following the next
image.
4. After login, then Device Status will
be showed
There are four operation mode showed
on this page:
Gateway mode, Repeater Mode, AP
Mode and WISP Mode;
And the default operation mode is
Wireless AP.

9
CHAPTER 3
QUICKLY CONFIGURE CPE
3.1 Gateway Mode
Click “Gateway Mode” under following
picture and choose the right WAN
access type, then input the right SSID,
Channel, key as like.

10
3.2 WiFi Repeater and Station opera-
tion configuration
A. Login the Web management page,
click “ Repeater Mode”, then “Scran
AP”

11
B. Select the AP’s SSID want to bridge,
take test-3200-5G for example, Select
AP
If your computer can’t pop up this
window, pls check your IE explorer and
see whether it is blocked already. And
if this CPE can’t scan any SSID, pls
check if there are 5G wireless signal.

12
C. Input the AP’s key, and apply
changes, then the outdoor CPE in wifi
repeater.

13
3.3 AP Mode
Plug and Play to transmit wireless
signal for wireless end users form
wired networking. In this part, user
can mark the AP’s location and name
for easy problem checking. Then can
change SSID, Key, Channel as request.

14
3.4 WISP
In this operation mode, user should
confirm the WAN access type at first,
then set the SSID, key, Channel as
request.

15
3.5 Advanced Settings
3.5.1 System Status
Click “ Advance Settings”, will show
system status, such as firmware ver-
sion, build time, System uptime.
Click 5.8GHz Wireless Status, will
show CPE’s WLAN Status, Signal
Strength, SSID.

16
If want to check LAN status, pls check
following picture
3.5.2 Operation Mode
Set operation mode manually, choose
the right operation mode, then apply
changes. The function of this part will
be same as Quick Setup step

17
3.5.3 5.8GHz Repeater
In this part, main function is wifi repe-
ater, bridge exist wireless Ap, then set
security as you like.
3.5.4 5.8G Wireless
In this part, users can managed
the CPE’s SSID, password, channel,
bandwidth, security method, firewall,
virtual AP.

18
How to set 5.8G Virtual AP, pls take
1,2,3,4,5 steps
How to allow / deny the end user list to
access into this CPE.

19
3.5.5 Network Setting
LAN Interface Setup mainly showed
as follow:

20
3.5.6 Management
In this part, user can set Time zone,
show Log info, upgrade firmware,
change login user name and pas-
sword;
3.5.7 Upgrade Firmware
Pls click Upgrade Firmware, then
browse and choose the firmware
should upgrade, then click upgrade to
upgrade the firmware.
After finish firmware upgrade, pls
click Save/Reload Settings, then reset
settings to default.
After that, the firmware upgrade is