Macrom M-TVT300D User manual

ALDINET Spa
Viale C: COlombo, 8
20090 Trezzano s. Naviglio (MI)
IYALY
M–TVT300D
M–TVT300D
English

Use Dibcom dib 7070m high performance mobile chip.
Two T-NIM structure performs good diversity reception with
signal gain around 3-6dB
Speed over 230km/h min (at 8k,64QAM,CR2/3,GI1/8,474MHz)
High doppler effect correction
Provide antenna power supply function for pair use with mobile
active antenna
Over 1000 channels TV & radio Programmable
Channel list editing
Favorite channel list editing
PIG (Picture in Graphic) support
Electronic program guide (EPG) or on screen channel information
software upgrade
OSD teletext (DVB ETS 300 706) and subtitle function support
(EU model)
VBI teletext support (EU model)
Fast scan for high speed driving and cross different area
Feature:
1

Tuner:
RF Input
Input Impedance
Signal Level
Connector Type
Channel Band Width
FEC
Demodulation
Standard
Constellation
Guard Interval
COFDM Carrier Mode
Video Decoder
Standard
Transport Stream
Video Aspect Ratio
Video System
Video Output
Video Resolution
UHF: 470 MHz ~ 862MHz
VHF: 174 MHz ~ 230 MHz
75
-78dBm ~ -20dBm
F Terminal
6M/7M/8M
DVB-T EN300 744
QPSK, 16QAM, 64QAM
1/32,1/16,1/8,1/4
1/2,2/3,3/4,5/6,7/8
2K And 8k Non Hierarchical/Hierarchical
MPEG-2 MP@HL
ISO/IEC 13818-1 MPEG-2
4:3 /16:9
PAL/NTSC
1 ± 0.3Vpp
720*576@25fps or 720*480@30fps
Technical Specification
2

Audio Decoder
Standard ISO/IEC 11172-3
Audio Decoder MPEG-1 audio Layer II
Audio Channel R/L/ST
Audio Output 1Vpp 47Kohm Adjustable With E Volume
General:
MPEGⅡ
Chip
SUNPLUS SPHE1002AT With 32bit RISC
ARC CPU 121.5 MHz
Flash Memory 8Mega bit
SDRAM 64 Mega bit
Operating Temperature -10 ℃ ~ +
Storage Temperature: -40 ℃
50 ℃
65℃
~ +
Power Supply DC 12V 320 mA
Power Consumption Running: 3.8W Max , Standby :2W Max
V
3

Remote Control Unit(RCU)
- POWER:
Switch the receiver between stand-by
& on modes
- Mute :
Mute the audio output
- Numeric Keys(0~9):
For direct entry of channel number or
input of alphanumeric characters
- MENU:
Access the main menu
- CANCEL:
To return to previous status or exit
- CH+/- ( / ):
Change channels sequentially up or
down in viewing mode and move to the
next higher or lower item in the menu
- CH LIST:
A list will enter the channel in viewing
mode
- VOL+/-( / ):
Alter the Audio output level up or down
in viewing mode or move to the left or
right item in the menu
- OK:
Select an item or confirm a choice.
- EPG (Electronic Program Guide):
Call up the EPG function
- INFO:
Display information on viewed channel
-Fast scan:
Searching all channel quickly
OK
POWER
EPG DISP LAY
CH LIST
MUTE
4

1.BAS IC FUNC TIONS
1.1 En ter into system and power on-off
Enter into DVB system
It wi ll enter DVB mod e as soon as system power on.
It wi ll continue to play the last est program before previous power off if the
database having and TV. or RADI O program.
Power on
Whe n it is“standby”mod e,press“power”to power on.
Power off
Whe n it is running, press“ powe r” will enter into“standby”mod e.
1.2 Volume adjustmen t and Mut e
Press “VOL +/-”to adjust volume when system is in normal playing mod e: and it will
show volume bar on the imag e.
Press“MUTE ”to enter into the mod e when normal ly playing and repress“MUTE ”to
back the normal state.
1.3 St ation switch
Press “CH+ /-”to switch to the previous or next program.
Press“OK” to switch to the speediness program list, press “VOL +/-”to select
different program class; press“ CH+ /-” to select program
Press“OK” to affirm program Se lection, press“ EXI T”to hide men u
1.Press numbe r keys to input program numbe r.
2.If there are some favorite programs that been set up, just press “FAV” to enter
into the favorite program list:
Press“CH+ /-” to select favorite program, Press“OK” affirm the selection, press
“EXI T” to hide men u.
1.4 Di splay informat ion of programs
Press key“INFO” to show the informat ion of current programs when it is in normal
playing state. Pr ess again to show mor e detail informat ion.
1.5 Pr ogram return
Press key“RECA LL”under state of full-screen to return to the previous program
played.
1.6 Audio language swi tch and L/R channel switch
1.Press “AUDI O”key to switch the language of current programs and switch amon g
“stereo”→“Left”→“right”(stereo→left channel→ right channel)
2.Press “VOL +/ -”to switch amon g “stereo” “left” “right”(stereo→left
channel→right channel),press “CH+ /-”to swi tch the language of sound.
5

3.Press “OK”key confirm the selection and return to full-screen play mode, press
“EXIT” to return to full -screen play mode but not save the setting.
1.7 Electronic programs guide(EPG)
1.You can press key“EPG”on the remote controller to enter into the EPG page the
bottom Line shows hint information for keys, corresponding to the colors on the
remote controller: RED, GREEN, YELLOW, BLUE;
(8).Press“VOL+/-”to switch between Tab 4 and Tab 5 ;
2. Press“GREEN”key to enter into Weekly Mode to display the programs and program
information in different time ranges of the currently program list within one week, as
shown in Figure 3.7:
(1).Press PGUP&PGDW key to switch between Sunday—Saturday in Tab 3;
(2).Press CH+/- key to move upward and downward to switch between the different
programs in Tab 5;
(3).Press VOL+/- key to choose to view the program information in different time
ranges in Tab 6.
3. When the cursor stops on Tab 5 in Figure 3.6 Tab 6 in Figure 3.7, press the yellow
key to choose the detailed information corresponding to the current program, as
shown in Figure 3.8:
Figure 3.7 Weekly Mode
Figure 3.8 Extended Mode
6

4. When the cursor stops in Tab 5 of Figure 3.6 and Tab 3.7, press the blue key to
enter Wake up Timer menu to book programs, as shown in Figure 3.9:
5. Press“EXIT”to exit from EPG.
1.8 Teletext
1.If you want to teletext, please press“TTX”on the remote controller to
enter into the teletext page. As shown in the figure below:
2.Input three digits to go to corresponding page you want;
3.Press“CH+” to go to the previous page, while press“CH-”to go to the
next page;
4.Press“VOL-”to back for 100 pages, while press“VOL+”to advance for
100 pages.
5.Press“TTX”or“EXIT”to exit from teletext.
Figure 3.9 Wake up timer
Figure 3.10 Teletext page
7

1.Subtitle is defaulted to be off; to see the capitation information, press the SUB-
TITLE key on the remote controller to enter the Subtitle menu of the current programs.
2.Press VOL+/- key to choose whether to open Subtitle, press CH+/- key move
upward and downward to choose language.
1.9 Subtitle
2.DIGITAL TV
In the main menu of the system, under Digital TV, there are such as options as auto
TV search or broad cast programs, program management, system set up, software
update and software version information view etc.
In Main Menu, press CH+/- key to choose Digital TV option and then Press OK key
once to enter Digital TV menu.
2.1 INSTALLATION
There are three kinds of Installation mode as follow:
1. Area Search: searching programs by scan area;
2. Manual Search
3. Auto Search
You can enter into parameter“installation page”via input password digital (default
password is“0000”)
2.1.1 Area Search
Area search is a kind of intelligent and convenient mode of programs searching,
which covers programs of all frequency points of target countries and regions.
At present, this system covers many targets countries and regions including:
Germany/ England/ Italy/ France/ Spain/ Holland/ Taiwan/China/ Norway/ /
Finland;
The default country(region) of system is Germany(you can select target countries you
want under system setting scan Area).
1. You can move the cursor to“area search”via press“CH+/-” key under“installation
menu” ,then press“enter”to enter into area searching page.
2. After entering into area search page, system will scan all programs one under
frequency points of current countries or regions selected automatically.
3.During scanning, press”EXIT” key to stop and exit scanning.
4. If any program is detected and scanning process is finished,system will
exit the scanning page and to play them in window automatically.
2.1.2 Manual Search
If you understand much about digital TV and know the frequency of the program
or if you want to scan the program at any frequency required, you can select manual
scanning, which can save your much time.
Swedish
8

1.You can move the cursor to“area search” via press“CH+/-” key under “installation
menu” ,then press“enter” to enter into area searching page.
2.Prior manual scanning, you need to configure relevant parameters including:
(1).Freq(KHz): the default frequency is 474000KHz, you can input relevant digital to
modify it.;
(2).Band Width: the default value of bandwidth is 8 MHz. while you can set it to 6 MHz,
7 MHz, 8 Mhz.;
3.Press“OK”key after configuration of start manual scan.
4.If any program is detected and the scanning process is finished, system will exit the
scanning page and save the program, at the same time return to the“installation menu”
and to play them automatically. As shown in the figure below:
2.1.3 Auto Search
You can search the programs of any channel.
1.You can move the cursor to“area search” to enter into area searching page, As shown
in figure below:
2.Prior to auto scanning, you need to configure relevant parameters including:
(1).Start Freq(KHz):the default frequency is 474000KHz, you can input relevant digital
to modify it.;
(2).End Freq(KHz):the default frequency is 474000KHz. While you can input relevant
digital to modify it;
(3).Band Width: the default value of bandwidth is 8 MHz. while you can set it to 6 MHz,
7 MHz, 8MHz .;
3.Press“OK”key after configuration of parameters to start manual scan.
4.If any program is detected and the scanning process is finished, system will exit the
scanning page and save the program, at the same time return to the “installation
menu” and to play them automatically. As shown in the figure below.
2.2 CHANNEL MANAGER
System offer an efficient function of channel management such as channel deleting,
marking, moving, locking, sorting and grouping.
There are two independent pages for channel management, TV and RADIO.
You can enter the page via“digital TV channel manager” as shown in the figure below:
Figure 4.7 auto search menu
9