Magnetic Autocontrol MHTM FlowMotion mSwing User manual

Operating Instructions
Swing door
MHTM™ FlowMotion®
mSwing
Doc.ID: 5817,0032EN
Version 00
mSwing
mSwing

2
mSwing
MAGNETIC AUTOCONTROL GMBH
Grienmatt 20
D-79650 Schopfheim
Germany
Phone [phone]
Fax [phone]
[email protected]
www.magnetic-access.com

3
mSwing
Contents
Contents
1 Notices on the document 7
1.1 Purpose and contents of this operating instructions 7
1.2 Read and store the operating instructions 7
1.3 Non-compliance with the operating instructions 8
1.4 Symbols and illustrations used in these operating instructions 8
1.4.1 Warning notices and notices 8
2 Safety 10
2.1 Intended use 10
2.2 Changes and modifications 10
2.3 Target groups 11
2.3.1 Operator and his responsibilities 11
2.3.2 Personnel - activities and qualifications 12
2.4 Personal protective equipment 13
2.5 Symbols on the device 14
2.6 For your safety 15
2.7 To protect the environment 16
2.8 Emergency opening of the pedestrian gate 16
3 Technical data 17
3.1 Dimensions and design 17
3.1.1 mSwing with wing FMSW_MG 17
3.1.2 mSwing with bracket FMSW_MU 19
3.2 Clearances 20
3.3 Swivel range and required mounting width 21
3.3.1 mSwing with wing FMSW_MG 21
3.3.2 mSwing with bracket FMSW_MU 22
3.4 Electrical connection 23
3.5 Operating conditions 23
3.6 Emissions 23
3.7 Control unit MGC 24

4
mSwing
Contents
4 Design and function 25
4.1 Design of the mSwing with wing FMSW_MG 25
4.2 Design of the mSwing with bracket FMSW_MU 26
4.3 Function 27
4.4 Definition of "left" and "right" 28
5 Receipt of goods, transport and storage 29
5.1 Goods receiving department 29
5.2 Safety during transport 29
5.3 Transport 30
5.4 Storage 31
6 Unpacking, scope of delivery and identification 32
6.1 Unpacking 32
6.2 Scope of delivery 33
6.3 Identification 34
6.3.1 Type plate 34
7 Installation and assembly 35
7.1 Safety during installation and assembly 35
7.2 Mounting variants 36
7.3 Required steps 37
7.4 Setting up foundation and placing empty conduits 38
7.4.1 Requirements foundation 38
7.4.2 Requirements empty conduits 38
7.4.3 Thread the lines into the floor ring
via cable screw connections 39
7.4.4 Setting up foundation and placing empty conduits 40
7.4.5 Foundation and empty conduit plan
and reinforcement 40
7.5 Set mSwing position 41
7.5.1 Determining the orientation of the blocking element 41
7.6 Preparing the mSwing for mounting 43
7.7 Mounting the floor plate 45
7.7.1 Mounting variant "Direct mounting" 45
7.7.2 Mounting variant "Mount base plate" 49
7.7.3 Mounting variant "Glue base plate" 56
7.7.4 Mounting variant "Glue floor plate" 60
7.7.5 Mounting variant "plates or interlocking stones" 65

5
mSwing
Contents
7.8 Assembly of the mSwing 67
7.9 Adjusting the end stops 71
7.9.1 Explanations of mechanical end stops 71
7.9.2 Adjusting the end stops 71
7.9.3 Factory setting and example for another setting 72
7.9.4 Adjusting the fixed end stops (gross adjustment) 73
7.9.5 Adjusting the following end stops
(precise adjustment) 74
7.10 Mounting and dismounting the blocking element 75
7.10.1 Mounting the blocking element "Wings" 75
7.10.2 Dismounting the blocking element "Wings" 77
7.10.3 Mounting the blocking element "Bracket" 78
7.10.4 Dismounting the blocking element "Bracket" 81
7.11 Opening and closing the housing 82
7.12 Checking the assembly 82
8 Electrical connection 83
8.1 Safety during electrical connection 83
8.2 Installing electrical protective devices 84
8.3 Connecting the mains cable 85
8.4 Connecting customer control lines 86
8.4.1 Connecting emergency opening contacts 87
8.5 Checking the electrical connections 87
9 Commissioning 88
9.1 Safety during commissioning 88
9.2 Putting the pedestrian gate into operation 88
9.3 Switching the pedestrian gate on and off 88
9.4 Parameterising the pedestrian gate 89
10 Test book 89
11 Operation 90
12 Cleaning and maintenance 90
12.1 Cleaning the pedestrian gate 90
12.2 Maintenance schedule 91
13 Corrective action 91

6
mSwing
14 Spare parts and repair 92
15 Customer service 92
16 Decommissioning 93
16.1 Safety during decommissioning 93
16.2 Take the pedestrian gate out of operation 93
17 Disassembly and disposal 94
17.1 Safety during disassembly and disposal 94
17.2 Dismantling and disposing of the pedestrian gate 94
18 EU-Declaration of Conformity 95

7
mSwing
Notices on the document
1 Notices on the document
1.1 Purpose and contents of this operating instructions
These operating instructions provide all the information required for the
product in the various phases of its life cycle.
These operating instructions contains the following information: Assembly and
function, transport and storage, unpacking and delivery, installation and
assembly, electrical connection, commissioning, operation, cleaning and
maintenance, decommissioning, dismantling and disposal.
IMPORTANT!
For parameterisation see separate document "Description of
MGC control unit for mSwing (Doc.ID: 5817,0031)".
1.2 Read and store the operating instructions
Pre-requisite for safe working is the observance of all specified safety notes,
warning notes and instructions. In addition, the local accident prevention
regulations, general safety regulations and local environmental regulations
applicable to the area of application of the product must be observed.
Carefully read these operating instructions before starting any work! The
operating instructions are a product component and must be kept in direct
proximity of the product, well accessible to the personnel at all times.
If the product is passed on to third parties, please also provide these operating
instructions.

8
mSwing
Notices on the document
1.3 Non-compliance with the operating instructions
Magnetic declines all liability for personal injury and material damage caused
by not observing the operating instructions.
This applies in particular to damage caused by:
› Non-intended use
› Use of non-qualified personnel
› Use of non-approved components
› Unauthorised modifications
› Inappropriate assembly and installation
› Improper operation
› Defective or unperformed maintenance and repairs
› Use of non-approved spare parts
› Operation of a faulty product
1.4 Symbols and illustrations used in these operating instructions
1.4.1 Warning notices and notices
Warning notes are characterised by pictograms in these operating instructions.
A warning note starts with a signal word that expresses the extent of the
hazard.
It is absolutely essential to observe the warning notes and to proceed with
caution in order to prevent accidents as well as bodily injuries and property
damage.
Warning Notes
DANGER
The signal word DANGER points to an immediately dangerous
situation, which leads to death or severe injuries if it is not
avoided.
WARNING
The signal word WARNING points to a potentially dangerous
situation, which can lead to death or severe injuries if it is not
avoided.

9
mSwing
Notices on the document
CAUTION
The signal word CAUTION points to a potentially dangerous
situation, which can lead to minor injuries if it is not avoided.
NOTICE
The signal word NOTICE points to a potentially harmful situation,
which leads to property damage if it is not avoided.
Notes and recommendations
IMPORTANT!
The signal word IMPORTANT highlights useful notes and
recommendations as well as information for an efficient and
trouble-free operation.

10
mSwing
Safety
2 Safety
2.1 Intended use
The Magnetic swing door mSwing is designed for the controlled passage of
persons who wish to enter or leave a restricted area. The swing door is also
suitable for persons who cannot pass through other types of pedestrian gates
such as turnstiles safely, quickly or without assistance. Such persons include,
for example, small children, elderly people or people with disabilities.
The swing door can be used as a supplement to pedestrian gates such as the
turnstile.
Children under 14 years of age may only pass through the swing door under
the supervision of an adult.
The swing door may only be mounted on non-flammable floors.
The swing door may only be operated within the temperature range indicated
on the type plate.
Misapplications
Any other or further use is considered improper use. Magnetic is not liable for
any resulting personal injury or damage to property.
For example, the following applications are considered to be contrary to
regulations:
› Mounting the swing door on a flammable floor.
2.2 Changes and modifications
Changes or modifications to the product, attachments or components may
result in unforeseen hazards. Before making any technical changes or
modifications to the product of any of the components, written permission
must be obtained from Magnetic.