Magtek DynaProx User manual

Right and Left Side
The sides are smooth with clear denition between the reader and the stand
with no extraneous wires other than the USB wire that comes out of the back of
the reader.
Device and Stand back
Cable Channel: Allows the cable to
be channeled out the back of the stand
body.
Bottom of Device
Bottom PN 10000008309
Soft elastomer bottom cover over steel ballast weight is on the bottom of the
device stand. There are 4 screw insets.
Two (2) screws attach the baseplate
to the stand.
There is an EMC regulatory label with
certication logos and certication ID
numbers, MagTek logo, and name as
depicted here.
Two (2) insets are to attach the stand
to a counter.
Form Factor Stand Body
The body of the stand is angled for
better ergonomics. Check the overall
form factor for signs of attempted
entry. Made from molded black
plastic with matching black lens on
the face. The form factor is hard
plastic. The seam between the top
and underside shell is clearly dened
with a tight t. There are no additional
electronics or wires. Any breaks in
the plastic, scuffs, or damage could
be signs of physical tampering and
should be reported.
Front and Top of Device
The front side and top of the reader
are smooth with no extraneous wires.
There is clear denition with a tight t
between the reader and the stand.
DynaProx BCR Top and Front
Overview
DynaProx and DynaProx BCR in stand (referred to as “Device” hereafter) deliver
the next generation in contactless EMV and near eld communication (NFC)
technology and can be purchased with a countertop, angled stand for stable
acceptance at the counter top. The purpose of this document is to perform a
device inspection and understand how to access the isolated reader.
Major Components
DynaProx and DynaProx BCR Stand
Device Inspection
Device Inspection
Assembled Inspection
MagTek
® Inc., 1710 Apollo Court, Seal Beach CA 90740 | p 562-546-6400 | support 651-415-6800 | f 562-546-6301 | www.magtek.com
DynaProx (shown here) Major Components - Assembled to Stand
LEDs
Four LEDs above the contactless
landing zone provide signals to the
user. See installation and operation
manual for complete LED signaling:
https://www.magtek.com/content/
documentationles/d998200490.pdf
Contactless Landing Zone
The contactless zone is on the top of
the device. BCR models have a lens
for the barcode camera.
DynaProx BCR Models ONLY
Barcode (BCR) models have a
camera and QR Code icon on the top.
DynaProx Only Models
Models without barcode reader are
identical, but do not have a camera
lens nor QR code printed on the top.
DynaProx and DynaProx BCR DynaProx and DynaProx BCR
in Stand
Dimensions 2.09 in. x 2.52 in. x .72 in.
(53mm x 64mm x18.5mm)
2.17 x 2.64 x 2.09”
(55 x 67 x 53mm)
Weight DynaProx = 2.0 oz. (56g)
DynaProx BCR = 2.0 oz. (58g)
DynaProx: 6.7 oz. (190g)
DynaProx BCR: 6.8 oz. (192g)
Look for any added components, size, or weight. Check for signs of cutting,
tapping, and bending.
Device Right Side Device Left Side
Device Back Side
Device Bottom Side
DynaProx Top and Front

Accessing the Reader
Remove from Counter
In order to access the reader from
the device stand you may need
to unscrew it from the counter.
Unscrew the two screws attaching the
baseplate of the stand to the counter.
Remove Base Plate from Stand
Unscrew the two set screws from the
base plate.
Remove USB-C Cable
Unplug the USB-C cable from the
back of the device, release the cable
from pinch t opening, and remove
from the integral cable hooks.
Remove 4 Set Screws
Unscrew the 4 screws that attach the
stand to the reader.
Underside of Device
Form Factor: of DynaProx and
DynaProx BCR are the same smooth
form factor with 4 threaded screw
holes, a USB-C receptacle, RS-232
receptacle, and product label.
Product Label: located on the
underside of the device. The Serial
Number, Rev, Date, Part number
(PN), and Hardware PN (HW) are
listed. Compare hardware ID to PCI
website for validation.
USB-C Connection: Connected
directly to the correct host USB port.
Imprints: in the plastic form factor
of certication logos and patent
information are listed.
RS-232 Connection: Connected
directly to the correct host port.
EMV® is a registered trademark in the U.S. and other countries and an unregistered trademark elsewhere. The EMV trademark is owned by EMVCo, LLC. The Contactless Indicator mark, consisting of four graduating arcs, is a trademark owned by and used with permission of EMVCo, LLC.
Registered to ISO 9001:2015 © Copyright 2022 MagTek, Inc. PN D998200542 rev. 20 7/22
MagTek
® Inc., 1710 Apollo Court, Seal Beach CA 90740 | p 562-546-6400 | support 651-415-6800 | f 562-546-6301 | www.magtek.com
D
C
B
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
A
SHEET 1 OF 1
DESIGNED BY
DO NOT SCALE DRAWING
DRAWN BY
TOLERANCE:
TITLE:
B
SIZE
PROPRIETARY AND CONFIDENTIAL
FINISH:
4.00 x 2.8265”
DWG REV :
CHECKED BY:
DATE
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MAGTEK. ANY REPRODUCTION IN PART
OR AS A WHOLE WITHOUT THE WRITTEN
PERMISSION OF MAGTEK IS PROHIBITED.
SCALE: 1:1
MUST BE ROHS COMPLIANT, SEE
EUROPEAN DIRECTIVE 2002/95/EC
DIM UNITS:
DWG NO.
MATERIAL:
PART NO.
1/10/2022
R.Robinson
R.Robinson
DynaProx & DynaProx BCR
EMV and NFC Contactless
DynaProx STORAGE NOTICE
TEMPERATURE: -30°C to +85°C (-22°F to 185°F)
HUMIDITY: 90% RH non-condensing
DynaProx BCR STORAGE NOTICE
TEMPERATURE: -40°C to +70°C (-40°F to 158°F)
HUMIDITY: 5 - 95% non-condensing
See product label for part number and description.
In-house Zebra label
PN 99600120
LABEL, STORAGE NOTICE, DYNAPROX
AND DYNAPROX BCR
1000008550
D100006015
B0
DynaProx and DynaProx BCR Stand | Device Inspection
Include the following for your device inspection audit:
• Be certain to have a list of the devices and include the details listed on the
product label.
• It may be helpful to take photos of the top, back, and side of each device.
Be certain to check device part numbers, serial numbers and IDs and check
physical connections. Use the chart below as a checklist to inspect the device
for signs of tampering.
Are there signs of tampering: Signs of tampering
Site Inspection YES NO
Form Factor - check overall form factor
Top
Contactless Landing Zone
LEDs
Barcode Reader Camera
Front, Left, and Right Sides
Plastic Shell
Form Factor
Cables
USB-C Cable
Bottom and Back
Form Factor
Cable Connection
Screw Sets
User should report all signs of tampering as per standard protocol.
NOTICE: If there is forced entry, the security switches built into the electronics
will be tampered. If they are tampered the sensitive data such as encryption
keys and certicates are cleared as part of security measures mandated by
PCI and the device will not be available to make transactions. If the device has
detected a tamper, DynaFlex Products cannot be repaired in the eld. Follow
RMA procedures. Devices must be returned to the factory for repair.
PCI DEVICE VALIDATION
To check for PCI Validation check the Hardware and Firmware ID. Hardware ID
is printed on the label. The firmware ID is accessible via a host command and is
displayed. Go to the PCI compliance web page and search for MagTek, and find
the product name, DynaFlex. Compare the Hardware ID and Firmware ID:
https://www.pcisecuritystandards.org/assessors_and_solutions/pin_transaction_devices
Device Inspection
Access Inspection - Views from Stand Bottom
Full Assembly
Diagram shows assembly pieces.
• 2-set screws
• Base plate
• 4 mounting screws
• Angled stand and cable
• DynaProx product