manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Majella
  6. •
  7. Amplifier
  8. •
  9. Majella VVCA User manual

Majella VVCA User manual

VVCA DIY MANUAL
Version 1.0
All manuals and user guides at all-guides.com
all-guides.com
VVCA Velocity Voltage Controlled Amplifier
DIY Manual
©2018 Majella Audio
2
INTRODUCTION
1. The VVCA
The VVCA kit is a small DIY kit. This kit is
suitable for DIY’ers who have their basic
soldering skills under control. The kit is
designed to be as easy as possible.
2. Requirements
The Kit contains the PCB, Panel and all
electrical components to finish the module.
You will need (as a bear minimum): basic
soldering tools and a Digital multimeter to
finish this module.
Required tools:
•Soldering iron/station
•Soldering tin
•Wire cutter
•Multimeter
•Nut driver (plier, at own risk )
3. Bill of materials (BOM)
To start, it is good practice to check if the kit
is complete. We double check the kitbags,
but we are human (tududududuuuhduuh)
after all.
All manuals and user guides at all-guides.com
VVCA Velocity Voltage Controlled Amplifier
DIY Manual
©2018 Majella Audio
3
22R Resistors (2x)
First we start with the 22R restistors. There
are two of them (R49, R50). They are placed
on the yellow markings in the figure 1.
Figure 1: 22R resistor placement
(YELLOW)
All manuals and user guides at all-guides.com
VVCA Velocity Voltage Controlled Amplifier
DIY Manual
©2018 Majella Audio
4
1K Resistors (7x)
Now that the 22R resistors are soldered we
can go on with the 1K resistors.
There are 7 resistors with a 1K value (R2, R12,
R14, R16, R22, R25, R32).
Their placement is shown in figure 2. They
are marked yellow. The blue resistors
represent the already soldered resistors:
Figure 2: 1K resistor placement.
(YELLOW)
All manuals and user guides at all-guides.com
VVCA Velocity Voltage Controlled Amplifier
DIY Manual
©2018 Majella Audio
5
10K Resistors (16x)
The next resistors to solder are the 10K
resistors. There are 16 of them that need to
be soldered (R4, R5, R6, R7, R13, R15, R18,
R19, R23, R24, R27, R28, R33, R34, R37, R38).
Figure 3: 10K resistor Placement
(YELLOW)
All manuals and user guides at all-guides.com
VVCA Velocity Voltage Controlled Amplifier
DIY Manual
©2018 Majella Audio
6
100K Resistors (8x)
Now we are going to do the 100K resistors.
There are 8 of them. (R3, R8, R17, R20, R26,
R29, R36, R39) Figure 4 shows their position
(yellow) on the PCB. Lets go champ!
Figure 4: 100K resistor placement
(YELLOW)
All manuals and user guides at all-guides.com
all-guides.com
VVCA Velocity Voltage Controlled Amplifier
DIY Manual
©2018 Majella Audio
7
220K Resistors (4x)
You should now be getting tired of
soldering resistors, but we are almost there!
Just four of these 220K resistors. (R1, R10,
R11, R31). They are yellow marked in figure 5.
Figure 5: 220K resistor placement
(YELLOW).
All manuals and user guides at all-guides.com
VVCA Velocity Voltage Controlled Amplifier
DIY Manual
©2018 Majella Audio
8
330K Resistors (4x)
The last 4 resistors! These are gonna be the
330K (R9, R21, R30, R40). Figure 6 shows
where they need to be placed.
Figure 6: 330K resistor placement
(YELLOW)
All manuals and user guides at all-guides.com
VVCA Velocity Voltage Controlled Amplifier
DIY Manual
©2018 Majella Audio
9
IC sockets 16 pin (2x)
For the LM13700’s we need to solder 2 IC
sockets. There are 2 IC sockets with 16 pins
on the PCB. Check the notch for
correct orientation!
Figure 7: 16 pin IC socket
placement (YELLOW)
All manuals and user guides at all-guides.com
VVCA Velocity Voltage Controlled Amplifier
DIY Manual
©2018 Majella Audio
10
IC sockets 14 pin (1x)
Now we need to solder the 14 pin IC socket
for the TL074 opamp. Check the notch
for correct orientation!
Figure 8: 14 pin IC socket
placement (YELLOW)
All manuals and user guides at all-guides.com
VVCA Velocity Voltage Controlled Amplifier
DIY Manual
©2018 Majella Audio
11
100nF capacitors (6x)
The are 6 capacitors on this board. Their
placement is marked yellow.
Figure 9: 100nF capacitors
placement (YELLOW)
All manuals and user guides at all-guides.com
all-guides.com
VVCA Velocity Voltage Controlled Amplifier
DIY Manual
©2018 Majella Audio
12
NPN transistors 2N3906 (4x)
The are 4 yellow marked PNP transistors on
the PCB. We now need to solder these. Do
not solder these the other way around!!
Check the belly for the orientation (figure
10).
Figure 10: 2N3906 Transistor
placement (YELLOW)
All manuals and user guides at all-guides.com
VVCA Velocity Voltage Controlled Amplifier
DIY Manual
©2018 Majella Audio
13
Power connector (1x)
To connect this module to your eurorack
system we will need to solder a 16 pin IDC
connector. Notice the orientation of the
connector (figure 11)!
Figure 11: Power connector
placement (YELLOW)
All manuals and user guides at all-guides.com
VVCA Velocity Voltage Controlled Amplifier
DIY Manual
©2018 Majella Audio
14
3.5 mm minijack connectors (8x)
Solder the 8 minijack connectors on the
PCB. We use these so you can include the
VVCA in your patch cable spaghetti! The
placement of the jacks is marked yellow in
firure 12.
Figure 12: 3.5 mm jack placement
(YELLOW)
All manuals and user guides at all-guides.com
VVCA Velocity Voltage Controlled Amplifier
DIY Manual
©2018 Majella Audio
15
22uF Capacitors (3x)
Almost done! We need to solder 3
electrolytic capacitors on the PCB. See
figure 12 for their placement. Note their
orientation, They will explode if not
correctly placed, no joke!!
The positive (+) side can be recognized by
the longer leg. The negative side (-) is
marked by a yellow/gold strip with the –
sign on it. The negative side is marked
purple in figure 12.
Figure 12: 22uF capacitors
placement (YELLOW)
All manuals and user guides at all-guides.com
VVCA Velocity Voltage Controlled Amplifier
DIY Manual
©2018 Majella Audio
16
IC placement
You can turn off your soldering iron! You will
only need to place the IC’s in their sockets!
Note the orientation of the IC’s!.
PCB is done!
Figure 12: IC placement
All manuals and user guides at all-guides.com
all-guides.com
VVCA Velocity Voltage Controlled Amplifier
DIY Manual
©2018 Majella Audio
17
Final check + panel
First check if the IC’s and the 22uF
capacitors are orientated correctly.
Now place the panel on to the jack
connectors and put on the Hex nuts, DONE!
All manuals and user guides at all-guides.com
VVCA Velocity Voltage Controlled Amplifier
DIY Manual
©2018 Majella Audio
18
Bill$of$materials:$
$
$
Qty$
Value$
Device$
Parts$
16$
10k$
Resistor$
R4,$R5,$R6,$R7,$R13,$R15,$R18,$R19,$R23,$R24,$R27,$R28,$
R33,$R34,$R37,$R38$
7$
1k$
Resistor$
R2,$R12,$R14,$R16,$R22,$R25,$R32$
8$
100k$
Resistor$
R3,$R8,$R17,$R20,$R26,$R29,$R36,$R39$
6$
100n$
Ceramic$Capacitor$$
C1,$C2,$C3,$C4,$C5,$C6$
2$
22R$
Resistor$
R49,$R50$
4$
220k$
Resistor$
R1,$R10,$R11,$R31$
3$
22uF$
electrolytic$capacitors$
C7,$C9,$C10$
4$
2N3906$
PNP$transistor$$
T1,$T2,$T3,$T4$
4$
330k$
Resistor$
R9,$R21,$R30,$R40$
2$
LM13600AN$
LM13600AN$
IC1,$IC3$
1$
TL074P$
TL074P$
IC6$
1$
N/A$
IDC$Socket$$
X2$
8$
N/A$
Jack$3.5mm$
CV_IN,$CV_IN_2,$INPUT,$INPUT_2,$OUTPUT,$OUTPUT_2,$
VELOCITY,$VELOCITY_2$
1$
N/A$
IC$Socket$$
N/A$
2$
N/A$
IC$Socket$$
N/A$
1$
N/A$
Ribbon$Cable$
N/A$
1$
Amazing$
Cookie$$
Stroopwafel$$
All manuals and user guides at all-guides.com
VVCA Velocity Voltage Controlled Amplifier
DIY Manual
©2018 Majella Audio
19
Thanks for your patience and soldering skills!
Enjoy your VVCA!
VVCA DIY Manual
version 1.0
08-2018
©2018
https://majella-audio.com
support@majella-audio.com
All manuals and user guides at all-guides.com
VVCA Velocity Voltage Controlled Amplifier
DIY Manual
©2018 Majella Audio
20
Designed and made in Holland
All manuals and user guides at all-guides.com

Popular Amplifier manuals by other brands

DM Engineering AUDIO-POD user guide

DM Engineering

DM Engineering AUDIO-POD user guide

Framus FRAMUS owner's manual

Framus

Framus FRAMUS owner's manual

BreatheAudio BA-6640 installation manual

BreatheAudio

BreatheAudio BA-6640 installation manual

Onkyo Integra P-388F instruction manual

Onkyo

Onkyo Integra P-388F instruction manual

Di-soric OLVTI 41 P3K-IBS manual

Di-soric

Di-soric OLVTI 41 P3K-IBS manual

Kramer VM-24HD user manual

Kramer

Kramer VM-24HD user manual

SIIG 1x8 HDMI 1.3 Distribution Amplifier Quick installation guide

SIIG

SIIG 1x8 HDMI 1.3 Distribution Amplifier Quick installation guide

Cambridge Audio Azur 340A user manual

Cambridge Audio

Cambridge Audio Azur 340A user manual

evertz 7700ADA7-EQ MultiFrame manual

evertz

evertz 7700ADA7-EQ MultiFrame manual

Pioneer GM-X1024 Service manual

Pioneer

Pioneer GM-X1024 Service manual

Nakamichi NKTA75.2 user manual

Nakamichi

Nakamichi NKTA75.2 user manual

Schertler Giulia Y manual

Schertler

Schertler Giulia Y manual

B&K ST140M owner's manual

B&K

B&K ST140M owner's manual

technetix AIMA3000.RPAS Product user manual

technetix

technetix AIMA3000.RPAS Product user manual

Magnat Audio MCD1050 Technical specifications

Magnat Audio

Magnat Audio MCD1050 Technical specifications

Lyngdorf Audio SDA 2175 owner's manual

Lyngdorf Audio

Lyngdorf Audio SDA 2175 owner's manual

Rotel RA-1572MKII owner's manual

Rotel

Rotel RA-1572MKII owner's manual

Vitus Audio SIA-030 owner's manual

Vitus Audio

Vitus Audio SIA-030 owner's manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.