Makita 6016 User manual

Drill Instruction manual
Bor Petunjuk penggunaan
Máy khoan Tài liu hng dn

6016
GB
VI
TH
ID

2
1013437 2013433
3013434 4013435
5013438 6001145
7013436
12
3
45
6
7
8
9

3
ENGLISH
Explanation of general view
SPECIFICATIONS
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
END009-1
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
.... Read instruction manual.
ENE032-1
Intended use
The tool is intended for drilling in wood, metal and plastic.
ENF001-1
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. This tool
should be grounded while in use to protect the operator
from electric shock. Use only three-wire extension cords
which have three-prong grounding-type plugs and three-
pole receptacles which accept the tool's plug.
GEA005-3
General Power Tool Safety
Warnings
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
Electrical safety
4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase
the risk of electric shock.
7. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
9. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
10. Use of power supply via a RCD with a rated
residual current of 30 mA or less is always
recommended.
1. Switch trigger
2. Lock button
3. Tighten
4. Chuck key
5. Depth gauge
6. Wing bolt
7. Limit mark
8. Brush holder cap
9. Screwdriver
Model 6016
Capacity Steel 16 mm
Wood 36 mm
No load speed (min-1)700
Overall length 365 mm
Net weight 4.4 kg
Safety class Class I

4
Personal safety
11. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
12. Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
13. Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch
on invites accidents.
14. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
15. Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
16. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
17. If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
Power tool use and care
18. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
19. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
20. Disconnect the plug from the power source and/or
the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
21. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
22. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
23. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
24. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
Service
25. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained.
26. Follow instruction for lubricating and changing
accessories.
27. Keep handles dry, clean and free from oil and
grease.
GEB101-1
DRILL SAFETY WARNINGS
1. Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
2. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not leave the tool running. Operate the tool
only when hand-held.
6. Do not touch the drill bit or the workpiece
immediately after operation; they may be
extremely hot and could burn your skin.
7. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation and
skin contact. Follow material supplier safety data.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product (gained
from repeated use) replace strict adherence to safety
rules for the subject product. MISUSE or failure to
follow the safety rules stated in this instruction
manual may cause serious personal injury.
FUNCTIONAL DESCRIPTION
CAUTION:
•Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Switch action (Fig. 1)
CAUTION:
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
“OFF” position when released.
To start the tool, simply pull the switch trigger. Release the
switch trigger to stop.
For continuous operation, pull the switch trigger and then
push in the lock button and then release the switch trigger.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.

5
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Installing top grip (auxiliary handle)
(Fig. 2)
Screw the top grip on the tool securely.
Installing or removing drill bit (Fig. 3)
To install the bit, place it in the chuck as far as it will go.
Tighten the chuck by hand. Place the chuck key in each of
the three holes and tighten clockwise. Be sure to tighten
all three chuck holes evenly.
To remove the bit, turn the chuck key counterclockwise in
just one hole, then loosen the chuck by hand.
After using the chuck key, be sure to return to the original
position.
Adjusting depth of drilling (Fig. 4)
The depth gauge is convenient for drilling holes of uniform
depth.
Loosen the wing bolt and adjust the depth gauge to the
desired depth. After adjusting, tighten the wing bolt.
OPERATION
CAUTION:
•Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
“OFF” position when released.
Drilling operation (Fig. 5)
Always use the top or back grip (auxiliary handle) and
firmly hold the tool by top or back grip and switch handle
during operations.
Drilling in wood
When drilling in wood, the best results are obtained with
wood drills equipped with a guide screw. The guide screw
makes drilling easier by pulling the bit into the workpiece.
Drilling in metal
To prevent the bit from slipping when starting a hole, make
an indentation with a center-punch and hammer at the
point to be drilled. Place the point of the bit in the
indentation and start drilling.
Use a cutting lubricant when drilling metals. The
exceptions are iron and brass which should be drilled dry.
CAUTION:
•Pressing excessively on the tool will not speed up the
drilling. In fact, this excessive pressure will only serve
to damage the tip of your bit, decrease the tool
performance and shorten the service life of the tool.
• There is a tremendous twisting force exerted on the
tool/bit at the time of hole breakthrough. Hold the tool
firmly and exert care when the bit begins to break
through the workpiece.
•Always secure small workpieces in a vise or similar
hold-down device.
•Avoid drilling in material that you suspect contains
hidden nails or other things that may cause the bit to
bind or break.
MAINTENANCE
CAUTION:
•Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
•Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
Replacing carbon brushes
Remove and check the carbon brushes regularly. Replace
when they wear down to the limit mark. Keep the carbon
brushes clean and free to slip in the holders. Both carbon
brushes should be replaced at the same time. Use only
identical carbon brushes. (Fig. 6)
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps. (Fig. 7)
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.

6
BAHASA INDONESIA
Penjelasan tampilan keseluruhan
SPESIFIKASI
•Karena kesinambungan program penelitian dan pengembangan kami, spesifikasi yang disebutkan di sini dapat
berubah tanpa pemberitahuan.
• Spesifikasi dapat berbeda dari satu negara ke negara lainnya.
END009-1
Simbol
Berikut ini adalah simbol-simbol yang digunakan pada
peralatan ini. Pastikan Anda mengerti makna masing-
masing simbol sebelum menggunakan alat.
.... Baca petunjuk penggunaan.
ENE032-1
Penggunaan
Mesin ini digunakan untuk membor kayu, logam dan
plastik.
ENF001-1
Pasokan daya
Mesin harus terhubung dengan pasokan daya listrik yang
bervoltase sama dengan yang tertera pada pelat nama,
dan hanya dapat dijalankan dengan listrik AC fase
tunggal. Mesin ini harus terarde (dibumikan) ketika
digunakan untuk melindungi operator dari sengatan listrik.
Gunakan hanya kabel ekstensi tiga-kawat yang
mempunyai steker tipe pengardean tiga-kaki dan stop
kontak tiga-kutub yang bisa dimasuki steker mesin.
GEA005-3
Peringatan Keselamatan Umum
Mesin Listrik
PERINGATAN! Bacalah semua peringatan
keselamatan dan semua petunjuk. Kelalaian mematuhi
peringatan dan petunjuk dapat menyebabkan sengatan
listrik, kebakaran dan/atau cedera serius.
Simpanlah semua peringatan dan
petunjuk untuk acuan di masa
depan.
Istilah “mesin listrik” dalam semua peringatan mengacu
pada mesin listrik yang dijalankan dengan sumber listrik
jala-jala (berkabel) atau baterai (tanpa kabel).
Keselamatan tempat kerja
1. Jaga tempat kerja selalu bersih dan
berpenerangan cukup. Tempat kerja yang
berantakan dan gelap mengundang kecelakaan.
2. Jangan gunakan mesin listrik dalam lingkungan
yang mudah meledak, misalnya jika ada cairan,
gas, atau debu yang mudah menyala. Mesin listrik
menimbulkan bunga api yang dapat menyalakan debu
atau uap tersebut.
3. Jauhkan anak-anak dan orang lain saat
menggunakan mesin listrik. Bila perhatian terpecah,
anda dapat kehilangan kendali.
Keamanan kelistrikan
4. Steker mesin listrik harus cocok dengan
stopkontak. Jangan sekali-kali mengubah steker
dengan cara apa pun. Jangan menggunakan
steker adaptor dengan mesin listrik berarde
(dibumikan). Steker yang tidak diubah dan
stopkontak yang cocok akan mengurangi risiko
sengatan listrik.
5. Hindari sentuhan tubuh dengan permukaan
berarde atau yang dibumikan seperti pipa,
radiator, kompor, dan kulkas. Risiko sengatan listrik
bertambah jika tubuh Anda terbumikan atau terarde.
6. Jangan membiarkan mesin listrik kehujanan atau
kebasahan. Air yang masuk ke dalam mesin listrik
akan meningkatkan risiko sengatan listrik.
1. Saklar pemicu
2. Tombol kunci
3. Kencangkan
4. Kunci cekam
5. Pengukur kedalaman
6. Baut kupu-kupu
7. Tanda batas
8. Tutup tempat sikat
9. Obeng
Model 6016
Kapasitas Baja 16 mm
Kayu 36 mm
Kecepatan tanpa beban (min-1)700
Panjang keseluruhan 365 mm
Berat bersih 4,4 kg
Kelas keamanan Kelas I

7
7. Jangan menyalahgunakan kabel. Jangan sekali-
kali menggunakan kabel untuk membawa,
menarik, atau mencabut mesin listrik dari
stopkontak. Jauhkan kabel dari panas, minyak,
tepian tajam, atau bagian yang bergerak. Kabel
yang rusak atau kusut memperbesar risiko sengatan
listrik.
8. Bila menggunakan mesin listrik di luar ruangan,
gunakan kabel ekstensi yang sesuai untuk
penggunaan di luar ruangan. Penggunaan kabel
yang sesuai untuk penggunaan luar ruangan
mengurangi risiko sengatan listrik.
9. Jika mengoperasikan mesin listrik di lokasi
lembap tidak terhindarkan, gunakan pasokan daya
yang dilindungi peranti imbasan arus (residual
current device - RCD). Penggunaan RCD
mengurangi risiko sengatan listrik.
10. Penggunaan pasokan daya melalui RCD dengan
kapasitas arus sisa 30 mA atau kurang selalu
dianjurkan.
Keselamatan diri
11. Jaga kewaspadaan, perhatikan pekerjaan Anda
dan gunakan akal sehat bila menggunakan mesin
listrik. Jangan menggunakan mesin listrik saat
Anda lelah atau di bawah pengaruh obat bius,
alkohol, atau obat. Sekejap saja lalai saat
menggunakan mesin listrik dapat menyebabkan
cedera diri yang serius.
12. Gunakan alat pelindung diri. Selalu gunakan
pelindung mata. Peralatan pelindung seperti masker
debu, sepatu pengaman anti-selip, helm pengaman,
atau pelindung telinga yang digunakan untuk kondisi
yang sesuai akan mengurangi risiko cedera diri.
13. Cegah penyalaan yang tidak disengaja. Pastikan
bahwa sakelar berada dalam posisi mati (off)
sebelum menghubungkan mesin ke sumber daya
dan/atau baterai, atau mengangkat atau
membawanya. Membawa mesin listrik dengan jari
Anda pada sakelarnya atau mengalirkan listrik pada
mesin listrik yang sakelarnya hidup (on) akan
mengundang kecelakaan.
14. Lepaskan kunci-kunci penyetel sebelum
menghidupkan mesin listrik. Kunci-kunci yang
masih terpasang pada bagian mesin listrik yang
berputar dapat menyebabkan cedera.
15. Jangan meraih terlalu jauh. Jagalah pijakan dan
keseimbangan sepanjang waktu. Hal ini
memungkinkan kendali yang lebih baik atas mesin
listrik dalam situasi yang tidak diharapkan.
16. Kenakan pakaian dengan baik. Jangan memakai
pakaian yang kedodoran atau perhiasan. Jaga
jarak antara rambut, pakaian, dan sarung tangan
Anda dengan bagian mesin yang bergerak.
Pakaian kedodoran, perhiasan, atau rambut panjang
dapat tersangkut pada bagian yang bergerak.
17. Jika tersedia fasilitas untuk menghisap dan
mengumpulkan debu, pastikan fasilitas tersebut
terhubung listrik dan digunakan dengan baik.
Penggunaan pembersih debu dapat mengurangi
bahaya yang terkait dengan debu.
Penggunaan dan pemeliharaan mesin listrik
18. Jangan memaksa mesin listrik. Gunakan mesin
listrik yang tepat untuk keperluan Anda. Mesin
listrik yang tepat akan menuntaskan pekerjaan
dengan lebih baik dan aman pada kecepatan sesuai
rancangannya.
19. Jangan gunakan mesin listrik jika sakelar tidak
dapat menyalakan dan mematikannya. Mesin listrik
yang tidak dapat dikendalikan dengan sakelarnya
adalah berbahaya dan harus diperbaiki.
20. Cabut steker dari sumber listrik dan/atau baterai
dari mesin listrik sebelum melakukan penyetelan,
penggantian aksesori, atau menyimpan mesin
listrik. Langkah keselamatan preventif tersebut
mengurangi risiko hidupnya mesin secara tak
sengaja.
21. Simpan mesin listrik jauh dari jangkauan anak-
anak dan jangan biarkan orang yang tidak paham
mengenai mesin listrik tersebut atau petunjuk ini
menggunakan mesin listrik. Mesin listrik sangat
berbahaya di tangan pengguna yang tak terlatih.
22. Rawatlah mesin listrik. Periksa apakah ada bagian
bergerak yang tidak lurus atau macet, bagian yang
pecah dan kondisi lain yang dapat mempengaruhi
penggunaan mesin listrik. Jika rusak, perbaiki
dahulu mesin listrik sebelum digunakan. Banyak
kecelakaan disebabkan oleh kurangnya pemeliharaan
mesin listrik.
23. Jaga agar mesin pemotong tetap tajam dan bersih.
Mesin pemotong yang terawat baik dengan mata
pemotong yang tajam tidak mudah macet dan lebih
mudah dikendalikan.
24. Gunakan mesin listrik, aksesori, dan mata mesin,
dll. sesuai dengan petunjuk ini, dengan
memperhitungkan kondisi kerja dan jenis
pekerjaan yang dilakukan. Penggunaan mesin listrik
untuk penggunaan yang lain dari peruntukan dapat
menimbulkan situasi berbahaya.
Servis
25. Berikan mesin listrik untuk diperbaiki hanya
kepada oleh teknisi yang berkualifikasi dengan
menggunakan hanya suku cadang pengganti yang
serupa. Hal ini akan menjamin terjaganya keamanan
mesin listrik.
26. Patuhi petunjuk pelumasan dan penggantian
aksesori.
27. Jagalah agar gagang kering, bersih, dan bebas
dari minyak dan gemuk.
GEB101-1
PERINGATAN KESELAMATAN
BOR
1. Gunakan gagang tambahan, jika disertakan
bersama mesin ini. Kehilangan kendali dapat
menyebabkan cedera.
2. Selalu pastikan Anda berdiri di atas alas yang
kuat.
Pastikan tidak ada orang di bawahnya bila Anda
menggunakan mesin di tempat tinggi.
3. Pegang mesin kuat-kuat.

8
4. Jauhkan tangan dari bagian yang berputar.
5. Jangan tinggalkan mesin dalam keadaan hidup.
Jalankan mesin hanya ketika digenggam tangan.
6. Jangan menyentuh mata bor atau benda kerja
segera setelah pengoperasian; suhunya mungkin
masih sangat panas dan dapat membakar kulit
Anda.
7. Bahan tertentu mengandung zat kimia yang
mungkin beracun. Hindari menghirup debu dan
persentuhan dengan kulit. Ikuti data keselamatan
bahan dari pemasok.
SIMPAN PETUNJUK INI.
PERINGATAN:
JANGAN biarkan kenyamanan atau terbiasanya Anda
dengan produk (karena penggunaan berulang)
menggantikan kepatuhan yang ketat terhadap aturan
keselamatan untuk produk yang terkait.
PENYALAHGUNAAN atau kelalaian mematuhi kaidah
keselamatan yang tertera dalam petunjuk ini dapat
menyebabkan cedera badan serius.
DESKRIPSI FUNGSI
PERHATIAN:
• Selalu pastikan bahwa mesin dalam keadaan mati dan
steker tercabut sebelum menyetel atau memeriksa
kerja mesin.
Kerja saklar (Gb. 1)
PERHATIAN:
•Sebelum memasukkan steker, selalu periksa apakah
picu saklar berfungsi dengan baik dan kembali ke
posisi “OFF” saat dilepas.
Untuk menjalankan mesin, cukup tarik picu saklarnya.
Lepaskan picu saklar untuk berhenti.
Untuk penggunaan terus-menerus, tarik picu saklar lalu
tekan tombol kunci dan kemudian lepas picu saklar.
Untuk membebaskan posisi terkunci, tarik picu saklar
sampai penuh, lalu lepaskan.
PERAKITAN
PERHATIAN:
• Selalu pastikan bahwa mesin dalam keadaan mati dan
steker tercabut sebelum melakukan pekerjaan apapun
pada mesin.
Cara memasang gagang atas (pegangan
tambahan) (Gb. 2)
Pasang gagang atas pada mesin dengan menggunakan
sekrup.
Memasang atau melepas mata bor (Gb. 3)
Untuk memasang mata bor, masukkan mata bor ke dalam
cekam sedalam mungkin. Kencangkan cekam dengan
tangan. Masukkan kunci cuk ke dalam tiga lubang yang
ada dan kencangkan searah jarum jam. Pastikan ketiga
lubang cekam dikencangkan secara seragam.
Untuk melepas mata bor, putar kunci cekam berlawanan
arah jarum jam pada satu lubang saja, lalu bebaskan
mata bor dengan tangan.
Setelah menggunakan kunci cekam, pastikan untuk
mengembalikannya ke posisi semula.
Menyetel kedalaman pengeboran (Gb. 4)
Pengukur kedalaman sangat tepat digunakan untuk
menghasilkan lubang-lubang pengeboran dengan
kedalaman yang seragam.
Kendurkan baut kupu-kupu dan setel pengukur
kedalaman pada kedalaman yang diinginkan. Setelah
penyetelan, kencangkan baut kupu-kupunya.
PENGGUNAAN
PERHATIAN:
• Sebelum memasukkan steker, selalu periksa apakah
picu saklar berfungsi dengan baik dan kembali ke
posisi “OFF” saat dilepas.
Pekerjaan pengeboran (Gb. 5)
Selalu gunakan gagang atas atau belakang (pegangan
tambahan) dan pegang mesin kuat-kuat pada gagang
atas atau belakang dan pegangan saklar selama
penggunaan.
Mengebor kayu
Bila mengebor kayu, hasil terbaik didapat dengan mata
bor kayu yang dilengkapi sekrup pemandu. Sekrup
pemandu mempermudah pengeboran dengan menarik
mata bor ke dalam benda kerja.
Mengebor logam
Untuk mencegah mata bor selip ketika mulai membuat
lubang, buatlah takik dengan penitik lalu palu pada titik
yang akan dilubangi. Letakkan ujung mata bor pada takik
dan mulailah membor.
Gunakan cairan pendingin saat mengebor logam.
Pengecualian untuk besi dan kuningan yang harus dibor
kering.
PERHATIAN:
•Menekan mesin secara berlebihan tidak akan
mempercepat pengeboran. Bahkan, tekanan yang
berlebihan hanya akan merusak mata bor Anda,
mengurangi kinerja mesin dan memperpendek usia
mesin.
• Akan timbul gaya puntir yang sangat kuat pada mesin/
mata bor saat menembus lubang. Pegang mesin
dengan kuat dan berhati-hatilah saat mata bor
menembus benda kerja.
•Tahan benda kerja berukuran kecil dengan penjepit
atau alat penahan lain.
• Hindari mengebor material yang Anda perkirakan ada
paku tersembunyi atau benda lain yang bisa
menyebabkan bengkok atau rusaknya mata bor.
PERAWATAN
PERHATIAN:
•Selalu pastikan bahwa mesin dimatikan dan steker
dicabut sebelum melakukan pemeriksaan atau
perawatan.
•Jangan sekali-kali menggunakan bensin, tiner, alkohol,
atau bahan sejenisnya. Penggunaan bahan demikian
dapat menyebabkan perubahan warna, perubahan
bentuk atau timbulnya retakan.

9
Mengganti sikat karbon
Lepas dan periksa sikat karbon secara teratur. Lepas
ketika aus sampai tanda batas. Jaga agar sikat karbon
tetap bersih dan tidak bergeser dari tempatnya. Kedua
sikat karbon harus diganti pada waktu yang sama. Hanya
gunakan sikat karbon yang sama. (Gb. 6)
Gunakan obeng untuk melepas tutup tempat sikat. Tarik
keluar sikat karbon yang aus, masukkan yang baru dan
pasang tutup tempat sikat. (Gb. 7)
Untuk menjaga KEAMANAN dan KEANDALAN mesin,
perbaikan, perawatan atau penyetelan lain harus
dilakukan oleh Pusat Layanan Resmi Makita dan selalu
gunakan suku cadang pengganti buatan Makita.

10
TING VIT
Gii thích v hình v tng th
THÔNG S K THUT
•Do chng trình nghiên cu và phát trin liên tc ca chúng tôi nên các thông s k thut trong ây có th thay i mà
không cn thông báo trc.
• Các thông s k thut có th thay i tùy theo tng quc gia.
END009-1
Ký hiu
Phn di ây cho bit các ký hiu c dùng cho thit
b. m bo rng bn hiu rõ ý ngha ca các ký hiu này
trc khi s dng.
.... c tài liu hng dn.
ENE032-1
Mc ích s dng
Dng c này dùng  khoan g, kim loi và nha.
ENF001-1
Ngun cp in
Dng c này ch c ni vi ngun cp in có in áp
ging nh ã ch ra trên bin tên và ch có th c vn
hành trên ngun in AC mt pha. Dng c này cn phi
c ni t trong lúc s dng  m bo ngi vn
hành không b iên git. Ch s dng các dây in ni dài
loi ba lõi vi các phích cm loi ba chu có tip t và
các  cm in ba chu dùng cho phích cm ca dng c.
GEA005-3
Cnh báo An toàn Chung dành
cho Dng c Máy
CNH BÁO! c tt c các cnh báo an toàn và
hng dn. Vic không tuân theo các cnh báo và
hng dn có th dn n in git, ho hon và/hoc
thng tích nghiêm trng.
Lu gi tt c cnh báo và hng
dn  tham kho sau này.
Thut ng “dng c máy” trong các cnh báo  cp n
dng c máy (có dây) c vn hành bng ngun in
chính hoc dng c máy (không dây) c vn hành
bng pin ca bn.
An toàn ti ni làm vic
1. Gi ni làm vic sch s và có  ánh sáng. Ni
làm vic ba bn hoc ti thng d gây ra tai nn.
2. Không vn hành dng c máy trong môi trng
cháy n, ví d nh môi trng có s hin din
ca các cht lng, khí hoc bi d cháy. Các dng
c máy to tia la in có th làm bi hoc khí bc
cháy.
3. Gi tr em và ngi ngoài tránh xa ni làm vic
khi ang vn hành dng c máy. S xao lãng có th
khin bn mt kh nng kim soát.
An toàn v in
4. Phích cm ca dng c máy phi khp vi  cm.
Không bao gi c sa i phích cm theo bt
k cách nào. Không s dng bt k phích chuyn
i nào vi các dng c máy c ni t (tip
t). Các phích cm còn nguyên vn và  cm phù
hp s gim nguy c in git.
5. Tránh  c th tip xúc vi các b mt ni t
hoc tip t nh ng ng, b tn nhit, bp ga
và t lnh. Nguy c b in git s tng lên nu c
th bn c ni t hoc tip t.
6. Không  dng c máy tip xúc vi ma hoc
trong iu kin m t. Nc lt vào dng c máy
s làm tng nguy c in git.
7. Không lm dng dây. Không bao gi s dng dây
 mang, kéo hoc tháo phích cm dng c máy.
Gi dây tránh xa ngun nhit, du, các mép sc
hoc các b phn chuyn ng. Dây b hng hoc
b ri s làm tng nguy c in git.
8. Khi vn hành dng c máy ngoài tri, hãy s
dng dây kéo dài phù hp cho vic s dng ngoài
tri. Vic dùng dây phù hp cho vic s dng ngoài
tri s gim nguy c in git.
9. Nu bt buc phi vn hành dng c máy  ni
m t, hãy s dng ngun cp in c bo v
bng thit b ngt dòng in rò (RCD). Vic s
dng RCD s gim nguy c in git.
1. Cn khi ng công tc
2. Nút khóa
3. Vn cht
4. Khóa ngàm
5. Thanh o sâu
6. Bu-lông tai vn
7. Vch gii hn
8. Np gi chi
9. Tuc-n-vít
Kiu6016
Dung lng Thép 16 mm
G36 mm
Tc  không ti (phút-1)700
Chiu dài tng th365 mm
Trng lng tnh 4,4 kg
Cp  an toàn Cp I

11
10. Chúng tôi luôn khuyên bn s dng ngun cp
in qua thit b RCD có th ngt dòng in d
nh mc 30 mA hoc thp hn.
An toàn cá nhân
11. Luôn tnh táo, quan sát nhng vic bn ang làm
và s dng nhng phán oán theo kinh nghim
khi vn hành dng c máy. Không s dng dng
c máy khi bn ang mt mi hoc chu nh
hng ca ma tuý, ru hay thuc. Ch mt
khonh khc không tp trung khi ang vn hành dng
c máy cng có th dn n thng tích cá nhân
nghiêm trng.
12. S dng thit b bo h cá nhân. Luôn eo thit b
bo v mt. Các thit b bo h nh mt n chng
bi, giày an toàn chng trt, m bo h hay thit b
bo v thính giác c s dng trong các iu kin
thích hp s giúp gim thng tích cá nhân.
13. Tránh vô tình khi ng dng c máy. m bo
công tc  v trí off (tt) trc khi ni ngun in
và/hoc b pin, cm hoc mang dng c máy. Vic
mang dng c máy khi ang t ngón tay  v trí công
tc hoc cp in cho dng c máy ang bt thng
d gây ra tai nn.
14. Tháo mi khoá hoc chìa vn iu chnh trc khi
bt dng c máy. Vic chìa vn hoc khoá vn còn
gn vào b phn quay ca dng c máy có th dn
n thng tích cá nhân.
15. Không vi quá cao. Luôn gi thng bng tt và có
ch  chân phù hp. iu này cho phép iu khin
dng c máy tt hn trong nhng tình hung bt ng.
16.
n mc phù hp. Không mc qun áo rng hay
eo  trang sc. Gi tóc, qun áo và gng tay
tránh xa các b phn chuyn ng.
Qun áo rng,
 trang sc hay tóc dài có th mc vào các b phn
chuyn ng.
17. Nu các thit b c cung cp  kt ni các thit
b thu gom và hút bi, hãy m bo chúng c
kt ni và s dng hp lý. Vic s dng thit b thu
gom bi có th làm gim nhng mi nguy him liên
quan n bi.
S dng và bo qun dng c máy
18. Không dùng lc i vi dng c máy. S dng
úng dng c máy cho công vic ca bn. S
dng úng dng c máy s giúp thc hin công vic
tt hn và an toàn hn theo giá tr nh mc c
thit k ca dng c máy ó.
19. Không s dng dng c máy nu công tc không
bt và tt c dng c máy ó. Mi dng c máy
không th iu khin c bng công tc u rt
nguy him và cn c sa cha.
20. Rút phích cm ra khi ngun in và/hoc ngt
kt ni b pin khi dng c máy trc khi thc
hin bt k công vic iu chnh, thay i ph
tùng hay ct gi dng c máy nào. Nhng bin
pháp an toàn phòng nga này s gim nguy c vô
tình khi ng vô tình dng c máy.
21. Ct gi các dng c máy không s dng ngoài
tm vi ca tr em và không cho bt k ngi nào
không có hiu bit v dng c máy hoc các
hng dn này vn hành dng c máy. Dng c
máy s rt nguy him nu c s dng bi nhng
ngi dùng cha qua ào to.
22. Bo qun dng c máy. Kim tra tình trng lch
trc hoc bó kp ca các b phn chuyn ng,
hin tng nt v ca các b phn và mi tình
trng khác mà có th nh hng n hot ng
ca dng c máy. Nu có hng hóc, hãy sa cha
dng c máy trc khi s dng. Nhiu tai nn xy
ra là do không bo qun tt dng c máy.
23. Luôn gi cho dng c ct c sc bén và sch
s. Nhng dng c ct c bo qun tt có mép ct
sc s ít b kt hn và d iu khin hn.
24. S dng dng c máy, ph tùng và u dng c
ct, v.v... theo các hng dn này, có tính n iu
kin làm vic và công vic c thc hin. Vic s
dng dng c máy cho các công vic khác vi công
vic d nh có th gây nguy him.
Bo dng
25.  nhân viên sa cha  trình  bo dng
dng c máy ca bn và ch s dng các b phn
thay th ng nht. Vic này s m bo duy trì
c  an toàn ca dng c máy.
26. Tuân theo hng dn dành cho vic bôi trn và
thay ph tùng.
27. Gi tay cm khô, sch, không dính du và m.
GEB101-1
CNH BÁO AN TOÀN DÀNH CHO
MÁY KHOAN
1. S dng các tay cm ph nu c cung cp kèm
theo dng c. Vic mt kh nng kim soát có th
dn n thng tích cá nhân.
2. Luôn m bo bn có ch t chân vng chc.
m bo rng không có ai  bên di khi s dng
dng c  trên cao.
3. Cm chc dng c.
4. Gi tay tránh xa các b phn quay.
5. Không  mc dng c hot ng. Ch vn hành
dng c khi cm trên tay.
6. Không chm vào u mi khoan hay vt gia công
ngay sau khi vn hành; chúng có th rt nóng và
có th gây bng da.
7. Mt s vt liu có th cha hoá cht c. Phi cn
trng tránh hít phi bi và  tip xúc vi da. Tuân
theo d liu an toàn ca nhà cung cp vt liu.
LU GI CÁC HNG DN NÀY.
CNH BÁO:
KHÔNG c  s thoi mái hay quen thuc vi sn
phm (có c do s dng nhiu ln) thay th vic
tuân th nghiêm ngt các quy nh v an toàn dành
cho sn phm này. VIC DÙNG SAI hoc không tuân
theo các quy nh v an toàn c nêu trong tài liu
hng dn này có th dn n thng tích cá nhân
nghiêm trng.
MÔ T CHC NNG
CN TRNG:
•Phi luôn m bo rng dng c ã c tt in và
ngt kt ni trc khi chnh sa hoc kim tra chc
nng ca dng c.

12
Hot ng công tc (Hình 1)
CN TRNG:
•Trc khi cm in vào dng c, luôn luôn kim tra
xem cn khi ng công tc có hot ng bình thng
hay không và tr v v trí “OFF” (TT) khi nh ra.
 khi ng dng c, ch cn kéo cn khi ng công
tc. Nh cn khi ng công tc ra  dng.
 vn hành liên tc, hãy kéo cn khi ng công tc,
sau ó nhn nút khóa và sau ó nh cn khi ng công
tc ra.
 dng dng c t v trí ã khóa, hãy kéo cn khi ng
công tc ht mc, sau ó nh ra.
LP RÁP
CN TRNG:
•Luôn luôn m bo rng dng c ã c tt và tháo
phích cm trc khi dùng dng c thc hin bt c
công vic nào.
Lp t tay cm trên nh (tay cm ph)
(Hình 2)
Vn tay cm trên nh dng c tht cht.
Lp hoc tháo g mi khoan (Hình 3)
 lp t u mi, hãy lp nó vào trong ngàm kp ht
mc có th. Vn phn ngàm kp li bng tay. t khóa
ngàm vào mt trong ba l nh ri vn cht theo chiu kim
ng h. m bo vn cht c ba l ngàm u nhau.
 tháo mi khoan, hãy xoay khóa ngàm ngc chiu
kim ng h ch  mt l, sau ó vn lng b phn ngàm
bng tay.
Sau khi s dng khóa ngàm, cn m bo tr nó li v trí
ban u.
iu chnh chiu sâu khoan (Hình 4)
Thanh o sâu rt thun tin  khoan các l có chiu sâu
ng nht.
Vn lng bu-lông tai vn và iu chnh thanh o sâu n
 sâu mong mun. Sau khi iu chnh, vn cht bu-lông
tai vn li.
VN HÀNH
CN TRNG:
•Trc khi cm in vào dng c, luôn luôn kim tra
xem cn khi ng công tc có hot ng bình thng
hay không và tr v v trí “OFF” (TT) khi nh ra.
Thao tác khoan (Hình 5)
Luôn s dng tay cm trên nh hoc phía sau (tay cm
ph tr) và gi cht dng c bng tay cm trên nh hoc
phía sau và i tay cm trong lúc vn hành.
Khoan vào g
Khi khoan vào g,  có kt qu tt nht cn s dng các
mi khoan dùng  khoan g và vít dn. Vít dn giúp
khoan d dàng hn bng cách kéo u mi vào trong vt
gia công.
Khoan vào kim loi
 phòng nga u mi b trt ra lúc bt u khoan l,
hãy to mt vt lõm bng cách dùng dùi c tâm và óng
vào im cn khoan. t u mi khoan vào ch lõm này
và bt u khoan.
S dng du nhn  ct khi khoan kim loi. Tr các
trng hp dùng st và ng thau cn phi c khoan
khô.
CN TRNG:
•Nhn dng c quá mc s không tng tc  khoan lên
c. Trên thc t, vic nhn mnh thêm này s ch
làm gây hng u mi ca bn, gim hiu nng và tui
th hot ng ca dng c.
•S có lc xoay rt ln trên dng c/mi khoan lúc l
khoan c xuyên thng. Gi cht dng c và chun
b ghìm lc quán tính li khi mi khoan xuyên thng vt
gia công.
•Luôn luôn gi cht các vt gia công có kích thc nh
bng kìm hoc dng c kp tng t.
•Tránh khoan vào vt liu mà bn nghi ng có cha
inh ngm hoc nhng th khác có th làm kt hoc
gãy u mi.
BO TRÌ
CN TRNG:
• Hãy luôn chc chn rng dng c ã c tt và ngt
kt ni trc khi c gng thc hin vic kim tra hay
bo dng.
•Không bao gi dùng xng, ét xng, dung môi, cn
hoc hóa cht tng t. Có th xy ra hin tng mt
màu, bin dng hoc nt v.
Thay th các chi các-bon
Hãy tháo và kim tra các chi các-bon nh k. Thay th
khi chi ã mòn n vch gii hn. Hãy gi cho các chi
các-bon sch s và không qun vào trong các u gi.
Các chi các-bon nên c thay th cùng lúc. Hãy s
dng các chi các-bon ging nhau. (Hình 6)
Hãy s dng mt tuc-n-vít  tháo các np gi chi.
Hãy tháo các chi các-bon ã b mòn, lp vào các chi
mi và vn cht các np gi chi. (Hình 7)
 m bo AN TOÀN và TIN CY ca sn phm, vic
sa cha hoc bt c thao tác bo trì, iu chnh nào u
phi c thc hin bi các Trung tâm Dch v c y
quyn ca Makita (Makita Authorized Service Center),
luôn s dng các ph tùng thit b thay th ca Makita.

13
!"#"$%&
'(")*+,"&-)./0//).%123$4
!"#$%&'()*+),
!!"#$%&'())(*+,"+-,(-.'/01234/5"(%06(& 76%!"#$%& 8,%9:2';(!4(3<"!%)=(*>?/?"@A%(' !B2@$0"1B2&CD,ED0C967,%&1',&<F,G*(?26-&F",(
!8,%9:2';(!4(3%('17)76(&)/"CB<"17623B*3!GH
END009-1
!"#$"%&'(
76%CB"@A+#%=/I2/)JKLG@$<M,=;(F*/?%NB)*KL EB*DHO)J(+-(9F9(0
8%&=/I2/)JKL<F,!8,(<')6%")(*<M,&("
.... %6("+:69#%)(*<M,&("
ENE032-1
!"#$%&'()*+,(-)%./,(0.,
!+*#$%&9#%"@A<M,=;(F*/?!'(3C9,E2F3 12342(=7.)
ENF001-1
12%!32456
7,%&!M#$%976%!+*#$%&9#%)/?!+*#$%&'6(0CPG@$9@1*&!+2#$%"CPPQ(7(9G@$
*3?NC-,<"BQ(08,%9:2!+*#$%&9#% 123'37,%&<M,CPPQ()*31==2/?
1??!P=!D@0-!G6("/A" 7,%&!M#$%976%=(0D."<"8K3<M,&("!4#$%
BQ%&)/"R:,BS.?/7.&("'())(*T:)CPPQ(D:D <M,176=(0CP76%1??
=(9=(0G@$9@B2/U)1??=(98(123!7,(*/?1??=(9*:!G6("/A"
GEA005-3
-()*./#01")0-2)$3&#1456!#7
*-8/9#7$/#:;;<)=592:3
!"#$%&'(! ')#(!"#$%&'(*+#(!,#-./'*0123/4!"#3(4(5
61789-*
!"#$%&'()*+,),"%-."/,012345-."3252."6+7!4&"81"9:&7;4
<=>/!)6$??@"AB1, $?$=%>345/=#01$6>#+**"6/9B*1C&"7#>"C3#7
*>?@85>A)-()*./#0B&,-()B0,0()=5C7D$1
:2"*3E0!"#$%&#")7#F7G0#0)-.
+;(-6( "!+*#$%&9#%CPPQ(#<"+;(!7#%""@A F9(0TO& !+*#$%&9#%CPPQ( (9@
=(0) G@$G;(&("ED0<M,)*31=CPPQ( F*#%!+*#$%&9#%CPPQ( (C*,=(0) G@$
G;(&("ED0<M,1?7!7%*@$
)720$8,#9:4+,(;.<=>?/>@2(2=
1. #AB8;.<=>?/>@2(2=CDE0?)720'&,2#B8&0?B'(56'732( 4#A"G@$
*)*3!)3*3)3F*#%9#DGO?%('";(CB=:6)(*!).D%N?/7.!F7NCD,
2. ,432CFE(2=-)%./,(0.,566G2C='92;>?/,2!-1H#12%%&-IH#
-F3= C='J2=>?/>?/0?+,(-D87 1K2L D%.,M"N=O(>?/0?)"P'0I:QH
5756 !+*#$%&9#%CPPQ('3=*,(&B*3)(0CP!4#$%'NDM"-"
VNW"R&
F*#%)X(YD/&)26(-
3.
*:3/;-)<9+-=$*>?@ 9A&'BC!!/'&D('2:)<(BAE$,F6=D?"#/18<G+
$!A&D'8-&';HHI#
!"#%D:)E7#*!82:%"F)1"9G."<=>-HI:JK/:DC
!"#-8*-H%
)720$8,#9:4#E2=566G2
4. $8:R1+,(-)%./,(0.,566G2QE,(;,#?1:I-QE2%:I ,432#:#B$8(
$8:R15037321%P?C#S ,432CFE$8:R1,&B#T$-Q,%*1:I
-)%./,(0.,
566G2>?/Q3,'24#H= B2/U)G@$C96T:)D/D1B2&123!7,(*/?CPG@$!8,()/"
4%D@'3M6-02D+-(9!=@$0&8%&)(*!).DCPPQ(MZ%7
5. %&7:(,432CDE%32(124':0O:'1:I;.<=OH7>?/Q3,'24#H= -F3= >3,
-)%./,(=@2)720%E,= -Q2D"(QE0 B8&QAE-4T= 9@+-(9!=@$0&G@$'3
!).DCPPQ(MZ%7=:&8OA" F()*6(&)(08%&+NK=/9R/=)/?4#A"
1. =-.7ML=/$&&("
2. BNW92Z%+
3. 8/"
4. B*31'8/"F/-'/?
5. !)'-/D+-(92O)
6. =2/)!)2@0-F(&B2(
7. 8@D';()/D
8. V(B[DG@$0OD1B*&
9. C8+-&
*N6" 6016
+-(9'NE2F3 16 99.
C9, 36 99.
+-(9!*Z-8K3F9N"!B26( (*%?76%"(G@)700
+-(90(-ED0*-9 365 99.
"A;(F"/)=NG\. 4.4 )).
9(7*]("+-(9B2%D^/0+2(=I

14
6. ,432CDE-)%./,(0.,566G2JA1=<@2D%.,,4A3C='92;-$U41F.<= "A;(
G@$CF2!8,(CB<"!+*#$%&9#%CPPQ('3!4.$9+-(9!=@60&8%&)(*!).D
CPPQ(MZ%7
7. ,432CFE'2456,432(503-D02&'0 ,432CFE'2456-;./,41 #V(
D%., J,#$8:R1-)%./,(0.,566G2 -1TI'2456CDED32(!21
)720%E,= =<@20:= +,(0?)0 D%.,FH<='37=>?/-)8./,=>?/ =(0G@$
M;(*NDF*#%4/")/"'3!4.$9+-(9!=@$0&8%&)(*!).DCPPQ(MZ%7
8. +P&>?/CFE(2=-)%./,(0.,566G2=,1,2)2% )7%CFE'24Q3,
;37(>?/-D02&'01:I(2=924=,1,2)2% )(*<M,=(0G@$
!F9(3=9)/?&("^(0"%)%(+(*'32D+-(9!=@$0&8%&)(*!).D
CPPQ(MZ%7
9. D21QE,(CFE(2=-)%./,(0.,566G2C='J2=>?/-$U41F.<= CDECFE
,"$1%P*$G,(1:=1%&B'56%:/7 (RCD) )(*<M,RCD '32D
+-(9!=@$0&8%&)(*!).DCPPQ(MZ%7
10. +,B=&=@2CDECFEBD83(!32456O32= RCD >?/0?1%&B'56%:/7
C=,:Q%2503-1H= 30 mA -'0,
)720$8,#9:4'37=I"))8
11. CDE%&0:#%&7:( B8&':(-1Q-'0,732)"P1@28:(>@2'H/(C#,4A3
B8&CFE'20:W'@2=V1C=+P&CFE(2=-)%./,(0.,566G2 ,432CFE
(2=-)%./,(0.,566G2C=+P&>?/)"P1@28:(-D=./,4 D%.,C=
'92;>?/0V=-02!2142-';QH# -)%./,(#./0B,81,X,8*D%.,
12%CFE42 M/$-8K3G@$8(D+-(9*39/D*3-/&!9#$%);(2/&<M,&("
!+*#$%&9#%CPPQ(%('G;(<F,+NKCD,*/??(D!'Z?%06(&*N"1*&
12. CFE,"$1%P*$G,(1:='37=I"))8 '70B73=Q2$G,(1:=-'0,
%NB)*KLBQ%&)/" !M6" F",()())/"VNW" *%&!G,(".*^/0)/"2#$" F9-)
".*^/0 F*#%!+*#$%&BQ%&)/")(*CD,0."G@$<M,<"=^(4G@$!F9(3=9'3
M6-02D)(*?(D!'Z?
13. $G,(1:=503CDE-$Y#CFE(2=,432(503Q:<(C! Q%7!',I732'7HQF*
,4A3C=Q@2BD=3($Y#13,=-F./,0Q3,1:IBD83(!32456 B8&/D%.,
F"#BIQ-Q,%?/ D%.,13,=12%41D%.,J.,-)%./,(0., )(*=%D
".A-9#%?*.!-K=-.7ML!4#$%T#%!+*#$%&9#%CPPQ( F*#%)(*M(*L'CP
!+*#$%&9#%CPPQ(<"8K3G@$!B[D=-.7ML%0:6%('";(CB=:6)(*!).D
%N?/7.!F7N
14. =@21"WB!$%:IBQ3(D%.,$%&B!,,113,=>?/!&-$Y#-)%./,(0.,
566G2 B*31'F*#%)NI1'G@$!=@0?+,(&%0:6<"M.A"=6-"G@$F9N"CD,8%&
!+*#$%&9#%CPPQ(%('G;(<F,+NKCD,*/??(D!'Z?
15. ,432>@2(2=C=%&4&>?/'"#-,.<,0 !:#>3212%4.=B8&12%
>%(Q:7CDE-D02&'0Q8,#-782 !4*(3'3G;(<F,+-?+N9
!+*#$%&9#%CPPQ(CD,D@8OA"<"=T(")(*KLG@$C96+(D+.D
16. BQ3(124CDE-D02&'0 ,432'70-)%./,(BQ3(124>?/D870-1H=
5$ D%.,'70-)%./,($%&#:I #AB8503CDE-'E=O0 -'.<,OE2 B8&
J"(0.,,4A3C18EFH<='37=>?/-)8./,=>?/ !=#A%R,(*N69*6(9 !+*#$%&B*3D/?
F*#%R9G@$9@+-(90(-%('!8,(CB7.D<"M.A"=6-"G@$!+2#$%"G@$
17. D210?12%!:#,"$1%P*'@2D%:I#A#B8&!:#-1TIM"N=57EC=
'J2=>?/ CDEQ%7!',I7325#E-F./,0Q3,B8&CFE(2=,"$1%P*=:<=
,432(-D02&'0 )(*<M,!+*#$%&D:D123'/D!)Z?VNW"'3M6-02D
%/"7*(0G@$!).D'()VNW"R&CD,
12%CFEB8&#AB8-)%./,(0.,566G2
18. ,432MZ=CFE-)%./,(0.,566G2 CFE-)%./,(0.,566G2>?/-D02&'0
1:I12%CFE(2=+,()"P !+*#$%&9#%CPPQ(G@$!F9(3=9'3G;(<F,CD,
&("G@$9@B*3=.G\.^(4123B2%D^/0)-6(7(98@D+-(9=(9(*T
8%&!+*#$%&G@$CD,*/?)(*%%)1??9(
19. ,432CFE-)%./,(0.,566G2 D21'7HQF*503'202%J-$Y#$Y#5#E
!+*#$%&9#%CPPQ(G@$+-?+N9D,-0=-.7MLC96CD,!B_"=.$&%/"7*(0123
7,%&CD,*/?)(*Y6%91Y9
20. J,#$8:R1!21BD83(!32456 B8&/D%.,F"#BIQ-Q,%?/,,1
!21-)%./,(0.,566G213,=>@212%$%:IBQ3( -$8?/4=,"$1%P*
-'%H0 D%.,!:#-1TI-)%./,(0.,566G2 -.\@)(*BQ%&)/"D,("+-(9
B2%D^/0D/&)26(-'3M6-02D+-(9!=@$0&8%&)(*!B[D<M,&("
!+*#$%&9#%CPPQ(%06(&C967/A&<'
21. !:#-1TI-)%./,(0.,566G2>?/5035#ECFE(2=CDED32(!210.,-#T1
B8&,432,="W2QCDEI"))8>?/503)"E=-)41:I-)%./,(0.,566G2
D%.,)@2B=&=@2-D832=?<CFE(2=-)%./,(0.,566G2 !+*#$%&9#%
CPPQ('3!B_"%/"7*(0!9#$%%0:6<"9#%8%&R:,G@$C96CD,*/?)(*V`)%?*9
22. 12%#AB8%:1[2-)%./,(0.,566G2 Q%7!',I12%$%&1,I>?/
503JA1QE,(D%.,12%-F./,0Q3,+,(FH<='37=
>?/-)8./,=>?/ 12%
BQ1D:1+,(FH<='37= D%.,'92;,./=S >?/,2!'3(O81%&>I
Q3,12%>@2(2=+,(-)%./,(0.,566G2 D210?)720-'?4D24 CDE
=@2-)%./,(0.,566G25$L3,0BL013,=12%CFE(2= %N?/7.!F7N
';("-"9()!).D'())(*D:12*/)J(!+*#$%&9#%CPPQ(%06(&C96
T:)7,%&
23. 8:I)720)0B8&>@2)720'&,2#-)%./,(0.,12%Q:#,4A3-'0,
!+*#$%&9#%)(*7/DG@$9@)(*D:12%06(&T:)7,%&1239@8%?)(*7/D+9
9/)'39@BaIF(7.D8/D",%0123+-?+N9CD,&6(0)-6(
24. CFE-)%./,(0.,566G2 ,"$1%P*-'%H0 B8&7:'#"'H<=-$8.,( \8\
Q20)@2B=&=@2#:(18327 ;H!2%P2'92;12%>@2(2=B8&
(2=>?/!&8(0.,>@2 )(*<M,!+*#$%&9#%CPPQ(!4#$%G;(&("%#$""%)
!F"#%'()G@$);(F"DC-,%('G;(<F,!).D%/"7*(0
12%I%H12%
25. =@2-)%./,(0.,566G2-+E2%:II%H12%!21F32(L3,0
>?/O32=12%
%:I%,(]#4CFE,&5D83BII-#?471:=->32=:<= !4*(3'3G;(<F,
)(*<M,!+*#$%&9#%CPPQ(9@+-(9B2%D^/0
26.
.JEB1%E%#-!"#3(4("#<(?#A9/)'/&D(3/4?#A$./=D2(
'C.?AFK$LAE-
27. #AB80.,!:ICDEBDE( '&,2# B8&5030?=<@20:=B8&!2%&I?
-$Z^,=

15
GEB101-1
-()*./#01")0-2)$3&#1456!#7H2I)0
:;;<)
1. CFE0.,!:I-'%H0 JE20?021:I-)%./,( )(*=:I!=@0+-(9+-?+N9
%('G;(<F,!).D)(*?(D!'Z?
2. Q%7!',II%H-7P>?/4.=CDE0?)7200:/=)(-'0,
D21CFE(2=-)%./,(0.,C=;.<=>?/'A( %&7:(,432CDE0?)=,4A3#E2=
832(
3. !:I-)%./,(0.,CDEB=3=
4. %&7:(,432CDE0.,':0O:'1:IFH<='37=>?/D0"=5#E
5. ,432$83,4CDE-)%./,(0.,>@2(2=)E2(57ECFE(2=-)%./,(0.,C=
+P&>?/J.,,4A3->32=:<=
6. DE20':0O:'1:I#,1'732=D%.,FH<=(2=>:=>?>?/>@2(2=-'%T!
-=./,(!21#,1'732=D%.,FH<=(2=,2!0?)720%E,='A(B8&
871OH7D=:(+,()"P5#E
7. 7:'#"I2(,432(,2!0?'2%-)0?>?/-$_=;H[ %&7:(,432'A##0M"N=
D%.,CDE'2%-D832=:<=':0O:'1:I%32(124 $`HI:QHQ20+E,0A8
#E2=)720$8,#9:4+,(OAEO8HQ7:'#"
3J[email protected].)$-()B0,0()*D&I)0KC
)@2-Q.,=:
,432CDE)720503%&0:#%&7:(D%.,)720)"E=-)41:IO8HQ9:Pa*
(!2112%CFE(2=L<@2D824)%:<() ,4A3-D=.,12%$`HI:QHQ20
1b-1Pa*#E2=)720$8,#9:4C=12%CFE(2=O8HQ9:Pa*,432(
-)%3()%:# 12%CFE(2=,432(503-D02&'0D%.,12%503$`HI:QHQ20
1b-1Pa*#E2=)720$8,#9:4C=)A30.,CFE(2==?<,2!13,CDE-1H#
12%I2#-!TI,432(%"=B%(
-()#LF@)6>)8=()7)0
+E,)7%%&7:(:
!7*-'=%?<F,1"6<'-6(=-.7ML!+*#$%&9#%%0:6<"7;(1F"6&B[D!+*#$%&
123T%DB2/U)!+*#$%&9#%%%))6%"B*/?7/A&F*#%7*-'=%?)(*G;(
&("8%&!+*#$%&9#%
%)*+,)-)./0-!1234( (5)6+78 1)
+E,)7%%&7:(:
!)6%"!=@0?B2/U)!+*#$%&9#% <F,7*-'=%?-6(=-.7ML=/$&&("=(9(*TG;(
&("CD,%06(&T:)7,%& 123)2/?CB0/&7;(1F"6& "OFF#!9#$%B26%0
!B[D<M,!+*#$%&9#%ED0DO&=-.7ML=/$&&(" B26%0=-.7ML=/$&&("!4#$%F0NDG;(
&("
T,(7,%&)(*<M,&("%06(&76%!"#$%& DO&=-.7ML=/$&&(" )DBNW92Z%+ 12,-
B26%0=-.7ML=/$&&("
T,(7,%&)(*!2.)<M,&("!+*#$%&9#%<"7;(1F"6&2Z%+ <F,DO&=-.7ML=/$&&("
'"=ND '()"/A"B26%0=-.7ML
>)838,>#@
+E,)7%%&7:(:
!7*-'=%?<F,1"6<'-6(=-.7ML!+*#$%&9#%%0:6<"7;(1F"6&B[D!+*#$%&
123T%DB2/U)!+*#$%&9#%%%))6%"D;(!"."&("<Db )/?!+*#$%&9#%
%)*9*:%0;<=)>?";<=).;. (>@0?";A!*2>) (5)6
+782)
8/"=)*:D,(9'/?D,("?"8%&!+*#$%&9#%<F,1"6"
%)*32<3"B-C*@0D0<<0%!1E). (5)6+78 3)
!9#$%7,%&)(*7.D7/A&D%)=-6(" <F,<=6D%)=-6("2&<"F/-'/?'"=ND 8/"
1"6"F/-'/?D,-09#% <M,B*31'8/"F/-'/?8/"G/A&=(9*:7(9!8Z9"(c.)(
%06(2#9 8/"F/-'/?G/A&=(9*:<F,!G6()/"
T,(7,%&)(*T%DD%)=-6(" <F,F9N"B*31'8/"F/-'/?G-"!8Z9"(c.)(
!4@0&*:!D@0- '()"/A"+2(0F/-'/?D,-09#%
F2/&'()<M,B*31'8/"F/-'/? <F,!)Z?B*31')2/?!8,(G@$7;(1F"6&!D.9
%)*9*";F1)>$G%/0-%)*A?): (5)6+78 4)
!)'-/D+-(92O)!F9(3=9G@$'3<M,=;(F*/?*:!'(3G@$9@+-(92O)!G6()/"
+2(0=)*:F(&B2(!4#$%B*/?!)'-/D+-(92O)<F,CD,*3D/?7(97,%&)(*
F2/&'()G@$B*/?12,- <F,8/"=)*:F(&B2(<F,1"6"
>)8GM"7)0
+E,)7%%&7:(:
!)6%"!=@0?B2/U)!+*#$%&9#% <F,7*-'=%?-6(=-.7ML=/$&&("=(9(*TG;(
&("CD,%06(&T:)7,%& 123)2/?CB0/&7;(1F"6& "OFF#!9#$%B26%0
%)*A?): (5)6+78 5)
<M,D,(9'/?D,("?"F*#%D,("F2/& (9#%'/?!=*.9) !=9%123'/?!+*#$%&9#%
<F,1"6"D,-0D,(9'/?D,("?"F*#%D,("F2/& 1239#%'/?=-.7ML<"
*3F-6(&)(*<M,&("
12%-!2&50E
!4#$%<F,CD,R2D@<")(*!'(3C9,+-*<M,=-6("!'(3C9,+-?+:6)/?=)*:";(
=)*:";('3M6-0<F,)(*!'(3&6(08OA" ED0)(*DO&D%)=-6("2&<"M.A"&("
12%-!2&]8D&
!4#$%BQ%&)/"D%)=-6("!2#$%"!9#$%!*.$9!'(3*: <F,G;(*%07/DD,-0!F2Z)
!'(3";(H:"0L123+,%"<"'NDG@$'3!'(3 -(&B2(0D%)=-6("G@$*%07/D
123!*.$9!'(3
<M,=(*F26%2#$"=;(F*/?)(*7/D!9#$%!'(3E2F3 0)!-,")(*!'(3!F2Z)
123G%&!F2#%& YO$&+-*!'(31??1F,&
+E,)7%%&7:(:
!)(*%%)1*&)D?"!+*#$%&9#%C96M6-0<F,)(*!'(3!*Z-8OA" 7(9
8,%!GZ''*.&12,- 1*&)DG@$9()!)."CB'3G;(<F,B2(0D%)=-6("!=@0
F(0 2DB*3=.G\.^(4123%(0N)(*<M,&("8%&!+*#$%&9#%

16
!'39@1*&?.D?"!+*#$%&9#%/D%)=-6("%06(&9()8K3!'(3*:G32N
'/?!+*#$%&9#%<F,1"6" 123*39/D*3-/&!9#$%D%)=-6("!*.$9!'(3G32N
M.A"&("
!0ODM.A"&("8"(D!2Z)D,-0B())('/?&(" F*#%%NB)*KL'/?0ODG@$
+2,(0+2O&)/"!=9%
!F2@)!2@$0&)(*!'(3<"-/=DNG@$+NK=&=/0-6(9@73B:Y6%"%0:6 F*#%=.$&
%#$"b G@$%('!B_"=(!F7N<F,D%)=-6("7.D8/DF*#%F/)
>)8@()8N785>A)
+E,)7%%&7:(:
!7*-'=%?<F,1"6<'-6(CD,B[D=-.7ML!+*#$%&9#%123T%DB2/U)%%)
)6%"G;()(*7*-'=%?F*#%?;(*N&*/)J(
!%06(<M,"A;(9/"!M#A%!42.& !?"Y." G."!"%*L 1%2)%d%2LF*#%-/=DN
B*3!^G!D@0-)/" !4*(3%('G;(<F,!+*#$%&9#%9@=@Y@D'(& R.D*:BG*&
F*#%17)F/)CD,
%)*A9$78H.I9*-F)*(;0.
T%D1B*&+(*L?%"%%)9(7*-'=%?!B_"B*3';( !B2@$0"1B*&
+(*L?%"!9#$%=O)F*%'"TO&8@D';()/D */)J(1B*&+(*L?%"<F,=3%(D
123%06(<F,1B*&+(*L?%"F2ND!8,(CB<"G@$0OD +-*!B2@$0"1B*&
+(*L?%"G/A&=%&1B*&4*,%9)/" <M,1B*&+(*L?%"G@$);(F"D!G6("/A"
(92;>?/ 6)
<M,C8+-&!4#$%T%DV(B[DG@$0OD1B*&%%) ";(1B*&+(*L?%"G@$=O)F*%
%%)9( <=61B*&+(*L?%"<F96!8,(CB 123B[DV(B[DG@60OD1B*&<F,1"6"
(92;>?/ 7)
!4#$%+-(9B2%D^/0123+-(9"6(!M#$%T#%8%&R2.7^/KeL+-*<F,H:"0L
?*.)(*G@$R6(")(**/?*%&'() Makita !B_"R:,D;(!".")(*Y6%91Y9
?;(*N&*/)J( 123G;()(*B*/?7/A&%#$"b "%)'()"@A<F,<M,%3CF268%&1G,
'() Makita !=9%

17

18

19

Makita Corporation
Anjo, Aichi, Japan
883234-375 www.makita.com
TRD