Manhattan Comfort 1GMCF User manual

ASSEMBLY HANDBOOK-
FORTRESS 74.8" TALL
GARAGE CABINET
View our assembly video online
www.manhattancomfort.com
Stuck? Questions? We are here to help.
1-888-230-2225
[email protected]
1000008413 -15/03/2018
1GMCF

Do not place the parts directly onto the floor.
Use a cardboard sheet or a mat to place the
parts, during the separation and assembly.
In order to ease the assembly,
you should separate and identify the parts first
Necessary hardware for the assembly, leveling and safety
Stuck? Questions? We are here to help.
1-888-230-2225
[email protected]
View our assembly video online
www.manhattancomfort.com
IMPORTANT
In order to avoid severe or even fatal injuries, follow the instructions carefully.
This furniture should be fixed onto the wall, so to avoid possible drops.
Different types of walls demand different types of hardware.
Hardware to fix the furniture to the drywall is included in the kit.
Should your wall be different, please, ask for advice at the hardware store.
* Included in the kit * Not included in the kit
STANLY
½”

ASSEMBLY HANDBOOK TALL CUPBOARD - FORTRESS 74.8"
TALL GARAGE CABINET
Hardware list
F14
1000008297
Qty. 3
F2
1000009499
Qty. 4
F1
1000009500
Qty. 20
F7
1000008301
Qty. 12
F15
1000008280
Qty. 1
F12
1000008373
Qty. 2
F9
1000008368
Qty. 4
F5
1000008616
Qty. 3
F5
1000008616
Qty. 3
lb
Maximum weight
supported by
shelf
WARNING
P21
Left Shelf
3000007282 P20
Right Shelf
3000007281
P7
Bottom
3000007271
P24
Right Door
3000007255
P25
Left Door
3000007260
P16
Wall Fixation Support
3000007235
P11
Central Back
3000007252
P11
Central Back
3000007252
P11
Central Back
3000007252
P8
Upper Back
3000007264
P9
Lower Back
3000007366
P1
Side
3000007251
P1
Side
3000007251
P5
Top
3000007270
55lb
55lb
55lb
55lb
55lb
F13
1000009033
Qty. 1
Qty. 1
F17
1000008285

1 - Fit part P7 inside part P1
1 - Fit part P5 inside part P1
P5
P1
STEP 2
STEP 1
2x
F1
2x
F1
2 - Fit both parts in the frontal side, with
F1
P1
P5
2 - Fit both parts in the frontal side, with
part F1
P7

P1
P1
P5
P7
1 - Turn the cupboard with the back side
upwards
1 - Fit part P1 to part P5 and P7
2 - Fit part P1 to parts P5 and P7 at the frontal
side, with F1
STEP 4
STEP 3
4x
F1
8x
F1
2 - Fit parts P1 to parts P5 and P7 with
F1
180°
180°
P1
P1
P5
P7
P1
P5
P7
P1

STEP 6
STEP 5 1 - Fit part P8 into part P5 and parts P1
2 - Check that all fits are supported over the
bolts
3 - After fitting the parts, screw the bolts until
locked
WARNING
F13
P1
P1
P5
P7
P8
1 - With the end of F13, smash the safety claw, locking part P8 to part P1.
To avoid possible
falls, this safety
claw should be
fixed.
P1
P1
P5
P7
P8
1
2
3
WARNING
Position part P8 on
the P4 side for
mounting the
cabinet.

1 - Fit parts P11 inside parts P1 and P8, as
illustrated here below.
Check that all fits are supported over the
bolts
2 - After fitting the parts, screw the bolts until
locked
STEP 7
P1
P7
P5
P8
1 - Fit part P9 inside parts P1, P11 and P7.
Check that all fits are supported over the
bolts.
2 - After fitting the parts, screw the bolts until
locked
STEP 8
P11
P11
P11
P9
P1
P1
P7
P5
P8
P11
P11
P11
2
1
1
2

12x
F7
STEP 9
STEP 10
4x
F9
1 - To assembly the cabinet with shoe fit the accessory in part P7 as illustrated here
below and turn to screw. To level the height or the cabinet, turn the shoe either
clockwise or counterclockwise to align it.
1- Turn the cupboard so that it will stand in the position of use
2- Fix F7 to parts P1, as shown here below
P1
P1
P1
P1
P7
P5
P5

STEP 11 1 - Fit the lower part P20 in diagonal position to insert it inside the cupboard
2 - Lean part P20 in part P1 and place it over the F7 detailed in the figure here
below
3 - Lower the other side of part P20, leaning it over the left F7
4 - Repeat above steps for all parts P20 and P21
P20
P20
P21
P5
P1
P7
STEP 12 1 - Align part P16 at an approximate height of
72 ½" from the floor
2 - Align the part using a level
3 - Mark the wall using holes of part P16, aided
by a pencil
4 - Withdraw the part
5 - Drill the wall where market on the wall,
with the pencil using a driller with a ½”
(13 mm) drill
72 ½"
½”
P16
T h e c u p b o a r d
m ust b e f i x e d
onto the wall
WARNING
WALL WALL
F7

STEP 14 1 - Align part P16 to the bushings and fix them
with F5
2 - Fix the cupboard to part P16, held to the wall.
Part P8 tab shall be used to this purpose.
3 - Adjust feet
3x
P16
F5
WALL
WALL
P8
P16
3 - Break the bushing's rods
STEP 13 1 - Insert the metal part of the bushing into
the hole until it overcomes the wall.
2 - Pull the bushing driving it against the wall
and then push the plastic ring
until it leans close to the wall
3x
F14
3x
F14
WALL
WALL
WALL
WALL WALL
Plastic ring
WALL
1
WALL
2

1 - To assembly the doors, fit door P24 lower hinge bolt inside the bushing fixed in part P7
2 - Then, pull down the pin of door P24 upper hinge; align the door and release the pin to fit
the bushing fixed in part P5
3 - Repeat the step for part P25
STEP 16
STEP 15
1º
2º
4x
F1
1 - Turn the central hinge tab until it leans onto P1 hinge back part. Align the hinge tab
and P1 holes and fix it with F1
2 - Repeat the step for part P25
P1
P5
P24
P25
P20
P21
P20
P7
P1
P5
P24
P25
P20
P21
P20
P7
P1

2x
F12
STEP 17
4x
F2
1 - Fit F12 to the inside of part P25, with F2
2 - Adjusting the position of the locking tongue
2
1
P1
P5
P25
P24
P20
P21
P20
P7
1 -Insert product log
F17
1x
STEP 18