Manrose Thin Dry FAN7418 User manual
INSTALLATION INSTRUCTIONS
Thin Dry Hand Dryer
Supply: 220 – 240V AC
Total Power: 1000 W
Air Speed: 100 m/s
Dry Time: 10-12 sec
Housing: Stainless Steel 304
Auto Shut Off: 60 sec
Sound Level: 74 dB(A)
Safety: Class I
IP Rating: IP23
IK Rating: IK08
Dimensions (A x B x C): 174 x 256 x 102 mm
Net Weight: 2.5 kg
FAN7418 - White
FAN7419 - Black
FAN7420 - Brushed
PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING
THEINSTALLATION
! IMPORTANT
This product is suitable for use only with a supply voltage of 230-240V AC, 50Hz.
All electrical work must be carried out in accordance with local and national electrical codes
as applicable.
We strongly recommend that this device is installed by a registered electrician.
Always switch power off prior to installation. A means of mains power isolation must be installed
in the circuit for the purpose of safe access for any internal cleaning, recalibration, or maintenance.
This device is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety. Young children
should be supervised to ensure that they do not play with the appliance.
Any changes or modifications made or attempted to this product, without the prior written approval of
the manufacturer, will void any and all stated warranties.
A
B
C
TECHNICAL SPECIFICATIONS
BEFORE INSTALLATION
See mounting template for complete reference to mounting heights and power knockout locations.
Minimum Length: 300mm
220-240V: 6A
It is recommended to avoid installation of
dryer near high reflective objects (mirror,
stainless steel washbasins, etc.) in order to
avoid errant function of the presence sensor.
INSTALLATION
1 2
3
Be sure to break the electric supply before
any operation.
Remove transport screw at the rear of the dryer. Unscrew front cover from the base of the unit
using the hex key provided.
Using the mounting template supplied,
mark mounting hole locations for correct height
above the floor and drill 4x mounting holes.
45
6
7
Before replacing cover, there is a customised
option to run the dryer heater on (1000 W)
or heater off (600 W).
The switch is clearly marked.
Re-attach the cover to the base of the unit using
the hex key provided. Reconnect power supply
and test operation.
Fix base to the wall. Connect supply and ground wires to terminal
block where indicated.
MAINTENANCE
WARRANTY
This product is guaranteed by Simx Ltd for 5 years from the date of purchase against faulty materials
or workmanship which affects its design ability to switch and operate. During this period if the product
has a defect of this nature it will be repaired or replaced free of charge by Simx with the same item,
or a similar one of higher specifications, ON THE CONDITIONS THAT:
The buyer returns it to the seller from whom it was bought, freight paid.
The product has been bought by the user, i.e. a receipt/sales invoice is produced as a proof of purchase.
The product has not been misused or handled carelessly, installed in anyway contrary to the installation
instruction, or installed in any unusually exposed or harsh environmental conditions.
This guarantee excludes liability for any discolouration or delamination of paint or plastic, or any user
replacement parts. It does not confer any rights other than those expressly set out above and does not
cover any claims for consequential loss or damage.
Our Goods come with guarantees that cannot be excluded under the Australian and New Zealand
Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have the Goods repaired or
replaced if the Goods fail to be of acceptable quality and the failure does not amount to a major failure.
PUB1728 2303
Distributed by Simx (NZ) and Ventair (AUS)
PO Box 14 347, Panmure, Auckland, NZ. Technical Support (09) 259 1662
Specifications are subject to change without notice.
Periodic cleaning of this unit is required to maintain optimum performance and reduce unnecessary
wear on parts. Depending on usage, a regular maintenance programme with a frequency between
3-6 months is highly recommended.
Detach the cover from the dryer and remove any dust or lint. Remove and discard the existing filter
(the HEPA filter cannot be cleaned and reused). Replace with a new HEPA filter and reassemble
after cleaning.
Wipe the cover with a damp cloth and mild cleaning solution. Do not soak.
Never use abrasives to clean the cover.
This manual suits for next models
2
