Sealey IR2000S User manual

PANEL DRYER, INFRARED, SHORT WAVE, 2100W
MODEL NO: IR2000S
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURYAND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instruction
manual
IR2000S Issue:3 12/06/23
Original Language Version
© Jack Sealey Limited
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all
electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey stockist.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance
Test) tested.
Electrical safety information: it is important that the following information is read and understood.
1.1.1. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is tted with the correct
fuse - see fuse rating in these instructions.
8DO NOT pull or carry the appliance by the power cable.
8DO NOT pull the plug from the socket by the cable.
8DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or
replaced immediately by a qualied electrician.
1.1.4. This product is tted with a BS1363/A 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Ensure that repairs are carried out by a qualied electrician.
Replace a damaged plug with a BS1363/A 3 pin plug. If in doubt contact a qualied electrician.
A) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.
B) Connect the BROWN live wire to the live terminal ‘L’.
C) Connect the BLUE neutral wire to the neutral terminal ‘N’.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
Sealey recommend that repairs are carried out by a qualied electrician.
1.2. GENERAL SAFETY
WARNING! If a fuse blows, ensure it is replaced with a fuse of identical type and rating.
WARNING! Ensure there is nobody in front of the lamp when it is switched on.
9Disconnect the panel dryer from the power supply before servicing, changing accessories, or performing any maintenance.
9Ensure that the panel dryer is in good condition before use. If in any doubt do not use the unit and contact an electrician.
9When not in use, store the panel dryer carefully in a safe, dry, childproof location.
9Familiarise yourself with the application and limitations of the panel dryer.
9Check that lamp guards are in place, undamaged and firmly attached.
9Keep tools and other items away from the panel dryer when it is in use.
9Keep the work area clean and clear of unnecessary items.
9Keep children and unauthorised persons away from the work area.
9Remember that the lamp panel will get hot, allow to cool after use.
9Maintain the panel dryer in good condition. Use authorised agent for servicing.
9Keep the dryer clean, but DO NOT use solvents.
9Use only genuine parts and accessories. Unauthorised parts and accessories may be dangerous and will invalidate your warranty.
8DO NOT use this product to perform a task for which it has not been designed.
8DO NOT use the panel dryer outdoors, or in damp, or wet locations, and DO NOT operate within the vicinity of flammable liquids, gases or
solids.
2. 
Designed and developed to assist with any number of small drying processes. Ideal for spot repairs, engine drying, adhesive stripe
removal, drying ller, drying primer or just preheating prior to spraying. Supplied with a sturdy 1500mm plated steel stand and a 3.7m
power cable and 3-pin plug.
Replacement fuse
rating:13A
Warning:
Electricity Warning:
Hot Surface Indoor
Use Only Do Not Cover

Original Language Version
© Jack Sealey Limited
3. SPECIFICATION
Model No: IR2000S
Element Power: 2100W
Fuse Rating: 13A
Plug Type: 3-Pin BS
Power Supply Cable Length: 3.7m
Reector Size: 530 x 140mm
4. ASSEMBLY
4.1.  
4.1.1. Take out two parts of the post, peel o󰀨 the sticker and
insert the upper section (g.1.3) into the lower
section (g.1.2) as indicated by the arrow direction (g.1).
4.1.2. Take out the pedestal (g.1.1), insert the mounting post into
the pedestal properly, and securely tighten the screws.
4.1.3. Fix the locking hoop (g.1.4) onto the post, placing the lamp
cassette to the front, and then tighten the handle.
NOTE: Ensure that all xings are securely located and the
unit is stable.
4.2.  
4.2.1. Assemble lamp arrangement using the adjustment handle,
spring washer and plain washers (g.2.C) in seven
positions shown.
4.2.2. Assemble post mounting section using adjustment handle,
spring washer and plain washers in position shown (g.2.F).
fig.1
Model No: IR2000S
No. of Elements: 2 x 1050W
Optimal Baking Area: 0.6m x 0.8m
Operating Temperature (°C): 60-70°C
Timer Range: 0-30min
Supply: 230V ~50Hz
Item
no. Description Item No. Description
1 Front castor wheel 11 Emitter tube
2 Back castor wheel 12 Front protective net
3 Pedestal 13 Control Panel
4 Post 14 AM12 adjustable handle
5 Side panel of emitter 15 Small reective panel
6 Connectors (left and right) 16 Rear panel
7Control box 17 Ceramic connector
8 U shape support 18 Reective panel
9 AM8 adjustable handle 19 Timer
10 Bent plate
1
2
34
fig.2
B
ADE F
C
IR2000S Issue:3 12/06/23

Original Language Version
© Jack Sealey Limited
4.3.  
4.3.1. When adjusting the height of lamp unit, use your left hand to support the
U-shaped support and use your right hand to loosen the locking handle,
and then move the lamp unit with your two hands supporting the two ends of the
lamp unit. DO NOT try to adjust by using one hand this will avoid causing any
damage to the tube caused by lamp unit falling.
5. OPERATION
5.1.   
5.1.1. Place the panel dryer in the required area and lock the caster wheels.
5.1.2. Turn the temperature to the required setting.
5.1.3. Switch on either switch A or B power switches or both depending on job
requirement.
5.1.4. Now turn the baking timer control to the required time for the job. The
switches on A and or B will light and commence to illuminate the lights
selected.
5.1.5. When the time has expired the unit will automatically turn o󰀨. If longer time
required just re-adjust the baking timer control and the job can be continued.
6. MAINTENANCE
WARNING! Disconnect from the mains before carrying out any maintenance.
WARNING! Never touch the element glass directly with ngers, only touch
the ceramic ends or use a soft cloth, otherwise the tube may get damaged.
6.1.  E (g.3)
6.1.1. Check power switches are in the o󰀨
position and is disconnected from the
mains supply.
6.1.2. Take out the front protective grill in front of
the emitter.
6.1.3. Loosen the screws on the side panel
of the emitter and remove the side panel.
6.1.4. Release rear panel.
6.1.5. Loosen the two leads in the lamp tube
and remove the tube.
6.1.6. Fix the new tube with same model
number and wire the tube correctly.
6.1.7. Install the rear panel reective panel and
the side panel.
6.1.8. Use a piece of soft cloth or cotton to
clean the reective panel and the tube
with alcohol.
6.1.9. Install the front protective grill.
7. 
7.1. Causes of defects on repaired surface and troubleshooting method.
NOTE: For optimal baking performance, we recommend that users should work out the suitable operating procedures, baking time and
distance according to the local natural conditions, working environment and the types of paints.
fig.3
Baking timer
Control
Temperature
adjustment
Power switch
fig.3
DEFECT C T
Small pores on the baked
paint surface. Too near between the lamp cassette and the repaired surface. Increase the distance.
Insu󰀩cient Preheating time. Increase the preheating time.
Fast thinning agent included in the paint. Use standard or slow thinning agent.
Dim paint. Too far between the emitter and the repaired
surface. Make the machine closer.
Insu󰀩cient baking. Increase the baking time
Too thick coating. Thin the coating.
Stains. Too long baking. Shorten the baking.
Too near distance. Increase the distance.
Fuzzy edge. The repair surface is too large. Preheating for rst time, and do not
use preheating for second time.
Uneven baking. The emitter is not at same height as the
repaired surface. Adjust the emitter to allow it to be at height as the repaired surface.
IR2000S Issue:3 12/06/23

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste.All tools, accessories and packaging should be sorted,
taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product
becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and
dispose of the product and fluids according to local regulations.

Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
REGISTER YOUR
PURCHASE HERE
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on [e-mail] or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Original Language Version
© Jack Sealey Limited IR2000S Issue:3 12/06/23