Marantz SA-11S1 User manual

Model SA-11S1 User Guide
Super Audio CD Player
CLASS 1 LASER PRODUCT
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of suffi-
cient magnitude to constitute a risk of electric shock
to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS
LA BORNE CORRESPON-DANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
LASER SAFETY
This unit employs a laser. Only a qualified service person should remove
the cover or attempt to service this device, due to possible eye injury.
CAUTION : USE OF CONTROLS OR ADJUSTMENTS
OR PERFORMANCE OF PROCEDURE
OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals

IMPORTANT SAFETY
INSTRUCTIONS
READ BEFORE OPERATING EQUIPMENT
This product was designed and manufactured to meet strict quality and safety standards. There
are, however, some installation and operation precautions which you should be particularly aware
of.
1. Read these instructions - All the safety and operating instructions should be read before the
product is operated.
2. Keep these instructions - The safety and operating instructions should be kept for future
reference.
3. Heed all warnings - All warnings on the product and in the operating instructions should be
adhered to.
4. Follow all instructions - All operating and use instructions should be followed.
5. Do not use this apparatus near water - Do not use this product near water-for example, near a
bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool,
and the like.
6. Clean only with dry cloth - Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a dry cloth for cleaning.
7. Do not block any ventilation openings. Install in accordance with the manufacture's
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
AC GROUNDING-TYPE PLUG
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals

13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
15. This product should not be placed in a built-in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer's instructions have been adhered to.
16. To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the
apparatus.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe B est conforme àla norme NMB-003 du Canada.
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals

EXAMPLE OF ANTENNA GROUNDING ACCORDING TO
NATIONAL ELECTRICAL CODE INSTRUCYIONS
CONTAINED IN ARTICLE 810 -"RADIO AND TELEVISION EQUIPMENT"
GROUND CLAMP
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA LEAD
IN WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC - NATIONAL ELECTRICAL CODE
This Class B digital apparatus complies
with Canadian ICES-003.
Cet appareil numérique de la Classe B est
conforme ála norme NMB-003 du Canada.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment gen-
erates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of
the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and
receiver.
–Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV tech-
nician for help.
NOTE:Changes or modifications may cause this unit
to fail to comply with Part 15 of the FCC Rules and may
void the user's authority to operate the equipment.
NOTE TO CATV SYSTEM INSTALLER:
This reminder is provided to call the CATV (Cable-TV) system installer's attention to Article 820-40 of the NEC,
which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point of cable entry as practical.
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals

ENGLISH
1
CONTENTS
INTRODUCTION ................................................................................................................................... 2
PRODUCT FEATURES .......................................................................................................................................3
ABOUT SUPER AUDIO ......................................................................................................................................3
PLAYING CD-RW DISCS.................................................................................................................................... 3
APPLICABLE DISCS TO THE UNIT ...................................................................................................................3
BEFORE USING .................................................................................................................................... 4
NOTES ABOUT THE DISCS .............................................................................................................................. 4
INAPPROPRIATE PLACES FOR INSTALLATION .............................................................................................. 4
PRECAUTIONS ..................................................................................................................................................5
USING REMOTE CONTROL UNIT.....................................................................................................................5
LOADING BATTERIES .......................................................................................................................................5
NAMES AND FUNCTIONS .................................................................................................................... 6
FRONT PANEL ...................................................................................................................................................6
REMOTE CONTROLLER ................................................................................................................................... 7
REAR PANEL ..................................................................................................................................................... 9
DISPLAY ........................................................................................................................................................... 10
CONNECTIONS .................................................................................................................................. 11
OPERATION ........................................................................................................................................ 12
CONNECTING THE POWER SUPPLY .............................................................................................................12
NORMAL PLAYBACK .......................................................................................................................................12
START SOUND MODE .....................................................................................................................................13
MAKING YOUR FAVORITE AUDIO SETTINGS ................................................................................................14
PLAYING YOUR FAVORITE TRACKS OF A DISC ........................................................................................... 16
PLAYING YOUR FAVORITE PARTS OF A DISC (SEARCH) ............................................................................16
REPEATED DISC PLAY (REPEAT PLAY) ........................................................................................................16
PLAYING TRACKS IN A RANDOM SEQUENCE (RANDOM PLAY) ................................................................ 17
PLAYING TRACKS IN A SPECIFIC SEQUENCE (PROGRAM PLAY) .............................................................17
SEARCHING YOUR FAVORITE TRACKS (AMS (AUTOMATIC MUSIC SCAN) PLAY) .................................... 18
QUICK REPLAY ................................................................................................................................................19
ABOUT THE TEXT INFORMATION DISPLAY .................................................................................................. 19
CHANGING THE TEXT BRIGHTNESS ON THE LCD (LCD CONTRAST ADJUSTMENT) ............................. 20
TURNING OFF THE DISPLAY AND ILLUMINATION (DISPLAY OPERATION) ............................................... 20
TIMER PLAY ..................................................................................................................................................... 21
ABOUT BALANCED JACKS .............................................................................................................................21
TROUBLE SHOOTING ........................................................................................................................ 22
SPECIFICATIONS
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals

ENGLISH
2
Thank you for selecting the Marantz SA-11S1 Super Audio
CD Player for your Audio system.
This Player incorporates a number of features designed to
enhance the listening of your favorite audio sources.
Please read these operating instructions carefully. We
recommend that you read the entire user guide before you
attempt to connect or operate the player.
After you have reviewed the contents of this manual,we suggest
that you make all system connections before you attempt to
operate the unit.
INTRODUCTION
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals

ENGLISH
3
APPLICABLE DISCS TO THE UNIT
1. Super Audio CD
There are three types of Super Audio CDs.
•Single-layer Disc
•Dual-layer Disc
•Hybrid-layer Disc
And each type may contain two areas of recorded information.
•High quality stereo area
•High quality multi-channel area**
•Single Layer Disc
It can contain both high quality stereo area and high quality
multi-channel area** information.
•Dual Layer Disc
It can contain both high quality stereo area and high quality
multi-channel area** information. And a double amount of
information can be stored on the disc thanks to the second
layer.
•Hybrid Layer Disc
Not only does this disc contain both high sound quality
stereo area and high sound quality multi-channel area**
information, it also has a CD layer in the second layer, so it
can be played on a CD player.
The number of tracks recorded may vary per layer. It will be
shown on the display window of the unit.
** This unit is a stereo-only player, and so it cannot play
high-quality multi-channel audio areas. (It does not
recognize multi-channel areas.)
2. Audio CD (CDDA)
Audio CDs contain music tracks only.
PRODUCT FEATURES
This unit can playback the outstanding sound performance in
Super Audio CD. This unit has the following unique features.
• Low-noise low-distortion filter circuit and high-speed
current-feedback-type output amplifier with the differential
input type HDAM.
• Text information display function that can display disc titles,
track titles etc. in Super Audio CD.
• CD-R/CD-RW discs can be played.
ABOUT SUPER AUDIO
The Super Audio standard is based on Direct Stream Digital
(DSD) technology. This new direct-stream digital format
comprises a 1-bit system that has a digital sampling frequency
that is 64 times higher than that of conventional audio CD. The
results are spectacular: a frequency response of over 100k
Hz and a 120 dB dynamic range over the entire audible
spectrum. Mixed with as many of the original frequencies as
possible, the audio information audible for human ears sounds
much more natural.
All audible frequencies are, after all, embedded in the frequency
range as emitted by the sound source. A better reproduction
does not exist! For the first time your ears will relive reality.
PLAYING CD-RW DISCS
This unit can play back the CD-RW (ReWritable) discs as well
as ordinary Audio CD and CD-R (Recordable) discs.
• The CD-R and CD-RW discs should contain properly-
recorded TOC information so that they can be played back.
In CD recorders, the task of writing TOC information is
referred to as finalizing the disc. Discs that are not finalized
cannot be properly recognized as an Audio CD and played
back by regular CD players and Super Audio CD players.
For details, please read the instruction manual provided
with a CD recorder.
* TOC stands for Table Of Contents and contains
information such as the total number of tracks and total
playing time of the disc.
• This unit can play only the discs recorded in the CD-DA
format designed for music reproduction. Do not attempt to
play a disc containing other data, such as a CD-ROM for
PCs, on this unit.
• As the playback of a CD-RW disc necessitates partial
change of the player setup, it may take longer time for
reading the TOC information than when an Audio CD or
CD-R disc is played.
INTRODUCTION
Disc Types
Single-layer Disc
Dual-layer Disc Hybrid-layer Disc
HD layer HD layer CD layer HD layer
Hybrid Super Audio CD Disc
1CD layer that plays on any of your
existing CD players
High-Density layer containing:
2- High sound quality stereo
3-
High sound quality multi-channel **
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals

ENGLISH
4
NOTES ABOUT THE DISCS
* Handle the discs carefully so as not to scratch their
surfaces.
* Keep the surfaces of the discs clean at all times.
When cleaning the surfaces of discs, always be sure to use
the special cleaner and wipe the surfaces in the directions
shown in the figure below.
* Do not attach pieces of paper or stickers to the label
surfaces of the discs.
When a disc has a piece of plastic tape or rental CD label
with paste protruding from the edge or when a disc still bears
traces of sticky tape or adhesive labels, do not attempt to
play it. If such a disc is played on the CD player, you may
find that you cannot remove it or that some other kind of
malfunctioning may occur.
* Do not use discs which come in special shapes.
Do not attempt to play heart-shaped or octagonal discs or
discs with any other special shapes. You may find that you
cannot remove them or that some other kind of malfunctioning
may occur in the player.
* Use discs which satisfy the CD standards such as those
with the “CD logo” or “ ” mark on their disc label
surfaces.
No guarantees are made for playback if discs which do not
satisfy the appropriate CD standards are used.
Similarly, no guarantees are made for their sound quality even
if it is possible to play such discs.
* To protect your discs from damage, avoid placing them
in the following locations.
•Where they will be exposed to direct sunlight or where they
will be close to a heater or other heat-radiating appliance
•Where the humidity level is high or it is very dusty
•Near a window or other such location where they may be
exposed to rain
* Get into the habit of putting the discs back in their cases
after use.
BEFORE USING
•Wipe the surface radially
from the center.
•Do not wipe the surface in
the circumferential direction.
PAUSE
STOP
PLAY
OPEN/
SOUND
POWER ON/OFF
SUPERAUDIO CD PLAYER SA-11S1
CLOSE
MODE
DISPLAYOFF
0.1 m or more 0.1 m or more
0.1 m or more
0.1 m or more
INAPPROPRIATE PLACES FOR
INSTALLATION
To keep your player in perfect working order for the longest
possible time, avoid installing the player in the following
locations.
•Wherever it will be exposed to direct sunlight
•Wherever it will be close to a heater or other heat-radiating
appliance
•Wherever the humidity is high or ventilation is poor
•Wherever it is very dusty
•Wherever it will be subject to vibration
•On top of a rickety stand or in an unstable location which is
tilted at an angle
•In an audio rack with little space at the top and bottom or
other location where the heat dissipation will be obstructed
To ensure proper heat dissipation, install the player while
leaving clearances between the player and wall or other
components, as shown in the figure below.
•On top of an amplifier or other component which dissipates
a great deal of heat
* The quality of the laser and other components can be
harmed if the player is placed directly on top of an
amplifier or other device which generates heat.
7 Do not place objects on top
•Refrain from placing any objects on top of the player.
7Cautions on handling power cord
•Do not touch the power cord with wet hands.
•When disconnecting the power cord, always make sure
that you take hold of the plug. Yanking out or bending the
cord can damage it and/or cause electric shocks or a fire.
•Get into the habit of disconnecting the power plug before
leaving home.
7Do not attempt repairs yourself
•Refrain from lubricating the player: doing so can cause
malfunctioning.
•Only qualified engineers with specialized expertise are
authorized to repair the pick-up and parts inside the player.
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals

ENGLISH
5
USING REMOTE CONTROL UNIT
Cautions on handling batteries
Misuse of the batteries can result in electrolyte leakage,
rupturing, corrosion, etc.
Bear in mind the following points when using batteries.
•Remove the batteries from the remote control unit if
the unit is not going to be used for a prolonged period
(a month or more).
•Do not use an old battery together with a new one.
•Insert the batteries while ensuring that their and
poles are properly aligned with the corresponding
markings on the remote control unit.
•Batteries with the same shape may have different
voltages. Do not use different types of batteries
together.
•If electrolyte has leaked, thoroughly wipe the inside
of the battery compartment, and then insert new
batteries.
•When batteries which are no longer required are to
be discarded, follow the directions (regulations) laid
down by the local authorities in the area concerned
for their disposal.
PRECAUTIONS
•In winter, droplets of water form on the insides of the
windows of a heated room: this is called condensation. This
player uses an optical lens, so the condensation may form
in the following cases.
- In a room immediately after the heating has been turned
on
- In a room where the humidity level is high
- When the player has been suddenly brought from a cold
location into a warm room
Since, in cases like this, the track numbers may not be
read and the player is prevented from operating properly,
wait about 30 minutes, and then operate the player.
•This player may cause interference on a tuner or TV set. If
this is the case, place it further away from the tuner or TV
set.
•Compact discs have much less noise than analog records
and hardly any noise is heard before play starts. Bear in
mind, therefore, that if the volume control on the amplifier
is set too high, you will risk damaging other audio
components.
•This player is designed to play Super Audio CD and normal
Audio CDs only. It cannot play CD-ROMs used with
personal computers, game CDs, video CDs or DVDs (video/
audio).
•We do not recommend the use of lens cleaners.
LOADING BATTERIES
Batteries in this remote control unit have a life of approximately
1 year under normal operating conditions. If the remote control
unit is not going to be used for an extended period of time,
remove the batteries. Also, if you notice that the batteries are
starting to run down, replace them as soon as possible.
qRemove the battery cover.
wInsert the batteries with correct +/–orientation.
eClose the battery cover until it clicks shut.
7Remote control
Operate the remote control unit (RC-11SAS1) within a distance
of approx. 5 m from the infrared signal reception window
(remote sensor) on the front of the Super Audio CD player.
Remote control operation may not be possible if the remote
control unit’s transmitter is not pointing in the direction of the
remote sensor or if there is an obstruction between the
transmitter and the remote sensor.
Remote control operating range
Remote control unit (RC-11SAS1)
Approx. 5m
60°
BEFORE USING
Two AAA-size (R03) batteries
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals

ENGLISH
6
FRONT PANEL
zPOWER ON/OFF switch
This switch is used to turn the power ON and OFF. When
it is pressed, the display window lights up, and the power
comes on. When it is pressed again, the display window is
extinguished, and the power goes off.
xDisc tray
The disc to be played is placed on the tray.
* Close the tray by pressing the operation button, not by
pressing it in with your hand.
cRemote sensor
The infrared control signal emitted from the remote control
unit are sensed here.
vLCD
This screen shows the operating status.
b
SOUND MODE
button
Press this button to select the Super Audio CD sound mode.
Super Audio CD (stereo) or Audio CD (if discs are sup-
ported) (See page 13)
n, (Track Skip/Search buttons)
These buttons can be used as both track skip and track
search buttons. (The buttons on the main unit only.)
: Each time this button is pressed, the track being
played is skipped forward. When this button is
held down, tracks are searched forward (Fast
Forward).
: When this button is pressed, the unit goes back
to the beginning of the current track. If the button
is pressed more times, the track being played
is skipped back.When this button is held down,
tracks are searched backward (Fast Rewind).
In program play, Fast Forward and Fast Rewind can be
done in the playing track only.
m
PAUSE
button
Press this button to pause playback. If pressed again, the
unit returns to playback.
Holding down this button for two or more seconds while a
track is stopped starts LCD Contrast Adjustment mode.
(See page 20)
,
STOP
button
Press this button to stop playback. Also this button is used
to clear all programs.
.
PLAY
button
Press this button to start playback.
⁄0
OPEN/CLOSE
button
Press this button to open the tray. Put on a disk label side
up. Press the button again to close the tray.
⁄1 DISPLAY OFF indicator
This indicator turns on when the LCD screen is turned off
(Off mode).
⁄2 Illumination lamp
This lamp lights when the display window lights.
This lamp may always remain off for certain settings. (See
page 20)
PAUSE
STOP
PLAY
DISPLAY OFF
OPEN/
SOUND
POWER ON/OFF
SUPER AUDIO CD PLAYER SA-11S1
CLOSE
MODE
bÚ1 c zxv mnÚ0Ú2 , .
NAMES AND FUNCTIONS
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals

ENGLISH
7
b
SOUND MODE
button
m
PAUSE
button
,
STOP
button
.
PLAY
button
⁄0
OPEN/CLOSE
button
The buttons listed above are the same to the buttons on the
front panel of the main unit.
Please see the correspond items in “Front Panel”section.
REMOTE CONTROLLER ⁄3
TIME
button
This button is used to switch from the text display to the
time display when using a text-compatible Super Audio CD.
It is also used to change the time display. Each time that it
is pressed, the displayed time cycles from track elapsed
time →track remaining time →total remaining time →
track elapsed time . (See page 13)
⁄4
TEXT
button
This button is pressed to switch the main screen from the
time display to the text display when using a text-compat-
ible Super Audio CD. (See page 19)
⁄5
DISPLAY
button
This button switches the display screen on and off.
The ⁄1 indicator turns on when Display Off is set. (See
page 20)
⁄6
0
-
9
(Numerical buttons)
Use these buttons to select tracks directory.
⁄7
PROG.
button
This button is for program play. (See page 17)
⁄8 , (Track skip buttons)
: When this button is pressed, the unit goes back to
the beginning of the current track. If the button is
pressed more times, the track being played is
skipped back.
: Each time this button is pressed, the track being
played is skipped forward.
* Search buttons are provided separately for the remote
control unit. Use ⁄9 Search buttons for search function.
⁄9 , (Search buttons)
: While this button is pressed during playback, tracks
are searched backward.
: While this button is pressed during playback, tracks
are searched forward.
¤0
RECALL/SCROLL
button
Use this button to scroll text while displaying text informa-
tion in a Super Audio CD disc that supports TEXT.
This button is also used for checking the programmed tracks
during a program or when a program is stopped. (See page
18)
* In this instruction manual, some operations can only be performed with the remote control. For operations that can be
performed with buttons both on the main unit and on the remote control, the button names are shown in the mark.
And for operations that can only be performed with buttons on the remote control, the button names are shown in the
mark.
CANCEL
A-B
SOUND
INPUT
QUICK
VOLUME
OPEN/
RECALL
NOISE
RC-11SAS1
MODECLOSE
DISPLAY TIME TEXT
MENU SCROLLENTER
AMP
REPLAY
AMS
PROG
RANDOM
REPEAT
4
123
56
789
0
DIGITAL OUT
DC FILTERSHAPER FILTER
⁄3
⁄0
⁄5
¤6
‹2
m
.
⁄8
,
⁄9
¤2
¤4
¤1
⁄7
¤8
⁄6
¤9 ‹1
‹0
¤3
¤5
¤7
‹3
¤0
⁄4
b
NAMES AND FUNCTIONS
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals

ENGLISH
8
¤1
CANCEL
button
Use this button to cancel a programmed track. (See page
18)
¤2
A-B
(A-B Repeat button)
This button is to determine starting and ending points for
A-B repeat play. (See page 16)
¤3
RANDOM
button
This button is for random play. (See page 17)
¤4
AMS
(Automatic Music Scan button)
Use this button for AMS play. (See page 18)
¤5
REPEAT
button
This button is for repeat play. Each time this button is
pressed, repeat mode changes as follows. “All Repeat”→
“Track Repeat”→“Repeat Off”(See page 16)
¤6
MENU
button and
ENTER
button (Menu
setup)
These buttons are used to set the time for quick replay.
(See page 19)
¤7
QUICK REPLAY
(Quick replay) button
This button is used to do quick replay of the tracks. (See
page 19)
¤8
NOISE SHAPER
button
This button is pressed to turn the noise shaper on and off.
(See page 14)
¤9
DC FILTER
button
This button is pressed to turn the DC filter on and off. (See
page 14)
‹0
FILTER
button
This button is pressed to make the digital filter settings.
Each time it is pressed, the settings cycle from FIL1 →
FIL2 →FIL3 →FIL1. (See page 15)
‹1
DIGITAL OUT
button
This button is pressed to turn the digital output for the Au-
dio CD signal on and off. (See page 14)
‹2
INPUT
button
This button switches the input selector (INPUT) of the
Marantz PM-11S1 amplifier.
‹3
VOLUME
button
This button is used to increase or decrease the volume of
the Marantz PM-11S1 amplifier.
NAMES AND FUNCTIONS
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals

ENGLISH
9
REAR PANEL
A ANALOG OUTPUTS UNBALANCED connectors
These are the unbalanced output jacks of the analog au-
dio signals. The supplied analog connection cord can be
connected to the CD, AUX, or other connectors on an
amplifier. Be sure to connect the L and R channels cor-
rectly to the corresponding jacks.
* Never connect to the PHONO connector on the amplifier.
BANALOG OUTPUTS BALANCED connectors
These are the balanced output jacks of the analog audio
signals. A balanced connection cord (available commer-
cially) can be connected to the balanced input jack of the
amplifier. Be sure to connect the L and R channels cor-
rectly to the corresponding jack. (See page 21)
* If connecting the balanced output jacks, be sure to leave
the unbalanced jacks unconnected. (The balanced and
unbalanced connectors cannot be used at the same time.)
CDIGITAL AUDIO OUT COAX.
It outputs the playing Audio CD signal in digital format. This
jack is to be connected with a recording device, amplifier,
D/A converter, etc that has coaxial digital input using an
optional coaxial digital cable.
* Nothing is output when digital output is set to off.
* No signal will be output when a Super Audio CD is played.
DDIGITAL AUDIO OUT OPT.
It outputs the playing Audio CD signal in digital format. This
jack is to be connected with a recording device, amplifier,
D/A converter, etc that has optical digital input using an
optional square type optical digital cable.
* Nothing is output when digital output is set to off.
* No signal will be output when a Super Audio CD is played.
EREMOTE CONTROL IN, OUT (input and out-
put) connectors
When the remote control connectors on the player and on
a Marantz AV component are connected using the acces-
sory remote control connecting cables, the components
can be operated as a system by remote control.
•When connecting to a component which is equipped
with remote control connectors, the player’s REMOTE
CONTROL IN connector must always be connected to
the REMOTE CONTROL OUT connector on the other
component to be connected.
•When connecting a component which is not equipped
with an infrared remote sensor, this component must
always be connected to the player’s REMOTE CON-
TROL OUT connector.
FEXT./INT. (Ext./Internal switch)
When this unit is used as a standalone component, set
this switch to the INT. side. When it is used connected to
external component by a remote connecting cable and to
audio component with a remote sensor that supports re-
mote controls by Maranz, set this switch to the EXT. side.
* If the unit is used as standalone and the switch is set
to EXT. position, remote control unit cannot be used.
GAC POWER INPUT JACK
Connect the supplied power cord to this jack and a house-
hold AC power outlet.
AB CDEFG
NAMES AND FUNCTIONS
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals

ENGLISH
10
DISPLAY
aMain display
The time display and text information of the disc to be played
as well as the setting menus and other displays appear on
the main display.
b1-20, (music calendar)
The number of tracks recorded on the disc to be played,
the number of remaining tracks to be played, and the num-
ber of tracks programmed by program play appear here.
“”light when 21 or more tracks have been recorded on
the disc.
c33
33
3(play) indicator
This lights during disc play.
d88
88
8(pause) indicator
This lights when play is paused (temporarily stopped).
e, ALL, 1 (repeat) indicator
This lights during repeat play.
fA-B (A-B repeat) indicator
This lights during A-B repeat play.
gTRK (track) indicator
This lights above the display of the track number now play-
ing, for instance.
hPROG (program) indicator
This lights during program play.
iRNDM (random) indicator
This lights during random play.
jAMS (auto music search) indicator
This lights during AMS playback.
kCD, SACD, STEREO Disc indicator
This indicates the type of disc on the disc tray.
lTOTAL (total time) indicator
When the total remaining time or the total program time is
displayed, this lights above the display.
mREMAIN (remaining time) indicator
When the remaining playback time of a track is displayed,
this lights above the display.
nN SHP (noise shaper) indicator
This lights when the noise shaper is turned on. (See page
14)
oFIL 1 2 3 (filter 1, filter 2, filter 3) indicator
This indicates which filter among filter 1, filter 2, or filter 3
is currently selected. (See page 15)
pDCF (DC filter) indicator
This lights when the DC filter is turned on. (See page 14)
qD OFF (digital output off) indicator
This lights when the digital output setting for the CD signal
is set to off. (See page 14)
a b
ced fgh j l m o qpnki
NAMES AND FUNCTIONS
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals

ENGLISH
11
Depending on your amplifier/receiver/Stereo System, there are various ways to connect to this player. For correct connection
please refer to instruction manuals of stereo system to be connected.
Caution: Do not connect output from this unit to PHONO input of your audio system.
1. Connect the audio cable qto this unit’s front speaker outputs and the stereo inputs on your amplifier, receiver or stereo system.
2. Connect the optical cable w, coaxial cable eto the digital input on your AV amplifier, D/A converter, CD-R, etc..
* Signal will be output from the digital audio out jacks (OPT./COAX.) only when an Audio CD disc is played. No signal is output
when playing a Super Audio CD.
INTEGRARED AMPLIFIER PM-11S1
POWER ON/OFF
PHONES
VOLUME
A
TONE
SPEAKER
B
SPEAKER
REC OUT
PRE OUT
ATT.
MC
OPERATE
PHONO
DISPLAY
SELECTOR
INPUT
To Analog Audio output
(white)
(red)
To Digital Audio
output
w
(Optional)
e
(Optional)
Left
speaker
Right
speaker
Audio cable q
(Supplied)
To audio input
terminals on amplifier
Connect to digital input
terminals of receiver, D/A
converter or CD recorder,
etc..
Example)
PM-11S1
To balanced
input
terminals on
amplifier
Balanced
connection cord q
(Optional)
CONNECTIONS
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals

ENGLISH
12
OPERATION
* In this instruction manual, some operations can only be performed with the remote control. For operations that can be
performed with buttons both on the main unit and on the remote control, the button names are shown in the mark.
And for operations that can only be performed with buttons on the remote control, the button names are shown in the
mark.
CONNECTING THE POWER SUPPLY
1Plug the power cable into AC IN jack on the back panel.
2Turn on the power switch of the audio unit (amplifier, etc.)
that is connected with this unit. Set the selector on the
connected unit to this unit.
3Plug the power cable into an AC outlet.
NORMAL PLAYBACK
7Super Audio CD player playback
PAUSE
STOP
PLAY
OPEN/
SOUND
POWER ON/OFF
SUPER AUDIO CD PLAYER SA-11S1
CLOSE
MODE
DISPLAY OFF
qPress POWER switch to turn on.
LCD
The display cycles from TOC Reading →No Disc (when
no disc is loaded) →Super Audio CD (when the start sound
mode setting is Super Audio CD).
wPress the
OPEN/CLOSE
button
The disc tray comes out. Place the disc with label side up
on the tray.
To play a single (8cm) CD, place the disc with the
indentation at the center of the tray.
ePress
OPEN/CLOSE
button.
rPress
PLAY
button.
Disc type is automatically detected and playback is started.
Track number and track elapsed time(minute, second)
appear on the display.
* For Super Audio CD/CD hybrid-layer discs (See page 3),
the layer that is set in the start sound mode (See page
13) is played. To change the layer, use the
SOUND MODE
button. (See page 13)
(Exp.:Track 6, Elapsed time 2 min 8 sec)
Playback automatically stops at the end of the final track.
Number of current track Minutes Seconds
Remaining track numbers
AC IN
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals

ENGLISH
13
To start playback form the first track
Press
PLAY
button.
To stop playback
Press
STOP
button.
To eject disc
Press
OPEN/CLOSE
button to open the disc tray and take the
disc off. Press the button again to close the tray.
Disc tray must be closed when the unit is not be used.
To pause playback
Press
PAUSE
button.
PAUSE indicator will light and playback is paused at the point
that the button is pressed.To restart playback, press
PAUSE
button again or press
PLAY
button.
To change time display
Press the
TIME
button on the remote control.
Each time
TIME
button is pressed, display will change in the
following order. “Track elapsed time”→“Track remaining time”
→“Total remaining time”→“Track elapsed time”.
•Track remaining time
(The remaining playing time from the playing point to
the end of the current track)
•Total remaining time
(The remaining playing time from the playing point to
the end of the last track)
* If
TIME
button is pressed when Super Audio CD disc that
supports text is in use, time display is given priority and the
text information will not be displayed afterward. To see the
text information, press
TEXT
button.
7 Switching Sound Mode (Super Audio
CD)
PAUSE
STOP
PLAY
OPEN/
SOUND
POWER ON/OFF
SUPER AUDIO CD PLAYER SA-11S1
CLOSE
MODE
DISPLAY OFF
qPress
SOUND MODE
button in stop mode (not
playing).
The currently selected layer or area is shown on the LCD.
(CD or Super Audio CD)
If
SOUND MODE
button is pressed again, a playable layer or
area will be shown, and the layer or area will be switched
to new one.
* When layer or area is switched, TOC will be read again.
* The sound mode cannot be changed for Audio CDs and
discs with only a Super Audio CD area.
* The sound mode on hybrid layer discs will be changed in
the following order.
Super Audio CD stereo area →CD layer →Super Audio
CD stereo area
* Sound mode can be selected while the tray is open. Select
a desired layer or area and press
PLAY
button then
the tray will close and playback will be started.
w Press the
SOUND MODE
button during playback.
The currently selected layer or area is shown on the LCD.
(CD or Super Audio CD)
If
SOUND MODE
button is pressed again, the playback is
stopped, and the layer or area will be switched to new one.
When you want to listen at that area, press
PLAY
button
again. The playback will be started.
START SOUND MODE
When a Super Audio CD hybrid layer discs that has both a
Super Audio CD high sound quality stereo area and an Audio
CD area information are to be played, this player makes it
possible to set the layer/area (Super Audio CD or Audio CD)
to be preferentially played.
This setting can be made when the tray is closed and there is
no disc in the disc tray.
qPress
SOUND MODE
button on the player.
The currently selected layer/area is displayed.
If the Super Audio CD is selected : Super Audio CD
If the Audio CD is selected : CD
wPress the
SOUND MODE
button again to display the layer/
area to be played first, and then leave the setting for at
least two seconds to register the setting for the start sound
mode.
Caution
* Start sound mode has a memory retention function where
the settings remain stored and unchanged even when the
disc is changed or the power is turned off.
* At the time of shipment, the sound mode is set to Super
Audio CD.
“–” is displayed “REMAIN”
is displayed
“–” is displayed “TOTAL REMAIN”
is displayed
SOUND MODE
Button
OPERATION
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals

ENGLISH
14
MAKING YOUR FAVORITE
AUDIO SETTINGS
The settings can be made using the remote control (RC-
11SAS1). The settings are retained even if the power is turned
off so that you can always enjoy tracks with your favorite
characteristics.
To change the settings again, make the changes using the
same procedure. The settings can be changed when the track
is stopped.
7Playing the CD layer of an audio
CD or Super Audio CD
qNoise shaper operation
In this unit, you can select noise shaper on or off for play-
ing tracks.
The noise shaper is turned on and off by pressing the
NOISE SHAPER
button while the track is stopped. When
turned on, the NSHP indicator lights up on the LCD.
* Noise shaping is a type of digital feedback used in the
algorithms for oversampling.This digital feedback enables
improved linearity for low levels (-70 to -90 dB) and bet-
ter noise characteristics in the audible band. However,
this digital feedback is still feedback nonetheless. Gen-
erally, in amplifiers and other equipment, the sound qual-
ity changes based on the amount of feedback. Low feed-
back is said to result in poor audio characteristics but
good sound.
Although no measurement differences are shown in the
SA-11S1, the sound quality is changed. Therefore, make
the setting according to your preferences.
wDC filter operation
The DC filter is turned on and off by pressing the
DC FILTER
button while the track is stopped. When turned
on, the DCF indicator lights up on the LCD.
* The DC filter is effective when the speakers vibrate ab-
normally for discs with recorded audio having extremely
low noise characteristics. (The cutoff frequency is set to
1.7Hz.)
eDigital output off operation
The digital output function is turned on and off by pressing
the
DIGITAL OUT
button while the track is stopped. When
digital output is turned off, the D OFF indicator lights up on
the LCD.
* When digital output is not used, setting to digital output
off enables you to enjoy better sound quality.
Note
* The noise shaper, DC filter, and digital output off have a
memory retention function where the settings remain stored
and unchanged even when the disc is changed or the power
is turned off.
OPERATION
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals

ENGLISH
15
7audio CD, CD layer of Super Audio CD, and high sound quality stereo area
Filter operations
The filter settings can be made while the track is stopped. The filters shown in the table below are available for providing distinctive
filtering according to the operation and Audio CD or Super Audio CD.
Each time the
FILTER
button is pressed, the filter types cycle from FIL1 →FIL2 →FIL3 →FIL1.
The filter setting has a memory retention function so that the setting remains stored and unchanged even when the disc is changed
or the power is turned off.
Filter Selection Table
This is a direct mode that does not perform any
filtering on the DSD data. The original source data
is reproduced without any alteration.
This filter attenuates sections of the DSD data that
exceed 100kHz. In the DAC, operation is also
asymmetric for giving priority to DAC resolution
and raising the multilevel performance to
approximately 40 levels.
This filter attenuates sections of the DSD data that
exceed 100kHz. In the DAC, it provides fully
symmetric operation for 23 levels.
Filter type Audio CD Super Audio CD
FILTER 1
FILTER 2
FILTER 3
This is an original filter using short FIR with
asymmetric preecho and postecho
in the impulse
response.The analog characteristics exhibit slow
roll-off.
This creates a sound venue with richness,
smoothness, and depth consistent with the image
of analog record performances.
This is a filter without preecho or postecho in the
impulse response. It is a special short coefficient
FIR filter
which gives priority to fs (original sample
data).
With analog characteristics, it acts as a slow
roll-off filter to improve sound quality by faithfully
reproducing music signals from deep bass to
midrange.
This is a long coefficient FIR filter with symmetric
preecho and postecho in the impulse response.
With analog
characteristics, it acts as a standard
sharp
roll-off filter. It copies the SAA7220PB
coefficient of 4fs operation that Marantz adopted
in the past with the CD-94, CD-95, CD-95SE and
others as a referential digital filter for audio CD,
but then boosts operation 8-fold.
Note: When playing back the high sound quality stereo area in Super Audio CDs, the analog output level varies slightly in
each filter.
OPERATION
Downloaded from www.Manualslib.com manuals search engine
Downloaded From Disc-Player.com Marantz Manuals